Presentation is loading. Please wait.

Presentation is loading. Please wait.

Spectrometer Solenoid Update

Published byElisabet Penttilä Modified over 5 years ago

Similar presentations

Presentation on theme: "Spectrometer Solenoid Update"— Presentation transcript:

1 Spectrometer Solenoid Update
MICE Collaboration Meeting #30 Oxford University Steve Virostek Lawrence Berkeley National Lab July 6, 2011

2 Topics Spectrometer Solenoid workshop at LBNL Design modifications
Magnet quench analyses Quench resistor overheating Schedule, budget and manpower Current progress

3 MICE Cooling Channel Layout
Spectrometer Solenoid #1 Spectrometer Solenoid #2

4 Spectrometer Solenoid Workshop at LBNL
A workshop was held at LBNL in early May to assess the current design of the magnet, to review the recent analyses and to evaluate the proposed design modifications The following personnel participated in person at the workshop: RAL: Andy Nichols, Mike Courthold, Roy Preece INFN: Pasquale Fabbricatore FNAL: Alan Bross, Vladimir Kashikhin MIT: Brad Smith, Joe Minervini, Alexey Radovinsky SINAP: Wang Li LBNL: Steve Gourlay, Mike Zisman, Steve Virostek, Derun Li, Heng Pan, Soren Prestemon, Allan DeMello, Tapio Niinikoski, John Joseph

5 Analysis and Design Assessment
LBNL has completed a series of tasks prior to incorporating design changes The steps carried out are shown below: All heat loads have been reassessed to ensure that the LHe in the cold mass can be maintained with the final number of cryocoolers EM calculations have been redone for testing and operation The instrumentation plan has been modified to allow confirmation of the thermal and EM calculations during testing The mechanical supports of the magnet, leads, piping and other internal components have been reassessed A complete set of the latest as-built drawings (w/current changes) has been compiled

6 Design Modification Plan
A design modification plan has been developed by LBNL and includes the following: - reduction of heat leaks to the cold mass - the addition of more cryo cooling power - assessment of the suitability of the passive quench protection system - adding a scheme to address the quench resistor overheating - modification of the LTS leads to prevent burn-out The finalization of the plan is still pending the confirmation of the quench analysis results Mechanical modifications are moving forward

7 4.2K Heat Load Reduction Improved vacuum pumping and instrumentation will be implemented to ensure adequate cold mass insulation All 4K areas will be covered with actively cooled shield where possible – partially covered areas will be analyzed Baffles will be added to the vent lines to prevent direct radiation shine to 4.2K Possible thermal acoustic oscillations in vent lines will be addressed by monitoring with fast pressure gauges Application of MLI on cold mass bore will be improved Sensor wires will be optimized & w/proper heat sinking

8 Radiation Shield Improvements
The radiation shields will be remade using 6.35 mm thick series aluminum to replace the existing 6061 aluminum shields The thermal connection between the cooler first stage and the radiation shield will be improved by using sheets of copper rather than tubes of aluminum Reduced compression on shield bore tube MLI The following heat loads will be decreased as possible: cold mass supports shield pass-through holes, intermediate cold mass support heat intercepts, shielding of support warm ends Currently analyzing increased eddy current forces due to lower resistivity material

9 New Rolled Shields at Wang NMR
Highlights * UHV Tunable Windows, or grids

10 Other Design Modifications
Other key improvements: The total cooling power will be increased by using five 2-stage pulsed tube coolers and one single-stage cooler The thermal/mechanical stabilities of the cold leads will be improved by adding extra copper/superconductor near the cold mass feedthroughs Other improvements/additions: LBNL/MICE personnel will be present to document and oversee all aspects of magnet reassembly Detailed MLI inspection will be carried out during ass’y A fast DAQ system will continuously monitor voltage taps Additional temperature sensors will be added to the logging system

11 5 + 1 Cryocooler Layout

12 Magnet 2B Cold Lead Repair
Highlights * UHV Tunable Windows, or grids

13 Instrumentation Plan The current configuration of the instrumentation on the spectrometer solenoid magnets has been revised The instrumentation under consideration includes temperature sensors, voltage taps, helium level gages, and pressure gages In most cases, the proposed changes to the instrumentation scheme came about due to shortcomings that were identified during the previous rounds of magnet training and testing Another prime consideration is the ability to record data relevant to the confirmation of our heat load analyses Feedthroughs have been reconfigured to separate the various types of instrumentation Highlights * UHV Tunable Windows, or grids

14 Fabrication Drawings Nearly 200 detail fabrication drawings representing the latest assembly of the Spectrometer Solenoid (Magnet 2B) collected from Wang NMR Drawings have been organized in the form of a drawing tree list The drawings are a fairly complete representation of the previously as-built magnet Wang NMR has completed the update of the fabrication drawings to reflect the latest design changes In parallel with the effort to organize the drawings, LBNL has developed a preliminary 3D CAD model of the magnets The CAD model will be updated to reflect the as-built magnets Highlights * UHV Tunable Windows, or grids

