1. Full-arch LUMINEERS Placement Technology
LUMITray Technology
Full-arch LUMINEERS Placement Technology

2. Process Overview 1st visit scan 3D design produce DESIGN & PRODUCTION
IMPRESSIONS
PHOTOGRAPHS
DESIGN & PRODUCTION
scan
3D design
produce 2

3. Digital CAD/CAP Software
LUMITray uses state-of-the-art technology that facilitates digital design and fabrication for beautifully precise veneers.
With this technology, technicians build the veneers – to micron accurate specifications – directly on a digital 3-D model.
This process creates a superior fit at the gingival margin, which means less finishing.

4. Digital Preview
Because the system is digital, you can preview, change and accept the restoration from your dental office before it’s fabricated, ensuring that final restorations are to exact specifications. 4

5. Digital Preview

6. Without Reshaping Before Impression
With Reshaping Before
Impression

7. LUMIKey Reshaping Guides
If reshaping is requested, you will receive a LUMIKey reshaping guide, which is created using the same digital specifications of the restoration.
The LUMIKey simplifies the placement process and produces accurate results.

8. LUMIGuard Is your LUMITray patient a bruxer? LUMIGuard is the answer.
LUMIGuard is an occlusal protection plate that can be worn during the day or night.
The custom fit and minimalistic design of LUMIGuard means you can provide comfortable protection for your patients’ perfect new smiles.
Available at the time of placement of the LUMINEERS with LUMITray.

9. LUMITray: Step-by-Step
Placement Procedure
LUMITray: Step-by-Step

10. Step 1
Step 1: Reshaping Trays

11. Step 2 Break the glaze of the enamel
Take medium coarse or fine diamond and roughen the outer surface of the enamel
Draw the diamond across the incisal edge at a 45-degree angle (This allows for a more full seating of the LUMINEERS and increases mechanical retention)

12. Step 2 Lightly roughen the facials of all teeth to receive Lumineers
Be thorough and methodical

13. Step 3 Etching Etch the teeth with Etch ‘N’ Seal for 20 seconds
Rinse thoroughly with water 13

14. Step 5 Bonding Add 5 coats of Tenure A + B Add 1 coat of Tenure S
Tooth surfaces must be shiny 14

15. Step 6 Prime-Bonding on LUMINEERS
These come pre-etched, pre- hydrolyzed and pre-silanated
Add 1 coat of Tenure A + B on the inner side of the LUMINEERS
Add 1 coat of Tenure S on the inner side of the LUMINEERS 15

16. Ultra-Bond Plus on LUMINEERS
Step 7
Ultra-Bond Plus on LUMINEERS
Add a layer of Ultra-Bond Plus resin cement to the inner side of the LUMINEERS. Work upwards from incisal edge of the LUMINEERS to gingival edge and keep contact with the LUMINEERS (see diagram) 16

17. Step 8 Insert the LUMITray
Remove the Paint-On Dental Dam or interdental strips!
Center the LUMITray (midline)
Insert the tray in one smooth movement. Apply a light, continuous, buccal pressure. Take your time for the placement.
Remove excess Ultra-Bond cement at the gingiva with microbrush 17

18. Step 9 Set the Sapphire Plus Light for 3 seconds
Tack-cure with a sweeping movement of the 9mm tip
With a probe remove more excess cement
Light-cure each tooth 3 seconds through tray with Sapphire Plus 18

19. Step 10 Remove LUMITray Remove the LUMITray (don’t twist)
Remove the retentions with Schure 349
Remove any excess on the lingual side of the teeth with Schure 349 19

20. Open Interdental Spaces
Step 11
Open Interdental Spaces
Remove Ultra-Bond Plus cement from interproximal spaces with a CeriSaw
Maintain complete control over the instrument. If difficult, postpone to follow-up visit.
Advise you leave the contacts alone for two days. 20

21. Light-Cure the LUMINEERS
Step 12
Light-Cure the LUMINEERS
Cure each LUMINEERS individually for a second time on both the lingual and buccal sides for 5 seconds with the Sapphire Plus Light 21

22. Check Occlusion and Polish
Step 13
Check Occlusion and Polish
Check and finish the occlusion
Polish the LUMINEERS with Porcelain Polishing Paste 22

23. Thick Blue Paper Makes Contact Areas Obvious
Note: cuspal inclines; adjust areas inside circles
Note: vertical stops, cusp tips and fossa

24. Step 14 Final Check Take after photos Give the patient their LUMIGuard24

25. Before and After