1. Lecture 5 OPTICAL AMPLIFICATIONS BY Halim

2. Why Optical Amplifiers?
Increase transmission distance
by increasing optical power coupled to transmission fiber(power booster)
by compensating optical fiber losses(in-line amplifier, remote pump amplifier)
by improving receiver sensitivity (optical preamplifier)
Function : Amplification of optical signal without conversion to electrical signal
Ingredients : Pump energy, amplification medium
Optical output
Pumping of energy
l l l l l l l l l 1 2 3 4 5 6 7 8 16
...
...
Optical input
amplification
medium
l l l l l l l l l

3. The Need of Optical Amplification
Why? – Extend distance light signal can travel
without regeneration
Erbium-Doped Fiber Amplifiers (EDFAs) – application in long haul. Today’s amplifier of choice.
Erbium-Doped Waveguide Amplifiers (EDWAs) – application in metro and access networks
Raman Amplifiers – application in DWDM
Semiconductor Optical Amplifiers (SOA) – not fiber based type, application in metro and access networks
Standard Fiber
Amplifier
Pump Lasers

4. General Application of Optical Amplification
In-line amplifier
Preamplifier
Power (booster) amplifier
LAN booster amplifier
Amplifier
Standard Fiber
Pump Lasers

5. Amplifier Operation Points10 15 20 25 30 35 40
Booster
amplifier
60 mW
preamplifier
45 mW
in-line
amplifier
30 mW
-10 -5 5 10 15
Output power[dBm]

6. Improvement of System Gain
Booster
amplifier
Preamplifier
In-line
Remote pump
Improvement
in gain(dB)
Key
technology
in length(km)
(APD)
(PIN)
5 - 15
40- 60
High efficiency
Low noise
Supervisory
High pumping
power

7. Nortel OPTERA System
64 wavelengths each carrying 10 Gb/s

8. Applications of Optical Amplifiers
In-Line Amplifier:
Boosts the signal level within a long-distance optical fiber link
Preamplifier:
Boosts the signal to improve the incoming signal-to-noise ratio
Power Amplifier:
Provides “momentum” for transmitted signals at the start of a link
Booster Amplifier:
Compensates for passive coupling and splitting losses in a LAN

9. Optical Amplifiers
Conventional Repeaters in N-WDM systems are very inefficient:
Wavelength de-multiplexing 
O/E conversion  electrical amplification  retiming  pulse shaping  E/O conversion}
wavelength multiplexing
Optical Amplifiers: A single device that amplify multiple format signals that are carried by multiple wavelengths
N -
times

10. Basic Concepts Most optical amplifiers use stimulated emission
An optical amplifier is basically a laser without feedback
Optical gain is realized when the amplifier is pumped optically (or electrically) to achieve population inversion
Gain depends on wavelength, internal light intensity and amplifier medium
Two types: semiconductor optical amplifiers and fiber doped amplifiers

11. Generic optical amplifier
Continuous Wave
(Constant)
Energy is transferred from the pump to signal 2

12. Generic Optical Amplifier
Generic operation of an optical amplifier:
An external source called a pump laser supplies energy
Electrons in an active medium absorb the energy
The energized electrons produce a population inversion at higher levels
Signal photons entering the active medium trigger the electrons to drop to a lower energy level thereby releasing many identical photons
One example of an active medium is an erbium-doped optical fiber

13. Erbium Doped Fiber Amplifiers (EDFA)
Any discussion of lightwave transmission systems must include, at a minimum, a brief description of EDFAs, erbium doped fiber amplifiers. When coupled with DWDM filters, EDFAs are the enabling technology behind the huge growth in lightwave transmission capacity.

