Presentation is loading. Please wait.

Presentation is loading. Please wait.

Fig. 4 Scalable module illustration.

Published bySami Nurminen Modified over 5 years ago

Similar presentations

Presentation on theme: "Fig. 4 Scalable module illustration."— Presentation transcript:

1 Fig. 4 Scalable module illustration.
Scalable module illustration. One module consisting of 36 × 36 junctions placed on the supporting steel frame structure: Nine wafers containing the required DACs and control electronics are placed between the wafer holding 36 × 36 junctions and the microchannel cooler (red layer) providing the cooling. X-Y-Z piezo actuators are placed in the four corners on top of the steel frame, allowing for accurate alignment of the module. Flexible electric wires supply voltages, currents, and control signals to the DACs and control electronics, such as field-programmable gate arrays (FPGAs). Coolant is supplied to the microchannel cooler layer via two flexible steel tubes placed in the center of the modules. Bjoern Lekitsch et al. Sci Adv 2017;3:e Copyright © 2017, The Authors

Download ppt "Fig. 4 Scalable module illustration."

Similar presentations

Self-sensing of actuator position.

Self-sensing of actuator position.
The milliDelta: a millimeter-scale Delta robot.

The milliDelta: a millimeter-scale Delta robot.
Fig. 2 New bathymetry. New bathymetry. (A) Uninterpreted bathymetry. Black lines represent seismic profiles acquired. The white line shows the position.

Fig. 2 New bathymetry. New bathymetry. (A) Uninterpreted bathymetry. Black lines represent seismic profiles acquired. The white line shows the position.
Fig. 4 Estimations of nonlinear functionals of a single-qubit state with the quantum Fredkin gate. Estimations of nonlinear functionals of a single-qubit.

Fig. 4 Estimations of nonlinear functionals of a single-qubit state with the quantum Fredkin gate. Estimations of nonlinear functionals of a single-qubit.
Fig. 4 3D reconfiguration of liquid metals for electronics.

Fig. 4 3D reconfiguration of liquid metals for electronics.
Fig. 3 Theoretical analysis of the thermalization pathways.

Fig. 3 Theoretical analysis of the thermalization pathways.
Fig. 3 The electrical contact of direct-printed and reconfigured liquid metals. The electrical contact of direct-printed and reconfigured liquid metals.

Fig. 3 The electrical contact of direct-printed and reconfigured liquid metals. The electrical contact of direct-printed and reconfigured liquid metals.
Fig. 1 Demographic shifts in knowledge producers.

Fig. 1 Demographic shifts in knowledge producers.
Fig. 4 Electrical properties and patterning of the stretchable PEDOT/STEC (STEC content is 45.5 wt % for all). Electrical properties and patterning of.

Fig. 4 Electrical properties and patterning of the stretchable PEDOT/STEC (STEC content is 45.5 wt % for all). Electrical properties and patterning of.
Self-sensing of actuator position.

Self-sensing of actuator position.
Fig. 3 Bioresorbable interfaces to the optical sensors.

Fig. 3 Bioresorbable interfaces to the optical sensors.
Fig. 3 Faculty placement distributions.

Fig. 3 Faculty placement distributions.
Fig. 3 Piezoresistive e-skin with interlocked microdome arrays for simultaneous detection of static pressure and temperature. Piezoresistive e-skin with.

Fig. 3 Piezoresistive e-skin with interlocked microdome arrays for simultaneous detection of static pressure and temperature. Piezoresistive e-skin with.
Fig. 2 Fluence-dependent emission characteristics of CH3NH3PbI3 recorded at 15 and 300 K. Fluence-dependent emission characteristics of CH3NH3PbI3 recorded.

Fig. 2 Fluence-dependent emission characteristics of CH3NH3PbI3 recorded at 15 and 300 K. Fluence-dependent emission characteristics of CH3NH3PbI3 recorded.
Fig. 1 Experimental schematic and setup.

Fig. 1 Experimental schematic and setup.
Fig. 1 TED design and fabrication process.

Fig. 1 TED design and fabrication process.
Fig. 2 Materials and designs for bioresorbable PC microcavity-based pressure and temperature sensors. Materials and designs for bioresorbable PC microcavity-based.

Fig. 2 Materials and designs for bioresorbable PC microcavity-based pressure and temperature sensors. Materials and designs for bioresorbable PC microcavity-based.
Fig. 5 The gate voltage dependence of IEE of the Rashba-split 2DEG between SrTiO3 and 3-UC LaAlO3. The gate voltage dependence of IEE of the Rashba-split.

Fig. 5 The gate voltage dependence of IEE of the Rashba-split 2DEG between SrTiO3 and 3-UC LaAlO3. The gate voltage dependence of IEE of the Rashba-split.
Bioinspiration and working principle of FEDEA.

Bioinspiration and working principle of FEDEA.
Fig. 4 Electrical properties of GAP multilayer conductors and small-angle x-ray scattering analysis for the percolation network of Au NPs in a PU matrix.

Fig. 4 Electrical properties of GAP multilayer conductors and small-angle x-ray scattering analysis for the percolation network of Au NPs in a PU matrix.

Similar presentations

Ads by Google