1. Instructional Presentation
DEMA TITAN WAREWASH
T-812 &T-813
Instructional Presentation

2. The Titan responds to detergent and rinse triggers in the range of
The Titan ware wash system controls all chemical delivery functions for dish machines and similar warewash applications. The system has an advanced power supply that will accept 100V–250V 50/60Hz.
The Titan responds to detergent and rinse triggers in the range of
20V–500V 50/60Hz. The Titan has been designed for simple
installation, set up, and operation.
The Titan has an Auto Switchover feature that allows automatic switching
from Concentration to Probeless in the case of a probe fault,
(and back again if the fault clears). This feature allows continued operation
or the dish machine while cutting down on unnecessary service calls.
Conditions that can activate this feature are the following:
Open probe – a probe wire is disconnected or there is lime buildup on the tips.
Closed probe – a piece of flatware may be lying across the probe tips.
Detergent not feeding properly – too much or too little detergent.

3. Chapter Selection Click on the chapter you wish to view
1. Installation
2. Initial Programming
3. System Access
4. Diagnostic Mode
5. Accessories
6. Parts Breakdown
Click on the chapter you wish to view

4. Installation Wall Mounting Electrical Connection Tubing
Conductive Probe

5. Wall Mounting Unpack the Titan
Remove mounting plate from Titan (Remove screw and slide plate down)
Attach mounting plate to wall
Replace Titan on the mounting plate (Replace screw)

6. Unpack Titan

7. Remove screw and slide Mounting Plate off (downward direction)
Removing Mounting Plate
Remove screw and slide Mounting Plate off (downward direction)

8. Prior to mounting Titan Location should be based on:
Desired location of Titan and chemicals
Electrical Connection for Titan
Flat vertical surface away from splashing and steam originating from machine
Titan should must be placed so that it can be easily observed and serviced

9. Attach to Surface

10. Follow instructions on Mounting Bracket
Replace Titan on
Mounting Plate
Follow instructions on Mounting Bracket

11. Electrical Connection
Connect power to the Titan per dish machines manufacture's recommendations. Constant power should be supplied to the Titan anytime the dish machine power is on. The Titan can also be plugged directly into a wall socket.
Connect the Detergent Trigger to the machine.( If the Machine does not have a specific trigger connection, then the trigger should be wired to the coil of the Motor Contactor)
Connect the Rinse Trigger to the Machine. (If the Machine does not have a specific rinse trigger connection, then the trigger should be wired to the Rinse Solenoid Valve)

12. Tubing Connections Tubing connection from the Titan to the Machine.
Tubing connection from the Titan to the Chemical.

13. Attaching the Bulkhead Fitting for the chemical injection of a liquid detergent.
Inside
Outside
Chemical injection fitting must be above the water level in the tank
Chemical Injection fitting should be directly above Conductive Probe

14. Installing Conductive Probe
Inside
Outside
The Probe should be installed 2/3 down from water level of the tank
The probe should be installed directly below chemical injection

15. Click here to return to Main Menu
Press Enter to continue to Initial Programming

16. Enduser accessable menu
Initial Programming
Enduser accessable menu

17. Changing Languages Press to get to language screen
Press to start edit screen
Press or to change languages
Press to accept change

18. Pump will run for 2 minutes if it is not stopped manually
Detergent Prime
Press to scroll to Detergent Prime
Press to start priming
Press again to stop priming
Pump will run for 2 minutes if it is not stopped manually

19. Pump will run for 2 minutes if it is not stopped manually
Rinse Prime
Press to scroll to Rinse Prime
Press to start priming
Press again to stop priming
Pump will run for 2 minutes if it is not stopped manually

20. Pump will run for 2 minutes if it is not stopped manually
Sanitizer Prime
Press to scroll to Sanitizer Prime
Press to start priming
Press again to stop priming
Pump will run for 2 minutes if it is not stopped manually

21. Detergent Status Display
Press to display Status
C - Concentration I – Initial Set Point in Concentration Mode Detergent Sensor
P – Probeless D – Dwell Alarm Point in Probeless mode Probe Reading
T – Recharge
+ Titan is feeding detergent
- Titan is not feeding detergent
* Screen will stay active for 30 minutes until the up or down arrow is pressed or 30 minutes lapse

