Presentation is loading. Please wait.

Presentation is loading. Please wait.

Injector Diagnostics Status

Published byCatherine Gilmore Modified over 5 years ago

Similar presentations

Presentation on theme: "Injector Diagnostics Status"— Presentation transcript:

1 Injector Diagnostics Status
LCLS DOE Review October 25, 2006 Henrik Loos Diagnostics overview Beam profile monitors Wire Scanners Transverse Cavity Toroids, BPMs, BLM see J. Frisch

2 LCLS Diagnostics Tasks
Charge Toroids (Gun, Inj, BC, Und) Faraday cups (Gun & Inj) Trajectory & energy Stripline BPMs (Gun, Inj, Linac) Cavity BPMs (Und) Profile monitors (Inj), compare position with alignment laser Transverse emittance & energy spread Wire scanners YAG screen (Gun, Inj) OTR screens (Inj, Linac) Bunch length Cherenkov radiators + streak camera (Gun) Transverse cavity + OTR (Inj, Linac) Coherent radiation power (BC) Slice measurements Horizontal emittance T-cavity + quad + OTR Vertical Emittance OTR in dispersive beam line + quad Energy spread T-cavity + OTR in dispersive beam line

3 LCLS Injector Diagnostics
YAG, FC YAG Toroid T-Cavity Phase Monitor Wire Scanner Toroid OTR Toroid OTR YAG

4 Diagnostics Through BC1
RF Gun & Solenoid L0a&L0b S-Band Linacs T-Cav Sec 29 Transverse RF Cavity Bunch-Compressor-1 (BPM, OTR, collimator) OTR & Wire Scanners Gun Spectrometer L1 S-Band Linac Wire Scanners + OTR 135 MeV 250 MeV TD-11 stopper X-Band RF Straight Ahead Spectrometer Bunch Length Diagnostics 40 m

5 Requirements for YAG & OTR Monitors
Name Location Hor. Beam Size (mm) Ver. Beam Size (mm) Resol. (µm) YAG01 GTL 1.400 [7.0] [6.0] 15 YAG02 0.460 YAG03 L0 0.410 YAGG1 3.340 [45.0] 1.500 [8.0] 30 YAGS1 SAB 0.030 0.060 YAGS2 [10.0] 0.100 [12.0] OTRH1 DL1 0.180 0.380 40 OTRH2 0.200 0.280 OTR1,3 0.125 0.130 OTR2 0.065 OTR4 0.160 [1.5] 0.120 [14.0] 25 OTRS1 7 Name Location Hor. Beam Size (mm) Ver. Beam Size (mm) Resol. (µm) OTR11 BC1 3.800 0.100 30 OTR12 0.040 1.000 13 OTR21 BC2 2.600 0.050 16 OTRTCAV L3 0.070 [1.0] OTR30 DL2 0.010 [0.2] 0.025 3 OTR33 OTRDMP Dump 0.075 0.060 [0.6] 20 Large 50mm crystal required for gun spectrometer. Zoom lens needed. Requires foil with and angle of 5 deg to the beam and a likewise tilted camera to keep the entire screen in focus. Very high resolution required. Special optics design needs to be developed.

6 Beam Profile Monitor Specifications
YAG screens High yield at low energy 108 Photons at 5pC 100µm to meet resolution Saturation at high charge densities Combined with Faraday cup in GTL -> camera shielding Thin mirror (1mm) at higher energies OTR screens Small yield Aluminum foil 1µm Mitigates radiation issue Foil damage is concern Limited z-space Foil at 45 degree Depth of field ~1mm Match reflection direction with TCAV or dispersion direction OTR yield for 100mrad angular acceptance Energy (MeV) QE (%), nm 135 0.44 4300 0.98 13500 1.17

7 Optics Layout Used for all standard YAG/OTR screens Telecentric lens
Vacuum Filters Lens CCD OTR e-beam Reticule YAG Beam splitter Illumination Used for all standard YAG/OTR screens Telecentric lens 55mm focal length >100 line pairs/mm Magnification up to 1:1 Stack of 2 insertable neutral density filters Beam splitter and reticule for in situ calibration Megapixel CCD with 12bit and 4.6µm pixel size Radiation shielding in gun region

8 OTR/YAG Optics Design Actuator Optics Box CCD Screen Lens Filters Beam
Splitter Reticle Courtesy V. Srinivasan

9 OTR Profile Monitors

10 OTR Imager for Spectrometer
Need wide field of view in focus for measurements in spectrometer beam line Tilt OTR screen and CCD by 5 degrees in 1:1 imaging 12um resolution tested Device ready to install B.X. Wang et al. PAC05

11 Simulation of OTR Beam Size Measurement
Simulation of CCD image Include 0.5% TR yield, photon shot noise, and typical CCD parameters for quantum efficiency, read out noise, pixel size, digitizer gain Calculation of beam size Generate beam profile with 10σ bounding box Compare rms width of profile with original Gaussian beam size Simulation agrees well with OTR measurement at GTF Error of 5% in beam size for beam of 0.1nC, 260µm at 10µm resolution Q = 0.1nC E = 135 MeV

