1. KX-NS1000 Step by Step Guide PBX to PBX One-look Network Stacking Card
June 20, 2014
Panasonic System Networks PBX SE team
Specifications are subject to change without notice. 1

2. 1. Introduction
KX-NS1000 one-look networking supports full feature transparency like TDE600-TDE620 connection. - Max.16 KX-NS1000 can be connected for one-look connection. - Max. 1,000 extensions are supported by one-look networking. - Both master unit and slave unit are “KX-NS1000”. - Slave unit has to be registered to master unit like IP-PT registration. Programming is very easy because it is same as IP-PT registration.
TDE620 is connected with TDE600 by cable.
Master Register Slave Max. 15 slave NS1000 can be registered to one master NS1000.
Digital PT IP-PT Digital PT is connected with PBX by cable. IP-PT is registered to PBX.
CO Fukuoka
IP Network
IP Network (VPN)
CO Tokyo
Register .　
CO Niseko

3. 2. Indicator The PBX mode (Master or Slave) is indicated by LED.
Indicators
<Master Unit>
<Slave Unit>
Software version and suffix such as “BX” have to be same for both main unit and slave unit.
BATT
ALARM
MASTER 3

4. 3. Stacking Card with one-look networking
You can connect a maximum of 2 existing PBXs for one KX-NS1000. A maximum of 8 existing PBXs and 16 KX-NS1000 can be connected for the entire One-look Network. They support 1,000 extensions. An existing PBX refers to a Panasonic KX-TDE series, KX-NCP series, or KX-TDA100/200/600/620 PBX.
IP Network
KX-TDE620
Stacking
Stacking
KX-TDE600
KX-TDE620
KX-TDE600
KX-NCP
Max. 8 PBXs
IP Network
Stacking
Stacking
KX-NCP
Stacking
QSIG
100 % Feature Transparency like TDE600 and TDE620
KX-DT
KX-DT
KX-DT
KX-DT
KX-DT
KX-DT
Different PBX category cannot be mixed to one KX-NS Category 1 : KX-NCP Category 2 : KX-TDE(A) Category 3 : KX-TDE(A) Category 4 : KX-TDA100D
NCP500+TDE200 : N/A TDE100+TDA200 : OK TDE600+TDE620 : OK TDE620+TDE620 : OK
Programming is not required to connect stacking card. 4

5. 4. Table of Contents Chapter Explanation 1
Activation key installation to Master PBX 2
Slave unit data assignment to Master PBX 3
Set-up Slave PBX Activation key installation to Slave PBX 4
Slave PBX registration to Master PBX 5
Demo after set-up 5

6. Activation key installation to Master PBX
Master Unit
Chapter 1
Activation key installation to Master PBX
Master Register Slave 6

7. 11. Trial Activation Key
Master Unit
Activate pre-installed trial activation key for One-look network. - Standard activation key has to be installed before expiration (60 days). 7

8. 12. Standard Activation Key
Master Unit
Install standard activation key for One-look network if trial activation key has been already expired. 8

9. Slave PBX data assignment to Master PBX
Master Unit
Chapter 2
Slave PBX data assignment to Master PBX
Master Register Slave 9

10. 21. Add Site Wizard
Master Unit
1. Click [Add Site]. 10

11. 22. Add Site Wizard
Master Unit
1. Select correct time zone and time of Slave PBX. 2. Click [Next]. 11

12. 23. Add Site Wizard 1. (Programming is not required.) 2. Click [Next].
Master Unit
1. (Programming is not required.) 2. Click [Next]. 12

13. 24. Add Site Wizard 1. (Programming is not required.) 2. Click [Next].
Master Unit
1. (Programming is not required.) 2. Click [Next]. 13

14. 25. Add Site Wizard
Master Unit
1. Select “No”. “No” is strongly recommended for demo of one-look network. If LAN is removed from slave PBX for example, back-up mode starts. Even if LAN is connected again, back-up mode is kept until operation to return to normal one-look mode. So demo of one-look network is not possible without this operation.
If demo of back-up is required, it can be assigned later. 14