22. Rack Count
Rack Count 00000
This is a read only record

23. Descale
Press to start
Press again to stop

24. Click here to return to Main Menu
Press Enter to continue to System Access

25. System Access
System Access is only available after Initial Programming is completed

26. Enter Code

27. Dispenser SetupParameters

28. Control Mode

32. Use to enter letters

33. Use to adjust volume

43. Click here to return to Main Menu
Press Enter to continue to Diagnostic Mode

44. Diagnostic Mode

45. Sanitizer
Level
Detergent
Level
Rinse
Level

46. C - Concentration I – Initial Set Point in Concentration Mode Detergent Sensor
P – Probeless D – Dwell Alarm Point in Probeless mode Probe Reading
T – Recharge
+ Concentration mode
- not Concentration mode
* - When a trigger is present

47. Rinse Status Screen L – Liquid D - Dry D – Delay R – Rinsing L – Limit
Reached
Rinse Alarm
Set Point
Rinse Sensor
Reading

48. Sanitizer Status Screen
Sensor
Reading
Liquid
+ - running
- - not running
Sanitizer alarm set Point

49. Displays total switchover count for OVER and Under feeding
Displays total switchover counts for
An open probe or shorted probe

50. Now the Titan is Setup and ready for use.
Click here to return to Main Menu
Press enter to veiw Accessories

51. Accessories Magnetic Field Reader Inductive Warewash Probe
(Click on one of the following)
Magnetic Field Reader
The DEMA Magnetic Field Reader eliminates the need to make wire connections to warewash and laundry machines. The DEMA Magnetic Reader detects the presence of the magnetic field surrounding an AC solenoid valve or Ac motor. This may then be used as a trigger signal to a DEMA warewash or laundry dispenser.
Inductive Warewash Probe
The DEMA Inductive Warewash Probe replaces the conductivity probe used to sense detergent concentration in the wash tank. The advanced technology of the DEMA Inductive Warewash Probe allows the wash tank conductivity to be sensed without any metal contacting the wash tank solution. As a result, the DEMA Inductive Warewash Probe is immune to contaminants, such as lime, which plate onto conductivity probes.

52. DEMA Magnetic Field Reader
Disconnect the power from the Titan and the warewash machine.
Disconnect rinse or wash trigger cable ( ) from the Titan control board ( ).
Route the Magnetic Field Reader cable as shown on next page in to the Titan enclosure.
Plug the Magnetic Field Reader cable into rinse or wash trigger connector on the Titan control board ( ).
With the door on the Titan fully open; secure the Magnetic Field Reader cable in the bottom plate of the Titan with strain relief ( ).
Close the door on the Titan.
Place the Magnetic Field Reader against the coil of the solenoid valve or motor housing to be used for sensing. The sensing element is on the bottom side of the Magnetic Field Reader below the point of the arrow that is on the top.
Secure the Magnetic Field Reader in place with the Hook & Loop strap. The strap may be trimmed as required.
Turn the power on the Titan.
Turn on the power to the warewash machine.
Energize the solenoid valve or motor to which the Magnetic Field Reader is attached.
After one second a green LED on the Magnetic Field Reader should illuminate next to the cable. If it does not illuminate, reposition the sensor until it does.

53. DEMA Magnetic Field Reader
De-energize the solenoid valve or motor. The green LED should turn off after one second. If it stays on, reposition the sensor.
When properly installed the green LED will turn on one second after the solenoid valve or motor which it is attached is activated. It will turn off one second after deactivation.

54. Inductive Warewash Probe
Disconnect the power from the Titan and the warewash machine.
Drain the warewash machine
Disconnect the probe wire from the Titan control board and remove the conductivity probe from the tank.
Install the DEMA Inductive Warewash Probe in the wash tank, through the wall shown on next page. The hole through the center of the DEMA Inductive Warewash Probe must be vertical.
Route the DEMA Inductive Warewash Probe cable, as shown on the next page, into the Titan enclosure. The connector and strain relief fit the ¾” hole in the bottom-center access panel of the Titan enclosure.
Plug the DEMA Inductive Warewash Probe cable into the white eight pin connector on the Titan control board ( ). The connector is directly above the microcontroller chip.
With the door on the Titan fully open; secure the DEMA Inductive Warewash Probe cable in the bottom plate of the Titan with strain relief ( or-3).
Close the door on the Titan.
Turn on the power to the Titan
Turn on the power to the warewash machine.

55. Inductive Warewash Probe
NO.
PART NUMBER
DESCRIPTION 1
(Use either -2 or -3)
Cable Strain Relief 5/8”
Cable Strain Relief 3/4" 2
Inductive Probe Kit

56. TITAN INSTALATION KITS
TITAN ELECTRONIC KITS
TITAN INSTALATION KITS

57. TITAN TECHNICAL SPECIFICATION

62. TITAN PARTS BREAKDOWN