12 YAG Efficiency Nφ = 14µm-1 l sin2(θ/2)
YAGG1 beam image at 5 pC Nφ = 14µm-1 l sin2(θ/2) l = 0.1mm, θ = 70mrad, Nφ = 1.7/e- 1nC: Nφ = 1*1010 200pC: Nφ = 2*109 5pC: Nφ = 5*107

13 CCD Camera and Lens Test
Uniq Vision CCD Dark Image Test TECM55 lens with ruler (scale 1/64”) Periodic BG structure removed with background subtraction Resolution: B/W transition < 20um

14 Profile Monitor Controls
x CCD Image YAG Crystal Rows y Rate limit electron beam Single bunch & burst mode Prevent foil damage and limit camera irradiation Camera control Cameralink and EPICS IOC Buffered Screen Image processing Flip image to match image coordinates with beam Background subtraction Automated image cropping Beam size calculation Different algorithms Gaussian fit Baseline cut, etc. Mock-up

15 Software Development

16 Profile Monitor Commissioning Tasks
Verify correct image polarity and calibration. Compare with alignment laser, BPMs and wire scanners. Find proper attenuation filter for YAG profile monitors. Determine beam center with alignment laser.

17 Wire Scanner Status Requirements Hardware status Software status
Step size 5um Accuracy 2um, reproducibility 10um Tungsten wire 20um to 60um, matched to beam size Hardware status Wire scanners for injector tested to meet specs and calibrated Photomultipliers with charge integrating ADCs tested Software status Low level EPICS Calibration tool Scan user interface to select 1 or more wires Buffered acquisition linked to timing system High level Matlab Software for normalization with toroid and jitter correction with BPM to be completed in November Profile analysis and emittance calculation same as for profile monitors

18 Requirements Area IN20 LI21 LI24 LI27 LI28 LTU Total Scanners 4 3 1 19

19 Distance Measurement (LVDT or similar)
Design - Mechanical Distance Measurement (LVDT or similar) Motor Beam Limit Switches

20 Current Status

21 User Interface - Operations

22 Transverse Cavity Bunch Length Measurement
TCAV in 135 MeV Low field of 1.4 MV sufficient Invasive measurements on OTR2, 4, S1, YAGS2 TCAV in Sector 25 at 5.9 GeV Max field of 25 MV Parasitic measurement with horizontal kicker and off-axis OTR Horizontal Kicker Vertical Deflecting Cavity Off-axis Screen Electron Beam

23 Injector TCAV TCAV tested successfully at full gradient in klystron lab 3MW, 120Hz, 3us pulse 2MW, 120Hz, 3us pulse was requirement

24 Transverse Cavity Calibration
Temporal resolution limited by beta function, RF power, screen size Calibration with TCAV phase scan Calibration accuracy limited by phase jitter TCAV injector: >>20 slices possible TCAV linac: <5 slices due to limited RF, non-dedicated optics, screen resolution Mock-up Mock-up

25 Software Development

26 Commissioning Readiness
Redundancy in diagnostics, independent methods to determine the most important beam parameters Before commissioning check-out of each device by physicist to verify proper functioning and correct assignment in control system

Download ppt "Injector Diagnostics Status"

Similar presentations

Christopher Gerth, Michael Röhrs, Holger Schlarb DESY Hamburg Optics for Diagnostic Section BC1 in the European XFEL.

Christopher Gerth, Michael Röhrs, Holger Schlarb DESY Hamburg Optics for Diagnostic Section BC1 in the European XFEL.
Paul Emma LCLS FAC April 16, 2006 1 Initial Experience with Injector Commissioning P. Emma, et al. Facilities Advisory Committee.

Paul Emma LCLS FAC April 16, Initial Experience with Injector Commissioning P. Emma, et al. Facilities Advisory Committee.
P. Emma, SLACLCLS Commissioning – Sep. 22, 2004 Linac Commissioning P. Emma LCLS Commissioning Workshop, SLAC Sep. 22-23, 2004 LCLS.

P. Emma, SLACLCLS Commissioning – Sep. 22, 2004 Linac Commissioning P. Emma LCLS Commissioning Workshop, SLAC Sep , 2004 LCLS.
P. Emma, SLACLCLS FAC Meeting - April 29, 2004 Linac Physics, Diagnostics, and Commissioning Strategy P. Emma LCLS FAC Meeting April 29, 2004 LCLS.

P. Emma, SLACLCLS FAC Meeting - April 29, 2004 Linac Physics, Diagnostics, and Commissioning Strategy P. Emma LCLS FAC Meeting April 29, 2004 LCLS.
Hamid Shoaee LCLS FAC Review – October 2007 1 Control System Overview Hamid Shoaee Controls System Manager Injector control system commissioning & Support.