15 Electromagnetic Assessment
The design of the passive magnet protection system has been reviewed and analyzed under the various operational regimes The areas covered include calculation of the magnet self and mutual inductance parameters determination of the coil current decay versus time during a quench calculation of the hot spot temperature in the magnet for different scenarios analysis of coil voltage versus time during a quench Overheating of the quench resistors has been analyzed and a cooling scheme has been devised and tested Highlights * UHV Tunable Windows, or grids

16 Spectrometer Solenoid 3D EM Model

17 Quench Modeling VF quench code:
Allows simulation of… Quenchback (e.g. from Al. mandrel) Various circuit configurations Provides access to… Temperature and voltage evolution in time and space Current distribution and decay Example circuit of spectrometer test sim. Quenching coil Superconducting coils Distribution of field

18 Internal Quench Protection Circuitry
Need to protect resistors from Open circuit Low-current quench => need to sink resistors Preferably to mandrel nearby: large heat capacity, access all helium, induce coil quenches

19 Resistor Cooling Scheme
The design provides a path for thermal transport from the resistors to the cold mass: Simple design that minimizes risk to resistors Avoids shorts and significant deformations while allowing resistors to flex Capable of transferring ~2kW DC with dT=300K

20 Resistor Cooling Test at LBNL

21 Overall Quench System Plan
Finish test of bypass resistor cooling scheme (now complete) Demonstrated reduction in peak temperature Demonstrated no electrical shorts under cycling Implement resistor cooling scheme on spectrometer solenoids Finalize all 3D simulations with detailed engineering note Find sources of the few remaining discrepancies between the different quench models Implement strict controls: Temperature limits on HTS leads Automate PS shut-off based on quench voltage signals Give serious consideration to adding active protection Weigh pros and cons – evaluate risks

22 Schedule, Budget and Manpower
A detailed straw man schedule has been assembled based on LBNL experience that provides a compilation of the tasks with an estimate of the required durations A resource loaded schedule is being developed in conjunction with Wang NMR – 1st magnet to be tested by the end of 2011 An estimate of the remaining costs to MAP to complete the Spectrometer Solenoids has been compiled, including both manpower and hardware Contingency was estimated to account for uncertainties, including the possible need for active quench protection Required manpower has been identified and is available

23 Manpower The following individuals are part of the Spectrometer Solenoid team: Steve Gourlay – LBNL AFRD Division Director - LBNL technical contact for Spectrometer Solenoid and Coupling Coil magnets - oversight of the LBNL Spectrometer Solenoid team - contact for the DOE Office of High Energy Physics Steve Virostek - Sr. Mechanical Engineer - overall project management some oversight of magnet assembly and training - documentation Tapio Niinikoski - Sr. Cryogenic Engineer - CERN retiree, hired 1/2 time by LBNL magnet design analysis and modification - some oversight of magnet assembly and training magnet training oversight Dennis Calais - Cryogenic Technician on site at Wang NMR during assembly Mainly working on instrumentation and cryocoolers Roy Preece - Mechanical Engineer (RAL) - oversight of magnet assembly - magnet training oversight - integration and documentation Nanyang Li - Mechanical Engineer - documentation Soren Prestemon - Cryogenic Engineer - magnet design analysis - design modification recommendations - occasional oversight of magnet assy Heng Pan - Cryogenic Postdoc - quench analysis - radiation shield eddy current and force analysis

24 Latest Magnet Progress
A PO change order was issued to Wang NMR to complete the layout and detailed design of the modified magnet mechanical design – this work has been completed and a small review held at Wang NMR The 5+1 cooler layout has been completed Both radiation shields will be remade from scratch using 6.35 mm thick 1100 series aluminum (material rec’d and rolling is complete) The cold mass vent lines are being enlarged and radiation light baffles are being added The magnet instrumentation plan and feedthrough layout have been updated and sensors and feedthroughs have been ordered A second change to the PO for actual modifications to be placed soon The final modification plans still have to be presented to MAP and the MICE Tech Board Highlights * UHV Tunable Windows, or grids

Download ppt "Spectrometer Solenoid Update"

Similar presentations

MICE RF and Coupling Coil Module Outstanding Issues Steve Virostek Lawrence Berkeley National Laboratory MICE Collaboration Meeting October 26, 2004.

MICE RF and Coupling Coil Module Outstanding Issues Steve Virostek Lawrence Berkeley National Laboratory MICE Collaboration Meeting October 26, 2004.
MICE Coupling Coil Testing at Fermilab MICE Collaboration Meeting Ruben Carcagno March 15, 2012 1R. Carcagno - MICE CC Testing at Fermilab3/15/2012.

MICE Coupling Coil Testing at Fermilab MICE Collaboration Meeting Ruben Carcagno March 15, R. Carcagno - MICE CC Testing at Fermilab3/15/2012.
Power Supply System John Joseph LBNL Spectrometer Solenoid Test Plan Review Feb 17 th 2012.

Power Supply System John Joseph LBNL Spectrometer Solenoid Test Plan Review Feb 17 th 2012.
Magnet quench during a training run Magnet electrical circuit schematic PROGRESS ON THE MODELING AND MODIFICATION OF THE MICE SUPERCONDUCTING SPECTROMETER.

