1. Working principles of pumps

2. History of Reciprocating pumps
In 17th century Egyptians in Alexandria built reciprocating fire pump and and it had all the parts of today’s pump.
About Newcomen (Great Britain) built a reciprocating pump using steam engine as the driver.
He was the first man to use seam for driving purposes.
In Worthington (U.S.A) developed a steam engine driven pump.
Then many developments came.

3. History of Centrifugal pumps pumps
The inventor ca not be name with assurance.
In the 17th century Jordan, an Italian had made some drawing of a centrifugal pumps.
In the early 18 century French physicist Papin built a centrifugal pump of primitive design.
In 1732 Demouir pumps was put on service in France,
In 1818 Andrews ( USA) built a single stage centrifugal pump.
Then many developments came in the industry...

4. History of best pump
Human heart.
Everybody knows Who invented.

5. Pumps are used to move liquids
200
meters
100
Bar M
10 kms
Pumps are used to move liquids
from a lower pressure system to higher pressure
From a lower elevation to higher elevation
From one place to another place at different/same elevation and pressure.

6. Energy needed for pumps= volumetric flow*pressure
200
meters
100
Bar 10
kms M
Pumps add pressure energy to over come
elevation needs ( potential energy)
Frictional losses
Delta pressure requirements
Energy needed for pumps= volumetric flow*pressure

7. Power required for pumping
Power = mass X dynamic head
Power ( kW)= H Q r/367000
H = Total head in meters Q=Flow M3/H
r=Density in Kg/M3
Power required for pumping
Power ( kW)= H Q r/35.99
H = Total head in barA Q= Flow M3/H
r=Density in Kg/M3
Pleased divide by efficiency for actual power
Please refer Perry

8. How to give energy ?
Centrifugal force
(throwing)
Positive displacement
(physically pushing)

9. Centrifugal pumps

10. Working principles centrifugal pumps

11. Parts of a centrifugal pump
Impeller
Casing
Eye
Seal/packing
Wear ring
Parts of a centrifugal pump

12. Advantages of centrifugal pumps
It simple and easy to construct. Available in different materials .
Absence of valves. Less maintenance.
High rpm design. Can be coupled to a motor directly.
Steady delivery.
No damage in delivery is blocked.
Smaller in Size when compared to reciprocating type for the same capacity.
Can handle slurries.
Advantages of centrifugal pumps

13. Dis-Advantages of centrifugal pumps
For high pressure we need multistage pump which are complex to construct.
Efficiency is high only over a range.( explain graph)
Usually not self priming
Non return valve is needed in the delivery to avoid back flow.
Very viscous fluid can not be handled/
Dis-Advantages of centrifugal pumps

14. Types centrifugal pumps
Typical classification
Single stage
Multistage
Explain why and how

15. Single stage

16. Multi stage
Multistage pumps are used to limit rpm and whenever we have high DP. Example BFW pumps.

17. Thrust balance centrifugal pumps
1. Double suction pumps
2. Thrust balance in multistage pumps
Stage arrangement
3. Thrust balance line and thrust disk and bearing

18. Double suction pumps
Sea water

19. Double suction pumps 323-J UREA

20. Thrust balance in a multi-stage pump
Multistage pumps
Thrust balance in a multi-stage pump

21. Multistage BFW Pump Ammonia

22. Thrust balance in a multi-stage pump
Multistage pumps
Out In
Thrust balance in a multi-stage pump
Explain the principle of balance disc
Thrust balance line and caution

23. Explain thrust balance
Multistage pump
Explain thrust balance

24. Positive displacement pumps

25. Positive displacement pumps
Reciprocating
Rotary

26. Reciprocating Pumps Piston type Vertical& Horizontal & double acting
Plunger type
Diaphragm pump

27. Explain double acting, plunger type , vertical, horizontal, multistage
Reciprocating pumps
Explain double acting, plunger type , vertical, horizontal, multistage