Hamid Shoaee LCLS FAC Review – October Control System Overview Hamid Shoaee Controls System Manager Injector control system commissioning & Support.
Cecile Limborg-Deprey Injector Commissioning September 22 2004 Injector Commissioning Plans C.Limborg-Deprey Gun exit measurements.

Cecile Limborg-Deprey Injector Commissioning September Injector Commissioning Plans C.Limborg-Deprey Gun exit measurements.
Henrik Loos High Level 17 June 2008 High Level Physics Applications for LCLS Commissioning Henrik Loos.

Henrik Loos High Level 17 June 2008 High Level Physics Applications for LCLS Commissioning Henrik Loos.
Cecile Limborg-Deprey Injector October 12 2004 Injector Physics C.Limborg-Deprey Diagnostics and Commissioning GTL measurements.

Cecile Limborg-Deprey Injector October Injector Physics C.Limborg-Deprey Diagnostics and Commissioning GTL measurements.
F Specifications for the dark current kicker for the NML test facility at Fermilab S. Nagaitsev, M. Church, P. Piot, C.Y. Tan, J. Steimel Fermilab May.

F Specifications for the dark current kicker for the NML test facility at Fermilab S. Nagaitsev, M. Church, P. Piot, C.Y. Tan, J. Steimel Fermilab May.
Injector Accelerator Readiness Review, 10/31/06 Henrik Loos 1 Beam Losses During LCLS Injector Phase-1 Operation Scope of phase 1 operation Operating modes.

Injector Accelerator Readiness Review, 10/31/06 Henrik Loos 1 Beam Losses During LCLS Injector Phase-1 Operation Scope of phase 1 operation Operating modes.
Low Emittance RF Gun Developments for PAL-XFEL

Low Emittance RF Gun Developments for PAL-XFEL
~10 18 57 4 61 gun3.9 GHz cavity Bunch compressor 3 ILC cryomodules 45 deg. spectro injector main linac user area disp. area transport line Overview of.

~ gun3.9 GHz cavity Bunch compressor 3 ILC cryomodules 45 deg. spectro injector main linac user area disp. area transport line Overview of.
SPPS, Beam stability and pulse-to-pulse jitter Patrick Krejcik For the SPPS collaboration Zeuthen Workshop on Start-to-End Simulations of X-ray FEL’s August.

SPPS, Beam stability and pulse-to-pulse jitter Patrick Krejcik For the SPPS collaboration Zeuthen Workshop on Start-to-End Simulations of X-ray FEL’s August.
LCLS Accelerator SLAC linac tunnel research yard Linac-0 L =6 m Linac-1 L  9 m  rf   25° Linac-2 L  330 m  rf   41° Linac-3 L  550 m  rf  0°

LCLS Accelerator SLAC linac tunnel research yard Linac-0 L =6 m Linac-1 L  9 m  rf   25° Linac-2 L  330 m  rf   41° Linac-3 L  550 m  rf  0°
Recent Experiments at PITZ ICFA Future Light Sources Sub-Panel Mini Workshop on Start-to-End Simulations of X-RAY FELs August 18-22, 2003 at DESY-Zeuthen,

Recent Experiments at PITZ ICFA Future Light Sources Sub-Panel Mini Workshop on Start-to-End Simulations of X-RAY FELs August 18-22, 2003 at DESY-Zeuthen,
Electron Source Configuration Axel Brachmann - SLAC - Jan. 19 2006, KEK GDE meeting International Linear Collider at Stanford Linear Accelerator Center.

Electron Source Configuration Axel Brachmann - SLAC - Jan , KEK GDE meeting International Linear Collider at Stanford Linear Accelerator Center.
1 Henrik Loos 1 13 Sep 2011 APE Meeting Recent Activities H. Loos 09/13/2011.

1 Henrik Loos 1 13 Sep 2011 APE Meeting Recent Activities H. Loos 09/13/2011.
W.S. Graves 2002 Berlin CSR workshop 1 Microbunching and CSR experiments at BNL’s Source Development Lab William S. Graves ICFA CSR Workshop Berlin, Jan.,

W.S. Graves 2002 Berlin CSR workshop 1 Microbunching and CSR experiments at BNL’s Source Development Lab William S. Graves ICFA CSR Workshop Berlin, Jan.,
Henrik Loos LCLS ICW 2006 10 October 2006 Diagnostics in the LCLS LCLS Injector Commissioning Workshop October 9-11, 2006 Henrik.

Henrik Loos LCLS ICW October 2006 Diagnostics in the LCLS LCLS Injector Commissioning Workshop October 9-11, 2006 Henrik.
Construction, Commissioning, and Operation of Injector Test Facility (ITF) for the PAL-XFEL November 12, 2013 S. J. Park, J. H. Hong, C. K. Min, I. Y.

Construction, Commissioning, and Operation of Injector Test Facility (ITF) for the PAL-XFEL November 12, 2013 S. J. Park, J. H. Hong, C. K. Min, I. Y.

Similar presentations

Ads by Google