1. doc.: IEEE /XXXr0
Sep 19, 2007
Project: IEEE P Working Group for Wireless Personal Area Networks (WPANs)‏
Submission Title: [Resolutions to comments CID 1, 2, 102, 118, 134, 138, 142 and 188]
Date Submitted: [12 Nov 2008]
Source: [C.S Sum, T. Baykas, R. Funada, M.A .Rahman, C.W Pyo, F. Kojima, H. Harada, S. Kato, M. Umehira, H. Nakase, A. Bourdoux1, A. Valdes-Garcia2, Y. Katayama2,, J. Oh3, S.K Yong3, C.S Choi4, M. Noda5, I. Lakkis6]
Company [NICT, IMEC1, IBM2, Samsung3, IHP4, Sony5, Tensorcom6]
Address [3-4, Hikarino-oka, Yokosuka, , Japan]
Voice: [ ], FAX: [ ],
Re: []
Abstract: []
Purpose: [This document provides a list of the editing staff that will be working on c.]
Notice: This document has been prepared to assist the IEEE P It is offered as a basis for discussion and is not binding on the contributing individual(s) or organization(s). The material in this document is subject to change in form and content after further study. The contributor(s) reserve(s) the right to add, amend or withdraw material contained herein.
Release: The contributor acknowledges and accepts that this contribution becomes the property of IEEE and may be made publicly available by P
Name - WirelessHD

2. Summary 1
This document responds to the comments on SC class 3 related comments: CID 1, 2, 102, 118, 134, 138, 142 and 188.
2 MCSs are added into class 3 for SC PHY to support specific high data rate applications such as HDMI.
Resolution: Include the following MCS as SC class 3 into D02.
HR1: p/2-8PSK with LDPC(672,504) – 3.8Gbps (PW=0), 3.4Gbps (PW=64)
HR2: p/2-16 QAM with LDPC(672,504) – 5.1Gbps (PW=0), 4.5Gbps (PW=64)

3. Summary 2
Corresponding changes on other parts of D02 due to the MCS addition are also presented.
Introduction for SC PHY
SC PHY MCS class categorization table
MCS table
Text on modulation and constellation diagram
Supported data rates field
MCS identifier in PHY header
Others if applicable

4. MCS Categorization of the SC PHY
Add the following into Table 101.
The description of Class 3 MCS will be added into the general introduction in 12.2.
Class
Categorization
Class 3
Data Rates at PHY-SAP > 3Gb/s

5. MCS Table Add the following into Table 102. MCS class MCS identifier
Data rate (Mbps) PW=0
Data rate (Mbps) PW=64
Modulation scheme
Spreading factor
FEC type
FEC rate
Class 3
HR1
3888
3402
p/2-8PSK 1
LDPC(672,504)
0.75
HR2
5184
4536
p/2-16 QAM

6. Text on MCS modulation and constellation diagram
The explanation for class 3 modulation will be copied from previous versions of draft: 8PSK (before DF0) and 16QAM (D01).
The following subclauses will be added:
p/2 8PSK
p/2 16-QAM
The constellation diagrams will be copied from similar sources.
Constellation diagrams for p/2 8PSK and p/2 16- QAM will be added into Figure 130 in D02.

7. Supported Data Rates Field
Add the following bits (in red) in Figure 126.
Add the descriptions of the bits into
The SC 8PSK field shall be set to one if the p/2 8PSK is supported by the SC PHY DEV and shall be set to zero is otherwise.
The SC 16-QAM field shall be set to one if the p/2 16- QAM is supported by the SC PHY DEV and shall be set to zero is otherwise.
bits: 1 1
SC spreading
SC QPSK
SC 8PSK
SC 16QAM
SC LDPC 1
SC LDPC 2
AV 16- QAM
HSI 16- QAM

8. MCS identifier in PHY header
Add the following into Table 115.
MCS
MCS identifier
0b01100
HR1
0b01101
HR2
0b b11111
Reserved

9. EVM
Add the following into Table 121.
MCS class
EVM (dB)
Class 3
-21