14. Basic EDF Amplifier Design
Erbium-doped fiber amplifier (EDFA) most common
Commercially available since the early 1990’s
Works best in the range 1530 to 1565 nm
Gain up to 30 dB
This diagram shows a very basic amplifier that possibly has 5 to 15 dB gain and less than 10 dB noise figure. High performance commercial designs provide output powers from 10 to 23 dBm (10 mW to 200 mW) and noise figures between 3.5 and 5 dB (the physical limit is 3.01 dB).
EDFAs have been deployed in terrestrial and submarine links and now are considered as standard components using a well understood technology.
EDFAs are self-regulating amplifiers. When all metastable electrons are consumed then no further amplification occurs. Therefore a system stabilizes itself because the output power of the amplifier remains more or less constant even if the input power fluctuates significantly.
Input
1480 or 980 nm Pump Laser
Erbium Doped Fiber
Output
Isolator
WDM

15. Doped/Distributed Fiber Amplifiers (EDFA)
The active medium is created by lightly doping silica fiber core by rare earth element Ex: Erbium (Er)
Long fiber length (10-30 m)
Low coupling loss (+)
Transparent to signal format and bit rate
No cross talk
Broad output spectrum (1530 – 1560 nm)
Works only in specific Wavelengths

16. Amplification Process of EDFA3 3
Radiationless
Decay N N
980 nm 2 2
Pump N N 1 1
Optical Pumping to Higher Energy levels
Rapid Relaxation to "metastable" State N 3
~1550 nm N
~1550 nm 2
Signal N 1
Output
Stimulated Emission and Amplification

17. Fig. 11-4: Erbium energy-level diagram

18. EDFA configurations Co-Directional Pumping Counter Directional
Dual Pumping 5

19. Gain versus EDFA length
There is an optimum length that gives the highest gain
Negative gain if too long 6

20. Gain versus pump level Gain decreases at large signal levels
Signal dependant gain
This increases with the pump power

21. Amplified Spontaneous Emission (ASE) Noise7

22. Amplifier Noise
The dominant noise generated in an optical amplifier is called amplified spontaneous emission (ASE) noise.
Results from spontaneous recombination of electrons and holes in the amplifier medium
The recombination occurs over a wide range of electron-hole energy differences
The result is a broad spectral background of noise photons that get amplified as they travel through the EDFA.
Example 1480-nm pump spectrum and a output signal at 1540 nm with the associated ASE noise

23. Optical SNR
In a transmission link with optical amplifiers, the light signal entering the receiver contains ASE noise from the cascade of optical amplifiers.
Need to evaluate the optical signal-to-noise ratio (OSNR).
OSNR is the ratio of the average EDFA optical signal output power Pave to the unpolarized ASE optical noise power PASE:
or, in decibels

24. OSNR versus Q Derived relationship between OSNR and the Q parameter
Solving for OSNR yields

25. EDFA Gain versus Wavelength (From: Ali, Elrefaie, Wagner, Ahmed, J
EDFA Gain versus Wavelength (From: Ali, Elrefaie, Wagner, Ahmed, J. Lightwave Technol., vol. 14, pp, , 1996)
Power gain versus amplifier length
Maximum-gain length is longer for higher wavelengths
For a specific amplifier length the gains vary with λ
This produces a gain skew among different wavelengths
From Ref. 22

26. Gain of Cascaded Amplifiers
EDFA gain is wavelength-dependent in the normal 1530-to-1560-nm EDFA operating window
Gains of 6 wavelengths after a cascade of 27 optical amplifiers
This gain variation must be equalized
Otherwise large SNR differential will appear among the channels after the wavelengths pass through a series of several EDFAs
From Ref. 22

27. Erbium-doped Fibre Amplifier
When you actually look at an EDFA block diagram you see the input on the left the output on the right, photo diodes to measure input and output power levels, pump lasers which are used to excite this piece of erbium doped fiber to a higher energy state, and 1550 light is allowed to pass through.
The isolators are used to keep the 980 and 1480 pump wavelengths contained in the fiber but allow 1550nm light to pass through.

