1. ODF Seal Material

2. Summery
If entire Kyoritsu’s ideas are accepted in ODF process,
- Reduce mask process
- Make design flexibility in LCD
- Make high quality device
If Kyoritsu’s support are accepted in your compnay,
- Provide RCA to technical issue by accumulation of technology and knowledge.
- Productivity & provide cost down.
- Improve TSD’s design to G10.

3. ODF Process Information If you doesn’t use “Yellow lamp room” …
Dispensing seal material
LC drop
Lamination
GAP control
Masking
UV curing
Room: Yellow Lamp
Room: Yellow Lamp
Room: Yellow Lamp
Room: Yellow Lamp
Room: Yellow Lamp
Room: Yellow Lamp
Process condition
Air
Air
Vacuum
Vacuum
Air
Air
Air
Using ODF’s needle
Mask release
Heat curing
Complete
Information
If you doesn’t use “Yellow lamp room” …
- Cannot controlling GAP
- It has possibility to occur needle clogging by cured adhesive
Room: Yellow Lamp
Room: Yellow Lamp
Room: Yellow Lamp
If you can use wavelength at over 400nm, it can without masking
Air
Air
Air
Process condition

4. Technical Information of Kyoritsu Typical Material @ 723K1
VHR data (%T)
Feature
Solving to display defect issue
- Low elution (good light distribution) / Good electrical characteristics
Improving reliability
- Good adhesion to Glass and PI / Accept shadow area curing
TDS
　Product Name
723K1
Condition
Color
Liquid
Yellow
Visual Contact
Main Component
Epoxy Acrylate
One Component
Viscosity
~ mPa･s ~
298,800
Cone / Plate　
Cure Condition UV ＋
Heat
2,000 mJ/cm2 +
120C×60min
UV: 340 ~ 440 nm
Hardness
~ Shore ~
D 87
Hardness Meter　
Water Vapor Transmission Rate
g/m2・24hr
24.4
65℃ / 95%
Weight Loss by Heating %
under 1.5
TG, 120C×60min
Extract Water Solution Conductivity
μS/cm
32.5
PCT 121C×20h
Extract Water pH pH
4.19 Tg
~ C ~
110.5
TMA method 0.5mmt
Pot Life
Time
24 h
At Room Temperature
Guaranteed Condition C
under -15
At Dark Place
Guaranteed Term
month 6
After Manufacturing
Validation result
Ion Density data (pC / cm2)

5. Device Design Candidate
Type 1
Type 2
Polarizer
Polarizer
OCA
OCA
Glass
Glass
CF + BM BM BM
CF + BM BM BM
ITO
Seal PI
Seal
Seal PI
Seal LC LC PI PI
TFT
TFT
Glass
Glass
OCA
OCA
Polarizer
Polarizer
Back Light
Back Light

6. Seal Design Candidate ① w/ PI Lap Need adhesion to PI PI design
② w/o PI Lap
Need adhesion to ITO
Seal dimension
Apply design
After Lamination design

7. Material Decision Flow
Propose
Simulation
Workability
test
Initial Test
Panel Test
Assembly
test
Material
Qualification
PP 1
in INDIA
Material
Qualification
PP 2
in INDIA MP
Viscosity
Stirring
condition
LC Compatibility
Temp.
shock
MURA
Adhesion
Apply
condition
Electrical
High Temp
& Humidity 2
MPB
Cleaning
condition
Adhesion
Elution 3 Tg 4 4 4 4
Cure
condition 5 5 5 5

8. Notes JAPAN Overseas - 15C FREEZE FREEZE FREEZE DEFORST or
≪Temperature≫
Yellow Lamp
JAPAN
Overseas
- 15C
FREEZE
FREEZE
FREEZE
DEFORST
- Bottle Open
- Using
KYORITSU
Trading Company-1 or
Trading Company-2
Your company
worker
≪Add spacer & Refill Process≫
Viscosity change after stirring
Yellow Lamp
* 37 C or 40 C ⇒ 25C
Bottle 300ml
Stirrer
Syringe
(Add spacer)
Refill
Validation result
KYORITSU
Your company

9. Notes-2 ≪Dispenser Needle≫
Cleaning Process
Remove adhesive with a Air blow
Ultrasonic 15min × 3 times
Flowing by pure acetone
Air drying
*Solvent is acetone

10. Thank you very much for your attention and interested!