15. 26. Change PBX Site Name
Master Unit
1. Click “List View”. 15

16. 27. Change PBX Site Name 1. Change site name and click [Apply].
Master Unit
1. Change site name and click [Apply]. 16

17. Setup Slave PBX Activation key to Slave PBX
Slave Unit
Chapter 3
Setup Slave PBX Activation key to Slave PBX
Master Register Slave 17

18. 31. Easy Setup Wizard
Slave Unit
Initialize KX-NS1000 Slave unit by default clear. If IP address of Master unit is , do not connect Slave unit in the same network because default of IP address is Connect PC with KX-NS1000 Slave unit.to start “Easy Setup Wizard”. 1
Location Setting Screen
1. Select “Slave” as a PBX type, and
specify the IP address of the Master. *
2. Click “Next”.
* If the slave is located on the same network with the Master, it is unnecessary to specify
the IP address of the Master.

19. 32. Easy Setup Wizard Slave Unit 2. PBX Setting Screen 2
Site name is fixed.
(Will be downloaded from the Master.)
2. Set Time Zone and Local Time of slave unit.
3. Click “Next”. 3
3. LAN Setting Screen
Set the LAN settings for the slave unit.
2. Click “Next”.

20. 33. Easy Setup Wizard
Slave Unit
4. Registration Setting Screen 4
1. Select “Active” to enable trial activation key for One-look networking.
Standard activation key has to be installed before expiration (60 days).
2. To finish the Easy setup wizard, click “Finish”.
3. To register to master unit, click “OK”. Registration mode of master unit has to start before or after this step. See chapter 4.

21. Slave PBX registration to Master PBX
Master Unit
Chapter 4
Slave PBX registration to Master PBX
Master Register Slave 21

22. 41. Register Slave unit
Master Unit
1. Click [Registration].

23. 42. Register Slave unit 1. Select slave unit and click [Next].
Master Unit
1. Select slave unit and click [Next].

24. 43. Register Slave unit 1. Connect Slave unit to LAN.
Master Unit
1. Connect Slave unit to LAN.
After registration is completed, the slave unit will reboot automatically. So wait for more 3 minutes.

25. 44. Register Slave unit
Master Unit
After 3 minutes, slave unit becomes In Service.
Home Screen
After registration
Before registration
List View Screen
PBX version and so on is displayed.

26. Chapter 5
Demo after setup 26

27. 51. Demo or test after setup
Paging to all extensions in Tokyo and Fukuoka.
KX-NS1000 Master (Tokyo)
KX-NS1000 Slave (Fukuoka)
DSP
Fax
DSP
NS0130 NS
DHLC8
KX-NT
Paging
Paging
Paging
Paging
KX-DT
*33 – Paging group number (01)
Cards in TDA/TDE/NCP are recognized automatically through KX-NS0130 without programming. User Group 1 (Paging group 1) has to be programmed to KX-NT to receive paging. Default is User Group 31.

28. Slave unit can be selected.
52. Slave Unit - Programming
Slave unit can be programmed from master unit.
Slave unit can be selected.
Master
Slave

29. 53. Stacking Card - Programming
Property of cards in TDA/TDE/NCP can be programmed using NS1000 Web.

30. 54. Site ID
Site ID is displayed to know location (Unit). - The “Site ID” is displayed for “CO Line Settings”, “DIL Table & port Settings”, “Doorphone”, “External Relay” and “External Sensor”.

31. 55. Direct Log-in to branch unit
Direct log-in is used to setup Built-in VM in slave unit. - After direct log-in, Web-MC logs-out from master PBX automatically.
Built-in VM : 500
Master
Built-in VM : 501
Slave
Built-in VM : 500
Master
Built-in VM : 501
Slave

32. Thank you !

33. Revision Date No. Change Sep 11 - First edition Mar 6 June 20
31 (Page 18)
Do not connect slave unit in the network before correct IP address is assigned to slave PBX. 33