1. Telemetry Modules Quick Start
Inventia sp. z o.o. All rights reserved

2. Necessary Software Microsoft Framework 1.1 MTManager
MT-Data Provider v2.4
Mod-Dog
Softing OPC or other OPC client
All programs should be installed with default settings
Inventia sp. z o.o. All rights reserved

3. Configuring MT-301 with MTM2.
2. Enter project name
1. Run MTM
3. Add new module right-clicking on project name
Inventia sp. z o.o. All rights reserved

4. Configuring MT-301 with MTM
4. Enter module name and
chose type and firmware
Tip:
If you don’t know which firmware version do you have, choose the default one. During reading or writing configuration MTM will point you the right one. Then use Change version option from right click menu to correct settings.
Inventia sp. z o.o. All rights reserved

5. Configuring MT-301 with MTM
5. Choose General from Device list
In SIM card PIN number field enter PIN card number that you plan to use.
Make sure that Use of GPRS option is set to “Yes”
Inventia sp. z o.o. All rights reserved

6. Configuring MT-301 with MTM
6. Click GPRS in Device list. Enter your APN name, APN user name
and APN login password if required.
Inventia sp. z o.o. All rights reserved

7. Configuring MT-301 with MTM
7. Expand Authorized numbers in Device list and choose IP subcategory.
Enter IP Number of SIM card that will be used in module connected to
the PC.
Inventia sp. z o.o. All rights reserved

8. Configuring MT-301 with MTM
Click Resources in Device list and check Internal resources
Modbus ID number. Here you can be set ID number allowing access to the module internal resources from Modbus net.
Inventia sp. z o.o. All rights reserved

9. Configuring MT-301 with MTM
9. Connect MT-301 to PC using RS cable
10. Click Environment button
11. Choose your COM port number and apply by clicking Write
Inventia sp. z o.o. All rights reserved

10. Configuring MT-301 with MTM
12. Make sure your SIM card is installed.
Then click Write and watch the progress bar.
11. Click Connect to establish connection
13. Accept by clicking OK
Inventia sp. z o.o. All rights reserved

11. Configuring MT-301 with MTM
14. After a while module sholud log on to the APN.
Such state is sygnalized by LEDs on module
cover. They should blink like below.
Inventia sp. z o.o. All rights reserved

12. Configuring MT-202 with MTM
16. Enter PIN and set Modem
operating mode in General
15. Add new module MT-202
17. Choose Transmision speed in Resources/Serial port,
connect MT-202 and Write the configuration
Inventia sp. z o.o. All rights reserved

13. Add hardware in Windows Control Panel
18.
In Control Panel click Add Hardware
19. Add new modem to
the operating system
Inventia sp. z o.o. All rights reserved

14. Dial-up configuration
20. In Control Panel click „Network Connection”
21. Create a new connection
Enter name of connection
Enter acces number
Enter user name and password if needed
Inventia sp. z o.o. All rights reserved

15. Dial-up configuration
22.
Connect MT-202 with PC using port 2
Tips: If the dial-up connection
have failed, you can force
handshake on the COM port
from PC side:
23.
Click on APN icon
24.
Click Properties
Inventia sp. z o.o. All rights reserved

16. Dial-up configuration
25.
In the bookmark Options change
„Redialing options”
26.
In the bookmark Networking
Chose TCP/IP protocol and
Click Properties button
27.
Click „Advanced” button
28.
Uncheck „use default gateway…”
checkbox
After that click 3 times „OK” and DIAL then you will see:
Inventia sp. z o.o. All rights reserved

17. MT- Data Provider – first steps
33.
In that area you configure what data you can read from or write to
remote module. Default ID modbus is „1” just like in MTM.
32.
Here you should to put correct type of the module
31.
Next move is entering IP number of SIM card that is mounted in the MT-202 module.
30.
First step is to change default sample.xml file. You must enter IP numbers of remote module (MT-301)
29.
After installation go to destination directory: ”C:\Program Files\InVentia\MTopc2\” and open „sample.xml” in NOTEPAD
Tip:
You can find more
info about XML
parameters in
readme.pdf located
in MT Data Provider
folder.
34. Now you can save and close sample.xml
Inventia sp. z o.o. All rights reserved

18. MT- Data Provider – first steps
35.
From Start/All programs/Softing OPC toolbox… run Softing OPC.
36.
Click on the DA items bookmarks
33.
Left click od DA Browse bookmark and right click on server ID
And left click on „Add Item for all tags”
32.
Double Click on MT-OPC server will start driver
Inventia sp. z o.o. All rights reserved

19. MT- Data Provider – first steps
37.
Here you will see quality good for all configured tags in sample.xml
For example „device—slave.BO0” is the binary output Q1
Enter ‘1’ in this field and click write to send ‘1’ to the remote module
Inventia sp. z o.o. All rights reserved

20. Congratulations!!!
You have configured your first telemetry system based on module MT-301 produced by InVentia !!!
Inventia sp. z o.o. All rights reserved
Inventia sp. z o.o. All rights reserved