1. Copyright © Cengage Learning. All rights reserved.1
Functions and Their Graphs
Copyright © Cengage Learning. All rights reserved.

2. Copyright © Cengage Learning. All rights reserved.
1.9
Inverse Functions
Copyright © Cengage Learning. All rights reserved.

3. Objectives
Find inverse functions informally and verify that two functions are inverse functions of each other.
Use graphs of functions to determine whether functions have inverse functions.
Use the Horizontal Line Test to determine whether functions are one-to-one.
Find inverse functions algebraically.

4. Inverse Functions

5. Inverse Functions
We know that a set of ordered pairs can represent a function. For instance, the function f (x) = x + 4 from the set A = {1, 2, 3, 4} to the set B = {5, 6, 7, 8} can be written as follows. f (x) = x + 4: {(1, 5), (2, 6), (3, 7), (4, 8)} In this case, by interchanging the first and second coordinates of each of these ordered pairs, you can form the inverse function of f, which is denoted by f –1.

6. Inverse Functions
It is a function from the set B to the set A, and can be written as follows. f –1(x) = x – 4: {(5, 1), (6, 2), (7, 3), (8, 4)} Note that the domain of f is equal to the range of f –1, and vice versa, as shown in figure below. Also note that the functions f and f –1 have the effect of “undoing” each other.

7. Inverse Functions
In other words, when you form the composition of f with f –1 or the composition of f –1 with f, you obtain the identity function. f (f –1(x)) = f (x – 4) = (x – 4) + 4 = x f –1(f (x)) = f –1(x + 4) = (x + 4) – 4 = x

8. Example 1 – Finding an Inverse Function Informally
Find the inverse of f (x) = 4x. Then verify that both f (f –1(x)) and f –1(f (x)) are equal to the identity function. Solution: The function f multiplies each input by 4. To “undo” this function, you need to divide each input by 4. So, the inverse function of f (x) = 4x is

9. Example 1 – Solution
cont’d
Verify that f (f –1(x)) = x and f –1(f (x)) = x as follows.

10. Inverse Functions

11. Inverse Functions
Do not be confused by the use of –1 to denote the inverse function f –1. In this text, whenever f –1 is written, it always refers to the inverse function of the function f and not to the reciprocal of f (x). If the function g is the inverse function of the function f, then it must also be true that the function f is the inverse function of the function g. For this reason, you can say that the functions f and g are inverse functions of each other.

12. The Graph of an Inverse Function

13. The Graph of an Inverse Function
The graphs of a function f and its inverse function f –1 are related to each other in the following way. If the point (a, b) lies on the graph of f, then the point (b, a) must lie on the graph of f –1, and vice versa. This means that the graph of f –1 is a reflection of the graph of f in the line y = x, as shown in Figure 1.58.
Figure 1.58

14. Example 3 – Verifying Inverse Functions Graphically
Sketch the graphs of the inverse functions f (x) = 2x – 3 and on the same rectangular coordinate system and show that the graphs are reflections of each other in the line y = x.

15. Example 3 – Solution
The graphs of f and f –1 are shown in Figure 1.59.
It appears that the graphs are reflections of each other in the line y = x. You can further verify this reflective property by testing a few points on each graph.
Figure 1.59

16. Example 3 – Solution
cont’d
Note in the following list that if the point (a, b) is on the graph of f, the point (b, a) is on the graph of f –1. Graph of f (x) = 2x – 3 Graph of (–1, –5) (–5, –1) (0, –3) (–3, 0) (1, –1) (–1, 1) (2, 1) (1, 2) (3, 3) (3, 3)

17. One-to-One Functions

18. One-to-One Functions
The reflective property of the graphs of inverse functions gives you a geometric test for determining whether a function has an inverse function. This test is called the Horizontal Line Test for inverse functions.

19. One-to-One Functions
If no horizontal line intersects the graph of f at more than one point, then no y-value is matched with more than one x-value. This is the essential characteristic of what are called one-to-one functions.

20. One-to-One Functions
Consider the function given by f (x) = x2. The table on the left is a table of values for f (x) = x2. The table on the right is the same as the table on the left but with the values in the columns interchanged.

21. One-to-One Functions
The table on the right does not represent a function because the input x = 4, for instance, matched with two different outputs: y = –2 and y = 2. So, f (x) = x2 is not one-to-one and does not have an inverse function.

22. Example 5(a) – Applying the Horizontal Line Test
The graph of the function f (x) = x3 – 1 is shown in Figure Because no horizontal line intersects the graph of f at more than one point, f is a one-to-one function and does have an inverse function.
Figure 1.61

23. Example 5(b) – Applying the Horizontal Line Test
cont’d
The graph of the function f (x) = x2 – 1 is shown in Figure Because it is possible to find a horizontal line that intersects the graph of f at more than one point, f is not a one-to-one function and does not have an inverse function.
Figure 1.62

24. Finding Inverse Functions Algebraically

25. Finding Inverse Functions Algebraically
For relatively simple functions (such as the one in Example 1), you can find inverse functions by inspection. For more complicated functions, however, it is best to use the following guidelines. The key step in these guidelines is Step 3—interchanging the roles of x and y. This step corresponds to the fact that inverse functions have ordered pairs with the coordinates reversed.

26. Finding Inverse Functions Algebraically

27. Example 6 – Finding an Inverse Function Algebraically
Find the inverse function of . Solution: The graph of f is shown in Figure 1.63.
Figure 1.63

28. Example 6 – Solution
cont’d
This graph passes the Horizontal Line Test. So, you know that f is one-to-one and has an inverse function.
Write original function.
Replace f (x) by y.
Interchange x and y.
Multiply each side by 3y + 2.

29. Example 6 – Solution Check that f (f –1(x)) = x and f –1(f (x)) = x.
cont’d
Check that f (f –1(x)) = x and f –1(f (x)) = x.
Distributive Property
Collect terms with y.
Factor.
Solve for y.
Replace y by f –1 (x).