1. Equipment Status ARCS equipment status DAQ equipment status
Single module and 4 hybrid
DAQ equipment status
Vienna box, Single rod, Multi-rod
Needed Spares
Mostly power supplies

2. ARCS equipment-modules (UCSB)
UCSB need 1 DEPP and 1 LED board for 3rd module stand
Should ship next week (LED system 2 months away)
UCSB also needs to rotate the 3 ARCS controllers here with 3 with new firmware
Otherwise, false problems found
Bad MUX in fast test
High noise channels in noise
Low injection channels in Pinhole/Cal Injection Test
Should ship next week
DEPP boards all inject noise into system
Sending 3 TOB modules to Aachen for DEPP debug
Need to use Keithley until problem fixed
New order of Keithley needed

3. ARCS equipment-hybrids (UCSB)
UCSB 4 hybrid thermal cycler functional
Critical equipment (spares)
Old ARCS controllers (Correct trigger stuffing)
No old spares, but new ARCS boards maybe stuffed correctly
NIM components
Spares of all modules in-hand
A spare NIM crate would be good
Peltier Power Supply
Need to order spare from CERN Electrics Pool
Peltier element
In hand
Coolie Box
1 spare in US in hand by next week

4. ARCS equipment-modules (FNAL)
All 4 stands fully operational
Use DEPP boards- Do you see same problem?
Which version of firmware in ARCS controllers?
With new firmware delay between clock and ARC ADC clock 2-3 ns
With old firmware delay closer to 7-8 ns
Need to send back all ARCS controllers with old firmware for upgrade
Are DEPP boards injecting noise into system?
Causes higher noise in opens and sensor edges
2 Keithley HV supplies on site sufficient back up

5. ARCS equipment-hybrids (FNAL)
4 hybrid thermal cycler functional
Critical equipment (spares)
Old ARCS controllers (Correct trigger stuffing)
Lenny indicate FNAL has at least one additional old controllers
NIM components
Spares of all modules and crate in-hand
Peltier Power Supply
Need to order spare from CERN Electrics Pool
Peltier element
Did we order this???
Coolie Box
1 spare in US by next week

6. ARCS equipment-hybrids (Mexico)
4 hybrid thermal cycler in assembly
All ARCS equipment in hand next week
Critical equipment (spares)
Old ARCS controllers (Correct trigger stuffing)
No spares on site, will have to be sent by UCSB/FNAL
NIM components
Spares of all modules in-hand
NEED NIM CRATE + SPARE
Peltier Power Supply
Need to order supply + spare from CERN Electrics Pool
Peltier element
Need to order spare

7. Vienna Box (FNAL & UCSB)
Both Vienna Boxes operational
UCSB peltier power supply is having switching problem (see below)
Enough adapter boards in-hand to make second set of cold plates
UCSB needs ~10 TEC adapter boards for cold box
Should be delivered next week
Critical equipment
All spare DAQ equipment in hand except:
No spares for eMUX components
Will order 1 spare set of each component as US spare pool
TPO
Can take from single rod stand if needed (Will need 3 FED per single rod stand w/o TPO)

8. Vienna Box (FNAL & UCSB)
Critical equipment
Peltier power supply
Both sites have had fuse housing melt and UCSB supply is not switching correctly
Ordered spare power supply per site (Delivery in 2 months)
LV Power supply
UCSB had high current Leader power supply overheat, replaced with Agilent PS for single rods
Need to order spare Agilent PS (E3633A) for each site
Should I do this?

9. Rod Test Stands All DAQ equipment in hand except for:
TPO-like object
Both multi-rod stands need this + spares
No idea when this will arrive
Electrometer
No clear if we will ever get this
Should we try to find acceptable multi-channel nano-anameter
Need to run stands to see weak points
Potential problems
DELPHI PS failures
MUX failures
oFED/oFEC failure
Not clear if spares are sufficient (or if we even have all we need) until stands operational