28. Issues of Amplifier Design
Optimization
maximum efficiency
minimum noise figure
maximum gain
maximum gain flatness/gain peak wavelength
Dynamic range, operation wavelength
Gain equalization
Control circuit
Monitoring of amplifier performance

29. Erbium-doped Fibre Amplifier
Gain, G (dB)
10log[(PSignal_Out - Pase) / PSignal_In]
Noise Figure, F = SNRout / SNRin
S-band : nm
C-band : nm
L-band : nm
Spectrum of a typical EDFA

30. Optical Gain (G)
G = S Output / S Input S Output: output signal (without noise from amplifier) S Input : input signal
Input signal dependent
Operating point (saturation) of EDFA strongly depends on power and wavelength of incoming signal
Gain (dB)
1540
1560
1580 10
1520 20 40 30
-5 dBm
-20 dBm
-10 dBm
P Input: -30 dBm
The gain versus wavelength curve of the EDFA (as well as the ASE versus wavelength plot) can vary with input signal wavelength and power.
Carefully watch how the gain decreases with increasing input power. If the input is -20 dBm then the gain is about 30 dB at 1550 nm, resulting in +10 dBm output. If the input is -10 dBm then the gain is about 25 dB and the output about +15 dBm. In other words, when the input changes by a factor of ten then the output changes only by a factor of three in this power range.
Above -10 dBm input the amplifier is in full compression: -5 dBm input power has 20 dB gain, therefore the 5 dB increase in input power has no effect on the output power (but it may have improved the noise figure).
You can also recognize the saturation by the fact that the traces become more flat when the input power increases. Saturation is a preferred point of operation because it stabilizes the system and reduces noise without causing nonlinear effects (like clipping) inside the amplifier for high speed modulation.
Wavelength (nm)

31. Noise Figure
Noise figure describes how close an amplifier comes to an ideal amplifier that amplifies the input spectrum including noise but does not add any noise. According to quantum physics, it is impossible to build an optical amplifier with better than 3.0 dB noise figure.
The noise figure formula compares noise density (PASE / BOSA) measured at the output but normalized to the input (1/G term) with the “quantum noise” of the incoming photons (h*). Note that this formula is based on some assumptions usually present in fiberoptic communication systems (for a detailed discussion, see “Fiber Optic Test And Measurement” by Dennis Derickson, ISBN ).
As we can see from the measurements shown here(next slide), the noise figure becomes better with increasing wavelength. The traces overlap significantly because even at -30 dBm input power the amplifier is already saturated sufficiently. You have to drop input power considerably before the noise figure becomes noticeably worse.

32. Noise Figure (NF)
NF = P ASE / (h• • G • B OSA) P ASE: Amplified Spontaneous Emission (ASE) power measured by OSA h: Plank’s constant : Optical frequency G: Gain of EDFA B OSA: Optical bandwidth [Hz] of OSA
Input signal dependent
In a saturated EDFA, the NF depends mostly on the wavelength of the signal
Physical limit: 3.0 dB
Noise Figure (dB) 10
7.5
Noise figure describes how close an amplifier comes to an ideal amplifier that amplifies the input spectrum including noise but does not add any noise. According to quantum physics, it is impossible to build an optical amplifier with better than 3.0 dB noise figure.
The noise figure formula compares noise density (PASE / BOSA) measured at the output but normalized to the input (1/G term) with the “quantum noise” of the incoming photons (h*). Note that this formula is based on some assumptions usually present in fiberoptic communication systems (for a detailed discussion, see “Fiber Optic Test And Measurement” by Dennis Derickson, ISBN ).
As we can see from the measurements shown here, the noise figure becomes better with increasing wavelength. The traces overlap significantly because even at -30 dBm input power the amplifier is already saturated sufficiently. You have to drop input power considerably before the noise figure becomes noticeably worse.
5.0
1520
1540
1560
1580
Wavelength (nm)

