1. LED Leonardo Melo Universidade Federal de Juiz de Fora Electrical Engineering PET Elétrica IEEE UFJF Student Branch

2. Light Emitting Diode A light-emitting diode (LED) is a semiconductor light source. LEDs are used as indicator lamps in many devices, and are increasingly used for lighting. Among other things, they form the numbers on digital clocks, transmit information from remote controls, light up watches and tell you when your appliances are turned on. Basically, LEDs are just tiny light bulbs that fit easily into an electrical circuit. But unlike ordinary incandescent bulbs, they don't have a filament that will burn out, and they don't get especially hot. They are illuminated solely by the movement of electrons in a semiconductor material, and they last just as long as a standard transistor. Electronic Symbol

3. Parts of the LED Electronic symbolElectronic symbol

4. What Is A Diode? The simplest sort of semiconductor device. Broadly speaking, a semiconductor is a material with a varying ability to conduct electrical current. Most semiconductors are made of a poor conductor that has had impurities (atoms of another material) added to it. The process of adding impurities is called doping. In the case of LEDs, the conductor material is typically aluminum-gallium-arsenide (AlGaAs). In pure aluminum-gallium-arsenide, all of the atoms bond perfectly to their neighbors, leaving no free electrons (negatively-charged particles) to conduct electric current. In doped material, additional atoms change the balance, either adding free electrons or creating holes where electrons can go. Either of these additions make the material more conductive. The interaction between electrons and holes in this setup has an interesting side effect -- it generates light! I-V diagram for a diode. An LED will begin to emit light when the on-voltage is exceeded. Typical on voltages are 2–3 volts

5. Lifetime and failure Solid state devices such as LEDs are subject to very limited wear and tear if operated at low currents and at low temperatures. The most common symptom of LED (and diode laser) failure is the gradual lowering of light output and loss of efficiency. Sudden failures, although rare, can occur as well. Like other lighting devices, LED performance is temperature dependent. LED light output actually rises at colder temperatures. Consequently, LED technology may be a good replacement in uses such as supermarket freezer lighting and will last longer than other technologies.

6. Considerations for use Power sources The current/voltage characteristic of an LED is similar to other diodes, in that the current is dependent exponentially on the voltage. This means that a small change in voltage can cause a large change in current. If the maximum voltage rating is exceeded by a small amount, the current rating may be exceeded by a large amount, potentially damaging or destroying the LED. The typical solution is to use constant current power supplies, or driving the LED at a voltage much below the maximum rating. Electrical polarity As with all diodes, current flows easily from p-type to n-type material. However, no current flows and no light is emitted if a small voltage is applied in the reverse direction. If the reverse voltage grows large enough to exceed the breakdown voltage, a large current flows and the LED may be damaged. If the reverse current is sufficiently limited to avoid damage, the reverse-conducting LED is a useful noise diode.

7. Advantages Efficiency: LEDs emit more light per watt than incandescent light bulbs. Color: LEDs can emit light of an intended color without using any color filters as traditional lighting methods need. Size: LEDs can be very small (smaller than 2 mm2) and are easily populated onto printed circuit boards. On/Off time: LEDs light up very quickly. A typical red indicator LED will achieve full brightness in under a microsecond. LEDs used in communications devices can have even faster response times. Cycling: LEDs are ideal for uses subject to frequent on-off cycling, unlike fluorescent lamps that fail faster when cycled often, or HID lamps that require a long time before restarting. Dimming: LEDs can very easily be dimmed either by pulse-width modulation or lowering the forward current. Cool light: In contrast to most light sources, LEDs radiate very little heat in the form of IR that can cause damage to sensitive objects or fabrics. Slow failure: LEDs mostly fail by dimming over time, rather than the abrupt failure of incandescent bulbs. Lifetime: LEDs can have a relatively long useful life. Shock resistance: LEDs, being solid state components, are difficult to damage with external shock, unlike fluorescent and incandescent bulbs which are fragile. Focus: The solid package of the LED can be designed to focus its light. Incandescent and fluorescent sources often require an external reflector to collect light and direct it in a usable manner. Low toxicity: LEDs do not contain mercury, unlike fluorescent lamps.

8. Disadvantages Fluorescent lamps are typically more efficient than LEDs (for lamps with the same CRI). High initial price: LEDs are currently more expensive, price per lumen, on an initial capital cost basis, than most conventional lighting technologies. Temperature dependence: LED performance largely depends on the ambient temperature of the operating environment. Voltage sensitivity: LEDs must be supplied with the voltage above the threshold and a current below the rating. Light quality: The spike at 460 nm and dip at 500 nm can cause the color of objects to be perceived differently under cool-white LED illumination than sunlight or incandescent sources, due to metamerism red surfaces being rendered particularly badly by typical phosphor based cool-white LEDs. Area light source: LEDs cannot provide divergence below a few degrees. In contrast, lasers can emit beams with divergences of 0.2 degrees or less. Electrical Polarity: Unlike incandescent light bulbs, which illuminate regardless of the electrical polarity, LEDs will only light with correct electrical polarity. Droop: The efficiency of LEDs tends to decrease as one increases current

9. Applications LED uses fall into four major categories: Visual signals where light goes more or less directly from the source to the human eye, to convey a message or meaning. Illumination where light is reflected from objects to give visual response of these objects. Measuring and interacting with processes involving no human vision. Narrow band light sensors where LEDs operate in a reverse-bias mode and respond to incident light, instead of emitting light.

10. Thank you for your patience and attention.