1. Cooling System

2. Combustion of the air-fuel mixture in the cylinders generates heat which produces high pressure, to force the piston down in the power stroke.
Not all of this heat can be converted into useful work on the piston, and it must be removed to prevent seizure of moving parts. This is the role of the cooling system. Most engines are liquid-cooled.

3. A liquid-cooled system uses coolant - a fluid that contains special chemicals mixed with water. Coolant flows through passages in the engine, and through a radiator.

4. Water Jacket: The water passages in the cylinder block and cylinder head form the engine waterjacket.

5. In the cylinder block, the water jacket completely surrounds all cylinders along their full length.
Within the jacket, narrow passages are provided between the cylinders for coolant circulation around them.

6. In addition, water passages are provided around the valve seats and other hot parts of the cylinder head, the water jacket covers the combustion chambers at the top of the cylinders and contains passages around the valve seats when the valves are located in the head.

8. Water Pump: A water pump is used to circulate water throughout the engine block, cooling and heater systems. The water pump is usually driven by the engine via serpentine belt in most cases.

10. A water pump is comprised of a main housing body, flange, main shaft, bearings, impeller, seals and a gasket to seal in against the block. When engine RPM increase so does the water pump flow rate. A water pump will typical last between 60,000 and 100,000 miles.

12. Thermostat: The thermostat in your vehicle is what regulates how fast the engine warms up and at what operating temperature it will run.

13. The pellet-type thermostat that is used in modern pressurized cooling systems incorporates the piston and spring principle.
The thermostat consists of a valve that is operated by a piston or a steel pin that fits into a small case, containing a copper impregnated wax pellet.

14. A spring holds the piston and valve in a normally closed position.
When the thermostat is heated, the pellet expands and pushes the valve open. As the pellet and thermostat cools, spring tension overcomes pellet expansion and the valve closes.

16. Warming the engine up is very important due to the different expansion rates of all the internal parts (aluminum, steel, cast iron and rubber seals).
If an engine is running too cold, the tolerances within are not correct and damage may ensue.

17. Today’s vehicles are designed to run anywhere between degrees Fahrenheit, it is the thermostats job to regulate the fluid flow through the radiator to keep the temperature at a predetermined level.
Most fuel injected vehicles use a 195-degree thermostat, so by 200 degrees it is fully open and letting the fluid flow through the radiator and back to the engine.

18. Most engines have a small coolant bypass passage that permits some coolant to circulate within the cylinder block and head when the engine is cold and the thermostat is closed.
This provides equal warming of the cylinders and prevents hot spots.
When the engine warms up, the bypass must close or become restricted. Otherwise, the coolant would continue to circulate within the engine and too little would return to the radiator for cooling.

19. The radiator accepts hot coolant from the engine, and lowers its temperature. Air flowing around, and through the radiator takes heat from the coolant. The lower-temperature coolant is returned to the engine through a pump.

20. The radiator is basically a finned box mounted at the front of the vehicle that the coolant is forced through so that air may pass across it and cool the anti-freeze-coolant. They are covered in fins that act as heat syncs to help dissipate the heat.
The fins of the radiator effectively increase the surface area of the radiator which allows a greater amount of heat exchange.

22. The radiator has 2 tanks and a core.
The materials used in the radiator must be good heat conductors like brass or copper. Brass and copper are often used for tanks, combined with a copper core.
Modern vehicles often use plastic tanks combined with an aluminium core. This saves weight but still provides good heat transfer.

23. The core consists of a number of tubes that carry coolant between the 2 tanks. The tubes can be in a vertical downflow pattern, or a horizontal crossflow pattern.

26. In the core, small, thin, cooling fins are in contact with the tubes
In the core, small, thin, cooling fins are in contact with the tubes. The shape of the fins increases the surface area exposed to the air.
Where coolant touches tube walls, and where the tubes touch the fins, heat is removed from the coolant by conduction, then by radiation and convection at the surface of the fins. Air rushing by carries the heat away.
Liquid emerges cooler at the bottom of the radiator. It travels through the lower radiator hose to the water pump inlet, then through the engine again.

27. Air cooling is common on smaller internal combustion engines
Air cooling is common on smaller internal combustion engines. Some engines use cooling fins. Their design makes the exposed surface area as large as possible, which allows more heat energy to radiate away, and be carried off in convection currents in the air.

28. Some engines also use a fan to direct air over the fins.

29. Cooling Fans:
In a vehicle moving at high speed, airflow through the radiator cools the coolant, but at low speed or when the engine is idling, extra airflow comes from a fan.

30. Fans can be driven in different ways
Fans can be driven in different ways. More and more modern vehicles now use an electric fan. Air-conditioned cars often have extra fans.
Electric fans can be behind the radiator, in front, or both. This arrangement would be difficult with a belt-driven fan.
Some fans can be driven from the crankshaft.
When an engine is mounted longitudinally, its fan is usually mounted on the water pump shaft. The drive belt then turns the water pump and fan.

33. Fan blades can be rigid or flexible
Fan blades can be rigid or flexible. Rigid blades tend to be noisy and use more energy. This noise can be reduced by using irregular spacing of the fan blades.

34. Some vehicles use a shroud to direct all of the air that the fan moves, through the radiator core.
At high speeds, plenty of air is already flowing through the radiator.
If the fan is always working at full speed, it’s a waste of energy. And since the engine drives the fan, it’s a waste of fuel too.
What’s needed is some way to control the fan. A heat-sensitive switch in contact with the coolant can work like a thermostat, and turn the fan on and off according to coolant temperature.

35. Another way to alter the speed of the fan is with a viscous hub
Another way to alter the speed of the fan is with a viscous hub. This type of fan slips when it is cold, but as the engine heats up, it grips more and more.

36. Radiator pressure cap:
If a coolant boils, it can be as serious for an engine as having it freeze.
Boiling coolant in the waterjacket becomes a vapor. No liquid is left in contact with the cylinder walls or head. Heat transfer by conduction stops. Heat builds up, and that can cause serious damage.

38. One way to prevent this is with a radiator-pressure cap that uses pressure to change the temperature at which water boils.
As coolant temperature rises, the coolant expands and pressure in the radiator rises, and that lifts the boiling point of the water.

39. Engine temperature keeps rising, and the coolant expands further
Engine temperature keeps rising, and the coolant expands further. Pressure builds against a spring-loaded valve in the radiator cap until at a preset pressure, the valve opens.
In a recovery system, the hot coolant flows out into an overflow container.

40. As the engine cools, coolant contracts and pressure in the radiator drops. Atmospheric pressure in the overflow container then opens a second valve, a vacuum vent valve, and overflow coolant flows back into the radiator.
This system stops low pressure developing in the radiator, and that stops atmospheric pressure collapsing the radiator hoses.

41. Recovery system:

42. Coolant:
In the beginning, water was used for cooling systems, as it is the most efficient fluid to absorb and dissipate heat.
The disadvantage of using water is that it freezes, boils, and will cause rust.

43. Then water was mixed with ethylene glycol, which worked as an anti-freezing agent, it also increased the boiling point of the mixture dramatically.
Ethylene glycol can be heated up to 250°F before becoming ineffective.
The cooling system is pressurized to 18 psi. to increase coolant boiling point which adds 9 degrees Fahrenheit to the boiling point of the coolant.
Coolant is also used to avoid corrosion.