1. Horticulture Science Lesson 55 Caring for Fresh Cut Flowers and Foliage

2. Terms acidic alkaline bent necks conditioning ethylene inhibitors
floral preservatives
graded
hard water

3. Terms hardened precooled respiration salinity senescence soft water
transpiration
turgid

4. When a flower is cut, what are its needs?
Even after fresh flowers have been removed from plants, they continue to photosynthesize, that is, they produce food from sunlight.
Two needs for maintaining the health of cut flowers are water and sugar.

5. When a flower is cut, what are its needs?
1. A flower is 90 percent water.
Plant cells that are filled with water are called turgid.
A water analysis can be conducted to determine quality.

6. When a flower is cut, what are its needs?
2. A pH test of the water will determine whether water is acidic or alkaline.
An acidic pH has a reading below 7, and pH readings above 7 indicate an alkaline solution.
If a floral preservative is added to water, it will increase the acidic level, thereby increasing water uptake in plants.

7. When a flower is cut, what are its needs?

8. When a flower is cut, what are its needs?
3. Water is classified as either hard water, that which contains a high level of minerals, or soft water, which has been treated to lower the mineral level.

9. When a flower is cut, what are its needs?
4. Salinity is the measurement of the total dissolved salts in water.

10. When a flower is cut, what are its needs?
Sugars are the food source for cut flowers.
The two most common sugars are sucrose and dextrose.

11. When a flower is cut, what are its needs?
Fresh cut flowers require a healthy environment.
1. Fresh cut flowers should be placed in an environment free from ethylene gases, which cause deterioration in the flowers.

12. When a flower is cut, what are its needs?
2. Conditioning is the preparation of cut flowers and greens when they arrive at the design site.
a. Flower stems should be re-cut and defoliated to a point that no leaves will be in the water solution.

13. When a flower is cut, what are its needs?
b. Flowers are placed in water that is approximately 100 to 110°F or about the temperature of a warm bath.
c. Once the flowers are full of water, they can be placed in a cooler that is 34 to 38°F.

14. When a flower is cut, what are its needs?
Another important factor in the handling of cut flowers and greens is sanitation.
Sanitation or cleanliness improves the vase life of flowers.
Hands, tools, knives, shears, containers and work areas need to be kept sanitary.
Introduction of bacteria and organisms can be avoided by cleaning work areas, coolers and containers on a regular basis.

15. What causes a flower to deteriorate and die?
As soon as a flower is cut from the mother plant, it begins to deteriorate because the flower no longer has a water or food source.
The flower will eventually die, which is referred to as senescence.
Major causes of flower deterioration and death are determined by genetics, lack of water, time of harvest, ethylene, and disease or damage.

16. What causes a flower to deteriorate and die?
The life of each flower is based on its genetics.
The natural lives of flowers differ between species.
The flowers of the daylily live just one day.
Dutch irises live 3–5 days.
Roses have a life of 5–7 days.
Carnations last 10–14 days
Chrysanthemums live 14–21 days.
The goal is to obtain the maximum life of each flower as allowed by nature.

17. What causes a flower to deteriorate and die?
Wilting is caused by the inability of plant tissues to absorb enough water to replace water lost by transpiration.
Transpiration is the loss of water from plant tissues.
The rate of transpiration increases in warm environments with low humidity.
Transpiration can be reduced by avoiding drafts and over-handling flowers.

18. What causes a flower to deteriorate and die?
1. Blocked vascular tissue can restrict the movement of water within a plant and cause wilting.
Stem blockage is the most common cause of poor absorption.
The xylem becomes clogged and no water movement can occur in the stem.
2. Flowers and foliage that are fully hydrated are said to be turgid.

19. What causes a flower to deteriorate and die?
The timing of flower harvest influences flower life.
1. The time of day when flowers are cut is important.
Flowers should never be cut when they are wilted.
Avoid cutting in the heat of the day.
Evening is the best time because plants have been making sugars throughout the day.
Morning is the second best time to cut because plants are full of water.

20. What causes a flower to deteriorate and die?
2. The stage of flowering should be considered.
The best time to harvest is just before a flower is fully open.
Exceptions to the rule include the daisy and flowering bulb crops, which are harvested in bud stage, and the calla lily, which will not develop further once it is cut.

21. What causes a flower to deteriorate and die?
Ethylene gas promotes senescence.
Ethylene gas is a natural plant hormone produced by aging flowers, foliage, fruits, and vegetables.
Common signs of ethylene exposure include large amounts of fallen petals, dropped florets, and yellowing leaves.
Growers and wholesalers prevent this damage by using ethylene inhibitors, which are products that block or tie up the gas.
They also strive to keep storage areas free of aging, decaying plant materials.

22. What causes a flower to deteriorate and die?
Disease or damage shortens the life of floral materials.

23. How are cut flowers and foliage conditioned to maximize vase life?
Conditioning plant materials includes a number of steps.
1. Flowers should be unpacked and inspected upon receipt.
2. Prioritize the order of processing.
3. Remove sleeves, ties, and any foliage that might contact water in a container.

24. How are cut flowers and foliage conditioned to maximize vase life?
4. Under warm water, re-cut all stems, removing ½ inch to 1 inch.
5. Use specific treatment solutions as needed.

25. How are cut flowers and foliage conditioned to maximize vase life?
6. Place in a floral preservative solution mixed at the proper concentration.
7. Let the flowers remain at room temperature for two to three hours to increase water uptake.
8. Place the flowers in a cooler set at 34 to 38°F with a high humidity level and constant light.

26. How are cut flowers and foliage conditioned to maximize vase life?
Flowers with milky stems, such as poinsettias and poppies, should be treated by quickly dipping them in boiling water for five seconds and then placing them in a floral preservative solution.

27. How are cut flowers and foliage conditioned to maximize vase life?
They can be revived by re-cutting the stems under water and placing the entire stems in a warm preservative solution.

28. How does a floral preservative extend the life of cut flowers?
Floral preservatives will extend the life of cut flowers.
A preservative contains a sugar as a supplemental food source, an acidifier to decrease the chance of stem clogging, and a bactericide to kill bacteria in a vase or stem.

29. How are flowers sent from the field to the florist?
The majority of cut flowers sold in the United States are produced in foreign countries.
The commercial packing and shipping process affects the life span of cut flowers in the floral market.

30. How are flowers sent from the field to the florist?
They are also graded by stem quality, length, and strength.
The flowers are then placed in bundles and sleeved for shipping.
Delicate flowers such as Fuji mums and Gerbera are individually sleeved.

31. How are flowers sent from the field to the florist?
After bundling, the flowers are boxed for shipment and precooled, a method of quickly replacing the warm air with cool air inside the box; this is also called being dry packed.