Presentation is loading. Please wait.

Presentation is loading. Please wait.

Fig. 3 3D printing accuracy, swelling, and mechanical properties after cross-linking and bacterial growth using a 4.5 wt % Flink and Flink-GMHA. 3D printing.

Published bySydney Mathews Modified over 5 years ago

Similar presentations

Presentation on theme: "Fig. 3 3D printing accuracy, swelling, and mechanical properties after cross-linking and bacterial growth using a 4.5 wt % Flink and Flink-GMHA. 3D printing."— Presentation transcript:

1 Fig. 3 3D printing accuracy, swelling, and mechanical properties after cross-linking and bacterial growth using a 4.5 wt % Flink and Flink-GMHA. 3D printing accuracy, swelling, and mechanical properties after cross-linking and bacterial growth using a 4.5 wt % Flink and Flink-GMHA. (A to C) Various shapes of Flink hydrogels containing localized bacteria with high precision in 3D. (D) Multimaterial 3D printing with spatial segregation of two bacterial strains. P. putida is labeled with DAPI (blue) and localized in the horizontal lines, whereas B. subtilis is colored with Nile Red (green) and embedded in the vertical lines. (E) Flink (6 wt %; without bacteria) was modified with GMHA to form a UV–cross-linked water-insoluble hydrogel after UV light exposure (365 nm for 60 s at 90 mW). The hydrogels are shown after printing, after 1 hour in bacterial medium and after 1hour in DI water, respectively. (F) Amplitude oscillatory sweeps of the modified Flink-GMHA (4.5 wt %) before and after cross-linking. Strains in the range from 0.01 to 100% at an angular frequency of 1 rads−1 were applied in these measurements. All scaffolds are self-sustaining and resilient. Manuel Schaffner et al. Sci Adv 2017;3:eaao6804 Copyright © 2017 The Authors, some rights reserved; exclusive licensee American Association for the Advancement of Science. No claim to original U.S. Government Works. Distributed under a Creative Commons Attribution NonCommercial License 4.0 (CC BY-NC).

Download ppt "Fig. 3 3D printing accuracy, swelling, and mechanical properties after cross-linking and bacterial growth using a 4.5 wt % Flink and Flink-GMHA. 3D printing."

Similar presentations

Fig. 2 Transport properties of a BP transistor at low temperature.

Fig. 2 Transport properties of a BP transistor at low temperature.
Fig. 2 Global production, use, and fate of polymer resins, synthetic fibers, and additives (1950 to 2015; in million metric tons). Global production, use,

Fig. 2 Global production, use, and fate of polymer resins, synthetic fibers, and additives (1950 to 2015; in million metric tons). Global production, use,
Fig. 2 CFD results. CFD results. Results of CFD simulations in horizontal (left column) and vertical (right column) cross-sections. All models oriented.

Fig. 2 CFD results. CFD results. Results of CFD simulations in horizontal (left column) and vertical (right column) cross-sections. All models oriented.
Fig. 5 Thermal conductivity of n-type ZrCoBi-based half-Heuslers.

Fig. 5 Thermal conductivity of n-type ZrCoBi-based half-Heuslers.
Fig. 1 Map of water stress and shale plays.

Fig. 1 Map of water stress and shale plays.
Fig. 1 Examples of experimental stimuli and behavioral performance.

Fig. 1 Examples of experimental stimuli and behavioral performance.
Fig. 3 Electron PSD in various regions.

Fig. 3 Electron PSD in various regions.
Fig. 4 Morphogenesis in the Ch-CNC host droplets and NP assemblies.

Fig. 4 Morphogenesis in the Ch-CNC host droplets and NP assemblies.
Fig. 2 Some examples of weekly forecasts (the number of the forecasts are reported on Table 1). Some examples of weekly forecasts (the number of the forecasts.

Fig. 2 Some examples of weekly forecasts (the number of the forecasts are reported on Table 1). Some examples of weekly forecasts (the number of the forecasts.
Fig. 4 Resynthesized complex boronic acid derivatives based on different scaffolds on a millimole scale and corresponding yields. Resynthesized complex.

Fig. 4 Resynthesized complex boronic acid derivatives based on different scaffolds on a millimole scale and corresponding yields. Resynthesized complex.
HT synthesis of boronic acids using the building block approach

HT synthesis of boronic acids using the building block approach
Fig. 6 Comparison of properties of water models.

Fig. 6 Comparison of properties of water models.
Fig. 1 Mean and median RCR (Relative Citation Ratio) of Roadmap Epigenomics Program research articles for each year. Mean and median RCR (Relative Citation.

Fig. 1 Mean and median RCR (Relative Citation Ratio) of Roadmap Epigenomics Program research articles for each year. Mean and median RCR (Relative Citation.
Fig. 2 Reference-fixing experiment, results.

Fig. 2 Reference-fixing experiment, results.
Fig. 3 Swarm material properties.

Fig. 3 Swarm material properties.
Fig. 2 TRXSS data. TRXSS data. TRXSS data covering delay times from 10 ns to 10 ms for wild-type DmCry (A), for the DmCry(H378A) mutant (B), and for XlPho.

Fig. 2 TRXSS data. TRXSS data. TRXSS data covering delay times from 10 ns to 10 ms for wild-type DmCry (A), for the DmCry(H378A) mutant (B), and for XlPho.
Fig. 3 Rotation experiment, setup.

Fig. 3 Rotation experiment, setup.
Fig. 1 Product lifetime distributions for the eight industrial use sectors plotted as log-normal probability distribution functions (PDF). Product lifetime.

Fig. 1 Product lifetime distributions for the eight industrial use sectors plotted as log-normal probability distribution functions (PDF). Product lifetime.
Fig. 5 Structural photocycle for DmCry.

Fig. 5 Structural photocycle for DmCry.
Fig. 1 Touchless manipulation of objects based on the interaction with magnetic fields. Touchless manipulation of objects based on the interaction with.

Fig. 1 Touchless manipulation of objects based on the interaction with magnetic fields. Touchless manipulation of objects based on the interaction with.

Similar presentations

Ads by Google