Download presentation
1
ELECTROLUX REFRIGERATOR
Control Board TURN TO PAGE 183 IN YOUR TRAINING MANUAL
2
2500 ++ User Interface Board Main Board
Located in the door Main Board Located under the refrigerator
3
ACTIVATION OF SERVICE MODE
Press and hold the FREEZER TEMPERATURE UP (+) key and FREEZER TEMPERATURE DOWN ( -) for 5 seconds. Each press of the FRESH FOOD TEMPERATURE UP (+) will step through the variables of each test and display the test information in the Fresh Food Display.
4
Service Mode REMEMBER: This is a service mode, not a diagnostic mode. The service mode will allow you to test components but will not show specific error codes although the does have the capability to show an error during some tests.
5
Service Mode On activation of the service mode, all LED lights on the display will illuminate. - Pressing the Fresh Food (+) key will blank the display - Pressing the FF (+) key again will begin the first test. To actuate a load on a particular component (turn it on or off), use the ON/OFF key present on the user interface. To step to the next test – use the FF (+) key.
6
Once you pass a number, you can not go back
Service Mode Once you pass a number, you can not go back
7
AC Load Testing 2500++ Service Mode “2” = Defrost Heater
“3” = Fresh Food Lights “8” = Water Valve “9” = Freezer Lights “10” = Auger Motor “11” = Cubed / Crush Solenoid “12” = Condenser Fan
8
DC Load Testing 2500++ Service Mode “38” = Vcc Compressor
“15” = Evaporator Fan “22” = Damper
9
Digital Input Test 2500++ Service Mode “23” = FF Door Switch
“24” = FZ Door Switch “26” = DTT - Defrost Limit Switch “27” = FF Ice Maker “28” = Paddle “29” = FF Thermistor (Er in FZ if bad) “30” = FZ Thermistor (Er in Fz if bad) “33” = Ambient Thermistor (Er in FZ if bad)
10
Service Mode Flapper Test “36” = Fire Solenoid with On/Off
11
DEACTIVATION OF SERVICE MODE
Press and hold the FF(+) for 5 seconds Mode will automatically deactivate after 5 minutes of no key entry
12
MANUAL DEFROST MODE 2500++ Service Mode
Activation: Press and hold FF temperature (+) key while pressing the FF temperature (-) within 6 seconds. FREEZER SHOULD DISPLAY “d” FRESH FOOD DISPLAY “F”
13
MANUAL DEFROST MODE 2500++ Service Mode
If the manual defrost is activated during a normal automatic defrost cycle, then: FREEZER DISPLAY “AD” FRESH FOOD DISPLAY “F” After completion of the automatic defrost cycle, the power board will send the heater ON time. U/I should display this on time for 10 seconds.
14
MANUAL DEFROST MODE 2500++ Service Mode
DeActivation: Press and hold FF temperature (+) key while pressing the FF temperature (-) within 6 seconds or do a power-on-reset. FREEZER SHOULD DISPLAY “d” FRESH FOOD DISPLAY “F”
15
DEFROST FAILURE 2500++ Service Mode
FREEZER DISPLAY will flash 1hz FRESH FOOD DISPLAY will flash 1 hz
16
2500++ Service Mode Communication in between 2500++ and UI board
If the communication is lost between the Main control board and the User Interface, the following will occur: The user interface will show “CE” in both the FF and FZ displays The user interface will disable all functions including alarms
17
ALERTS FF actual temperature greater than 55 degrees and above 55F degrees for 20 minutes - display “HI” in FF display. FZ actual temperature greater than 26 degrees and above 26F degrees for 20 minutes - display “HI” in FZ display
18
ALERTS During and 1 hour after defrost: high temperature alarm is disabled. Show Room Mode will display 70 in both displays System OFF: display “OFF” in both FF and FZ displays Sabbath Mode: Display “5b” in both FF and FZ displays Evaporator Fan failure: Display “E” in FZ display and display “f” in FF display Door Ajar: if system is ON and door remains open for more than 5 minutes
19
Service Mode Questions ?
Similar presentations
© 2024 SlidePlayer.com. Inc.
All rights reserved.