33. EDFA Categories In-line amplifiers
Installed every 30 to 70 km along a link
Good noise figure, medium output power
Power boosters
Up to +17 dBm power, amplifies transmitter output
Also used in cable TV systems before a star coupler
Pre-amplifiers
Low noise amplifier in front of receiver
Bi-directional amplifiers
An amplifier which work in both ways
The output gain, output power and noise figure of EDFAs can be tweaked by various design modifications.
Using 980 nm pumps usually produce EDFAs with lower noise figures. EDFAs of this type make better preamps. It is thought that the reason for this NF improvement is that the pump wavelength is farther out of the emission band and, for this reason, reduces ASE.
Remotely pumped EDFAs allow system designers to extend medium range submarine links, such as those between islands. Their main advantage is that there are no electronics and therefore no power needs along the link, a fact that improves reliability and reduces cost.

34. EDFA Categories

35. Typical Design
Figure in the slide shows an EDFA with all the options design
Coupler #1 is for monitoring input light
Coupler #2 is optional and is used for monitoring backreflections. The microcontroller can be set to disable the pump lasers in case the connector on the output has been disconnected. This provides a measure of safety for technicians working with EDFA’s.

36. Typical Design

37. Erbium-Doped Fiber Amplifiers
Figure in the next slide shows two single-stage EDFA’s packaged together
Mid stage access is important for high performance fiber optic systems requiring a section of dispersion-compensating fiber (DCF)
The high loss of DCF (10dB+) is compensated by the EDFA\
The main advantage of SOA’s and EDFA’s is that amplification is done with photons, as opposed to electronic amplification (requires O/E and E/O conversion)

38. Erbium-Doped Fiber Amplifiers

39. Typical Packaged EDFA

40. EDFAs In DWDM Systems Gain flatness requirements Gain competition
Optical amplifiers in DWDM systems require special considerations because of:
Gain flatness requirements
Gain competition
Nonlinear effects in fibers
DWDM systems can cause additional complications for designers. Let us look at the key issues one at a time.
Note that most of these aspects become irrelevant on DWDM systems over short distances. For example, many municipal links do not need any amplifier at all (the average cable length between network terminals in big cities can be as short as seven miles).

41. Gain Flatness Gain versus wavelength Compensation techniques
The gain of optical amplifiers depends on wavelength
Signal-to-noise ratios can degrade below acceptable levels (long links with cascaded amplifiers)
Compensation techniques
Signal pre-emphasis
Gain flattening filters
Additional doping of amplifier with Fluorides G 
The gain and noise figure of the first generations of erbium-doped fiber amplifiers (EDFAs) were not flat over wavelength. The amplitude or signal-to- noise ratio (SNR) can degrade quicker than desired if amplifiers are cascaded. Therefore they may not be well suited for DWDM applications.
More recent designs compensate this effect with different fiber doping, compensation filters or simply by pre-emphasizing the channels at the transmitter side in order to achieve a good signal-to-noise ratio for all channels.

42. Gain Competition
Total output power of a standard EDFA remains almost constant even if input power fluctuates significantly
If one channel fails (or is added) then the remaining ones increase (or decrease) their output power
Output power after channel one failed
In a simple model, an amplifier has a pool of optical energy available for amplification. If a channel drops in a DWDM system (or is added) then fewer (more) signals compete for this energy. As a result, the output power for the other channels increases (decreases) accordingly. These unwanted fluctuations must be compensated by either a high tolerance of the receiver for power fluctuations or by adjusting the power of the pump lasers inside the amplifier.
Equal power of all four channels

43. Output Power Limitations
High power densities in SM fiber can cause
Stimulated Brillouin scattering (SBS)
Stimulated Raman scattering (SRS)
Four wave mixing (FWM)
Self-phase and cross-phase modulation (SPM, CPM)
Most designs limit total output power to +17 dBm
Available channel power: 50/N mW (N = number of channels)
The total power (sum of all channels) coming out of an amplifier can cause nonlinear effects in the fiber behind the amplifier. Because the effects can cause significant distortions, system designers must carefully balance EDFA power levels, amplifier spacing and signal-to-noise requirements.
Standards for long haul systems typically propose up to eight channels at 100 or 200 GHz spacing with up to twelve EDFAs to cover a span up to 600 km. Companies offering systems with more channels often target them for regional links with less or no amplifiers.

