Presentation is loading. Please wait.

Presentation is loading. Please wait.

Tutorial 1 Learning Topology Optimization Through Examples and Case Studies August 18, 2019.

Published byMiroslava Šimková Modified over 5 years ago

Similar presentations

Presentation on theme: "Tutorial 1 Learning Topology Optimization Through Examples and Case Studies August 18, 2019."— Presentation transcript:

1 Tutorial 1 Learning Topology Optimization Through Examples and Case Studies
August 18, 2019

2 Use Pareto Method for Topology Optimization
Problem Description Cantilever Beam Problem Units: MKS Material: AlloySteel Structural Loads: 1000N Mesh Size: use default mesh size TopOpt Constraints: No Constraints Goal: Optimize the topology for a volume fraction of 0.25 1000N Use Pareto Method for Topology Optimization

3 Pareto Method based TO Choose Units Load Geometry Define Material
Apply Loads (Structural/Thermal/Gravity) Carry out FEA Apply Top Opt Constraints Topology Optimization PostProcessing

4 Results

Download ppt "Tutorial 1 Learning Topology Optimization Through Examples and Case Studies August 18, 2019."

Similar presentations

Pre-stresses Influence on a Micro Mirror Structure.

Pre-stresses Influence on a Micro Mirror Structure.
Prestressed Modal Analysis Workshop 5.2. Workshop Supplement Prestressed Modal Analysis August 26, 2005 Inventory #002266 WS5.2-2 Workshop 5.2 - Goals.

Prestressed Modal Analysis Workshop 5.2. Workshop Supplement Prestressed Modal Analysis August 26, 2005 Inventory # WS5.2-2 Workshop Goals.
Symmetry & boundary conditions Joël Cugnoni, LMAF/EPFL, 2009.

Symmetry & boundary conditions Joël Cugnoni, LMAF/EPFL, 2009.
Project 2: Torque-Arm Modeling, Simulation and Optimization

Project 2: Torque-Arm Modeling, Simulation and Optimization
Mesh, Loads & Boundary conditions CAD Course © Dr Moudar Zgoul, 2010-2011.

Mesh, Loads & Boundary conditions CAD Course © Dr Moudar Zgoul,
A “CANTILEVER” EXPERIENCE OF LARGE PROPORTIONS Pinocchio's Nose.

A “CANTILEVER” EXPERIENCE OF LARGE PROPORTIONS Pinocchio's Nose.
Procedures of Finite Element Analysis Two-Dimensional Elasticity Problems Professor M. H. Sadd.

Procedures of Finite Element Analysis Two-Dimensional Elasticity Problems Professor M. H. Sadd.
Abstract/Objectives Better understand the effects of typical GD&T variations on Bolt Stresses in Torque Carrying Bolted Flanges Create Trend Curves for.

Abstract/Objectives Better understand the effects of typical GD&T variations on Bolt Stresses in Torque Carrying Bolted Flanges Create Trend Curves for.
Optimization of a FEA Beam Element Model for Computational Speed and Accuracy Brent Weight and Ryan Weight.

Optimization of a FEA Beam Element Model for Computational Speed and Accuracy Brent Weight and Ryan Weight.
2D Analyses Mesh Refinement Structural Mechanics Displacement-based Formulations.

2D Analyses Mesh Refinement Structural Mechanics Displacement-based Formulations.
Optimization of a Flapping Wing Irina Patrikeeva HARP REU Program Mentor: Dr. Kobayashi August 3, 2011.

Optimization of a Flapping Wing Irina Patrikeeva HARP REU Program Mentor: Dr. Kobayashi August 3, 2011.
The problem to be solved is specified in a) the physical domain and b) the discretized domain used by FEA Governing principle law :

The problem to be solved is specified in a) the physical domain and b) the discretized domain used by FEA Governing principle law :
June 29, 2007 1 The difference between two feature models Matthijs Sypkens Smit Willem F. Bronsvoort CAD ’07 Conference, Honolulu, Hawaii Faculty of Electrical.

June 29, The difference between two feature models Matthijs Sypkens Smit Willem F. Bronsvoort CAD ’07 Conference, Honolulu, Hawaii Faculty of Electrical.
Introduction to ABAQUS 27 th February, 2007. Units Before starting to define any model, you need to decide which system of units you will use. ABAQUS.

Introduction to ABAQUS 27 th February, Units Before starting to define any model, you need to decide which system of units you will use. ABAQUS.
Structures and stress BaDI 1.

Structures and stress BaDI 1.
Flexible Self Locking Pin-less Joint

Flexible Self Locking Pin-less Joint
A Designer’s Approach for Optimizing an End-Loaded Cantilever Beam while Achieving Structural and Manufacturing Requirements Timothy M. Demers November.

A Designer’s Approach for Optimizing an End-Loaded Cantilever Beam while Achieving Structural and Manufacturing Requirements Timothy M. Demers November.
RPI Master’s Project Proposal Stephen Ganz – 5/15/2012 Structural Analysis of Bridge Gusset Plates: Steel vs. Composite.

RPI Master’s Project Proposal Stephen Ganz – 5/15/2012 Structural Analysis of Bridge Gusset Plates: Steel vs. Composite.
Axisymmetric Analysis of a Pipe Assembly

Axisymmetric Analysis of a Pipe Assembly
Project Proposal 2 Tangent Tube Slip Spacer. GOALS Determine the maximum load which the Tangent Tube Slip Spacer(TTSS) Can Support Suggest improvements.

Project Proposal 2 Tangent Tube Slip Spacer. GOALS Determine the maximum load which the Tangent Tube Slip Spacer(TTSS) Can Support Suggest improvements.

Similar presentations

Ads by Google