Magnet quench during a training run Magnet electrical circuit schematic PROGRESS ON THE MODELING AND MODIFICATION OF THE MICE SUPERCONDUCTING SPECTROMETER.
Spectrometer Solenoids MICO 146 Steve Virostek LBNL June 6, 2011.

Spectrometer Solenoids MICO 146 Steve Virostek LBNL June 6, 2011.
Trip Report on the visit to ICST of HIT, Harbin, China Derun Li Mike Green Steve Virostek Mike Zisman Lawrence Berkeley National Laboratory (from December.

Trip Report on the visit to ICST of HIT, Harbin, China Derun Li Mike Green Steve Virostek Mike Zisman Lawrence Berkeley National Laboratory (from December.
Spectrometer Solenoid Update Steve Virostek Lawrence Berkeley National Lab MICE Video Conference 114 September 18, 2008.

Spectrometer Solenoid Update Steve Virostek Lawrence Berkeley National Lab MICE Video Conference 114 September 18, 2008.
Spectrometer Solenoid Design and Procurement Review Steve Virostek Mike Green Mike Zisman Lawrence Berkeley National Lab MICE Collaboration Meeting October.

Spectrometer Solenoid Design and Procurement Review Steve Virostek Mike Green Mike Zisman Lawrence Berkeley National Lab MICE Collaboration Meeting October.
23 October 2005MICE Meeting at RAL1 MICE Tracker Magnets, 4 K Coolers, and Magnet Coupling during a Quench Michael A. Green Lawrence Berkeley Laboratory.

23 October 2005MICE Meeting at RAL1 MICE Tracker Magnets, 4 K Coolers, and Magnet Coupling during a Quench Michael A. Green Lawrence Berkeley Laboratory.
1 Spectrometer Solenoid Design and Cost Update Michael A. Green Lawrence Berkeley Laboratory 10 February 2005.

1 Spectrometer Solenoid Design and Cost Update Michael A. Green Lawrence Berkeley Laboratory 10 February 2005.
MICE RF Module Safety Steve Virostek Lawrence Berkeley National Laboratory MICE Collaboration Meeting February 12, 2005.

MICE RF Module Safety Steve Virostek Lawrence Berkeley National Laboratory MICE Collaboration Meeting February 12, 2005.
Spectrometer Solenoid Fabrication Update Steve Virostek Lawrence Berkeley National Lab MICE CM23 at ICST, Harbin January 14, 2009.

Spectrometer Solenoid Fabrication Update Steve Virostek Lawrence Berkeley National Lab MICE CM23 at ICST, Harbin January 14, 2009.
Spectrometer Solenoid Update Steve Virostek - LBNL MICE Video Conference #129 February 25, 2010.

Spectrometer Solenoid Update Steve Virostek - LBNL MICE Video Conference #129 February 25, 2010.
9 June 2006MICE CM-15 Fermilab1 Progress on the MICE Cooling Channel and Tracker Magnets since CM-14 Michael A. Green Lawrence Berkeley Laboratory.

9 June 2006MICE CM-15 Fermilab1 Progress on the MICE Cooling Channel and Tracker Magnets since CM-14 Michael A. Green Lawrence Berkeley Laboratory.
1 The Genoa Tracker Solenoids and their Contribution toward a New Design Michael A. Green Lawrence Berkeley National Laboratory and Pasquale Fabbricatore.

1 The Genoa Tracker Solenoids and their Contribution toward a New Design Michael A. Green Lawrence Berkeley National Laboratory and Pasquale Fabbricatore.
1 MICE Funding Agency Committee PM report Overview Organisation and project management Schedule reconstruction The Step IV subsystems Andy Nichols, STFC,

1 MICE Funding Agency Committee PM report Overview Organisation and project management Schedule reconstruction The Step IV subsystems Andy Nichols, STFC,
Spectrometer Solenoid Update Steve Virostek - LBNL MICE Video Conference #145 December 15, 2011.

Spectrometer Solenoid Update Steve Virostek - LBNL MICE Video Conference #145 December 15, 2011.
Spectrometer Solenoid Fabrication & Testing Update Steve Virostek Lawrence Berkeley National Lab MICE CM24 at RAL June 1, 2009.

Spectrometer Solenoid Fabrication & Testing Update Steve Virostek Lawrence Berkeley National Lab MICE CM24 at RAL June 1, 2009.
Update Hardware for conductive cooling of the quench resistors has been fabricated at LBNL. Preparation for installation to start this week. Installation.

Update Hardware for conductive cooling of the quench resistors has been fabricated at LBNL. Preparation for installation to start this week. Installation.
Spectrometer Solenoid and RFCC Update Michael S. Zisman Center for Beam Physics Accelerator & Fusion Research Division Lawrence Berkeley National Laboratory.

Spectrometer Solenoid and RFCC Update Michael S. Zisman Center for Beam Physics Accelerator & Fusion Research Division Lawrence Berkeley National Laboratory.

Similar presentations

Ads by Google