44. Erbium Doped Waveguide Amplifier (EDWA)
An erbium-doped waveguide amplifier (EDWA) consists of waveguides embedded in an amorphous erbium-doped glass substrate.
The erbium atoms provide the glass with gain in the 1,550-nm fibre-optic window.
The waveguide itself is a localised increase in the glass refractive index.
Today's manufacturers have several methods available to produce erbium-doped glass waveguides: PECVD and flame hydrolysis deposition, sputtering, ion-exchange, or ion implantation.
For the manufacture of waveguide amplifiers, the two most advanced methods are ion-exchange and sputtering.

45. Erbium Doped Waveguide Amplifier (EDWA)
EDWA advantages
EDWAs are inherently compact.
One of the smallest gain block amplifiers to date, featuring 15-dB gain at 1,535 nm, fits in a 130x11x6-mm package.
EDWAs also offer a better price/performance ratio than comparable EDFAs for access and metro network applications.

46. Raman Amplifier Raman Amplifier was demonstrated in the 1980s
Unavailability of high-power diode laser pump source
Why do you need it :
amplify signals from 1270 to 1670 nm
any optical fiber can serve as the amplifying medium
Raman process itself provides high-power laser
Disadvantage: Cross-talk

47. Raman Amplifiers
A Raman optical amplifier is based on the nonlinear effect stimulated Raman scattering (SRS), which occurs in fibers at high optical powers
An interaction between an optical energy field and the vibrational modes of the material lattice structure transfers power to higher wavelengths over a broad spectral range of 80 to 100 nm
The shift to a particular longer wavelength is called the Stokes shift

48. Distributed Raman Amplifier Application
A Raman amplifier makes use of the standard transmission fiber itself as the amplification medium.
For the distributed Raman amplifier, optical power from one or more Raman pump lasers is inserted into the far end of the transmission fiber toward the transmitting end.
Thereby the final 20 to 40 km of the transmission fiber is converted into a preamplifier.

49. Raman Amplifier Setup
Pump lasers with high output powers in the 1400-to-1500-nm region are required for Raman amplification of C- and L-band signals.
A pump-power combiner multiplexes the outputs from pump lasers operating at different wavelengths onto a single fiber.
Examples might be 1425, 1445, 1465, and 1485 nm.
The gain flattening filter (GFF) equalizes the gains at different λs.

50. Raman Amplifier Components
Pump lasers that provide fiber-launch powers of up to 500 mW are available in standard 14-pin butterfly packages.
Pump-power couplers are called 14XX-nm pump-pump combiners.

51. Raman Amplifier
Amplifier Gain

52. Raman Amplifier
Wide bandwidth Raman amplifier can be realized using multiple pumps

53. EDFA+Raman
Combined Raman and EDFA transmission Experiment: DWDM (Lucent)

54. Raman Amplifier Advantages Disadvantages
Variable wavelength amplification possible
Compatible with installed SM fibre
Can be used to "extend" EDFAs
Can result in a lower average power over a span, good for lower crosstalk
Very broadband operation may be possible
Disadvantages
High pump power requirements, high pump power lasers have only recently arrived
Sophisticated gain control needed
Noise is also an issue

55. Semiconductor Optical Amplifiers
The SOA construction is similar to a resonator cavity of a laser diode.
The SOA has an active region of length L, width w, and height d.
The end facets have very low reflectivities in order for the optical signal to pass through the amplification cavity only once.
External current injection is the pumping method used to create the population inversion needed for having a gain mechanism in SOAs.
If the single-pass gain in the absence of light is G0 and the amplifier saturation power Pamp,sat is the internal power level at which the gain per unit length has been halved, then

56. Semiconductor Optical Amplifier (SOA)
Basically a laser chip without any mirrors
Metastable state has nanoseconds lifetime (-> nonlinearity and crosstalk problems)
Potential for switches and wavelength converters
Research labs around the world have been working on other optical amplifier designs but very few of them have been deployed (besides field trials).
SOAs possibly will be used to compensate losses in integrated optics or for special switch applications. PDFAs are very difficult to manufacture and yet have not been very cost effective for large-scale use in networks.

57. Semiconductor optical amplifiers, like their semiconductor-laser, consist of gain and passive regions. Layers of antireflective coatings prevent light from reflecting back into the circuit while the incoming signal stimulates electrons in the gain region

58. Semiconductor Optical Amplifier (SOA)
Semiconductor optical amplifiers are similar in construction to semiconductor lasers. They consist of a gain (active) section and a passive section constructed of a semiconductor material such as indium phosphide. The main difference is that SOAs are made with layers of antireflection coatings to prevent light from reflecting back into the circuit. Optical gain occurs as excited electrons in the semiconductor material are stimulated by incoming light signals; when current is applied across the p-n junction the process causes the photons to replicate, producing signal gain. The gain medium can be either a bulk or a multiple-quantum-well active layer.

59. Semiconductor Optical Amplifiers
Semiconductor Optical Amplifiers (SOA’s)
Laser diodes without end mirrors
Fiber attached to both ends
Amplified version of the optical signal is produced
Advantage: bidirectional
Drawbacks
High-coupling losses
High noise figure

60. Semiconductor
By adjusting the chemical composition of III-V semiconductors (typically GaInAsP) the band gap can be adjusted to give optical gain in the telecommunications windows of interest. The devices are typically 250mm long although devices of up to 1mm have been made. In general the longer devices can achieve higher gain and wider bandwidths.
The optical bandwidth of a semiconductor optical amplifier (SOA) can be as large as 100 nm and the fact that the energy source is a DC electrical current makes these devices look promising as optical amplifiers.

61. Limitations/Advantages/Applications
SOAs have severe limitations:
Insufficient power (only a few mW). This is usually sufficient for single channel operation but in a WDM system you usually want up to a few mW per channel.
Coupling the input fibre into the chip tends to be very lossy. The amplifier must have additional gain to overcome the loss on the input facet.
SOAs tend to be noisy.
They are highly polarisation sensitive.
They can produce severe crosstalk when multiple optical channels are amplified.
This latter characteristic makes them unusable as amplifiers in WDM systems but gives them the ability to act as wavelength changers and as simple logic gates in optical network systems.
A major advantage of SOAs is that they can be integrated with other components on a single planar substrate. For example, a WDM transmitter device may be constructed including perhaps 10 lasers and a coupler all on the same substrate. In this case an SOA could be integrated into the output to overcome some of the coupling losses.

62. SOA operation E
Conduction band
Optical transition k
Valence band

63. SOA operation
The DC current applied to the device results in electrons being pumped into the (normally empty) conduction band and removed from the (normally full) valence band. This creates the population inversion which is a pre-cursor to optical gain. When signal photons travel through the device they cause stimulated emission to occur when an electron and hole recombine.
The phase effects in these devices can be quite strong with a gain change of 3dB corresponding to roughly a phase change of p.

64. Wideband Optical Amplifiers
A combination of two amplifier types can provide amplification in both the C- and L-bands or in the S- and C-bands. Three amplifier types can provide signal gains in the S-, C-, and L-bands or other combinations.
The amplifiers could be based on thulium-doped silica fibers for the S-band, standard EDFAs for the C-band, gain-shifted EDFAs for the L-band
Different versions of Raman amplifiers also can be used
The amplifier combinations can be in parallel or in series.

65. Optical Fiber Laser
Optical fibers doped with rare-earth elements also can be used to create an optical fiber laser.