28. Diaphragm pumps

29. Diaphragm pumps

30. Diaphragm Reciprocating pumps
Basic principle is similar to a reciprocating plunger pump/
Plunger pressurizes the hydraulic oil which when pressurized pushes the diaphragm and discharge starts.
Stroke length can be adjusted and hence the dosing flow rate.
No direct contact of plunger with the solution.
Direct contact is only with diaphragm ( neoprene, Teflon etc)

31. Diaphragm Reciprocating pumps
Figure 1: The air valve directs pressurized air to the back side of diaphragm "A". The compressed air is applied directly to the liquid column separated by elastomeric diaphragms.
The compressed air moves the diaphragm away from the center block of the pump. The opposite diaphragm is pulled in by the shaft connected to the pressurized diaphragm. Diaphragm "B" is now on its air exhaust stroke; air behind the diaphragm has been forced out to atmosphere through the exhaust port of the pump. The movement of diaphragm "B" toward the center block of the pump creates a vacuum within the chamber "B". Atmospheric pressure forces fluid into the inlet manifold forcing the inlet ball off its seat. Liquid is free to move past the inlet valve ball and fill the liquid chamber.
Diaphragm Reciprocating pumps

32. Diaphragm Reciprocating pumps
Figure 2: When the pressurized diaphragm, diaphragm"A", reaches the limit of its discharge stroke, the air valve redirects pressurized air to the back side of diaphragm "B". The pressurized air forces diaphragm "B" away from the center block while pulling diaphragm "A" to the center block. Diaphragm "B" forces the inlet valve ball onto its seat due to the hydraulic forces developed. These same hydraulic forces lift the discharge valve ball, forcing fluid flow to flow through the pump discharge. The movement of diaphragm "A" to the center block of the pump creates a vacuum within liquid chamber "A". Atmospheric pressure forces fluid into the inlet manifold of the pump. The inlet valve ball is forced off its seat allowing the fluid being transferred to fill the liquid chamber.
Diaphragm Reciprocating pumps

33. Diaphragm Reciprocating pumps
Figure 3: Upon completion of the stroke, the air valve again redirects air to the back side of diaphragm "A", and starts diaphragm "B" on its air exhaust stroke. As the pump reaches its original starting point, each diaphragm has gone through one air exhaust or one fluid discharge stroke. This constitutes one complete pumping cycle. The pump may take several cycles to become completely primed depending on the conditions of the application.

34. Gear and screw pumps High pressure and viscous fluids
Used in Samd for lube and seal oil pumps air booster of ammonia, 102-J

35. Gear pumps High pressure and viscous fluids
Example : lube/ seal oil pumps

36. See the solution is pushed out of the pump physically

37. Only one gear is used ( Explain)

38. Screw pumps High pressure and viscous fluids
Example : lube/ seal oil pumps

39. Talk about selection, parallel operation, reverse running etc.
SCREW PUMP
Talk about selection, parallel operation, reverse running etc.

40. SCREW PUMP

41. Talk about selection, parallel operation, reverse running etc.
SCREW PUMP
Talk about selection, parallel operation, reverse running etc.

42. Talk about selection, parallel operation, reverse running etc.
SCREW PUMP
Talk about selection, parallel operation, reverse running etc.

43. Sealing in pumps

44. Sealing in pumps
Fixed sealing – Packing
Centrifugal and reciprocating
Rotating – Mechanical seal
Centrifugal, gear pumps etc

45. Gland Packing

46. Gland packing principles
Stuffing box
Impeller
Gland packing principles
Explain packing stuffing box , heat generation and
cooling techniques. , Lantern rings ,flushing ,Cost and choice etc.

47. Packing
Explain packing stuffing box , heat generation and
cooling techniques. , Lantern rings ,flushing ,Cost and choice etc.

48. Packing

49. Mechanical seal

50. Three sealing points of a mechanical seal ( 1,2, and 3)
Stuffing box 3 2
Impeller 1
Fixed
Rotating
Three sealing points of a mechanical seal ( 1,2, and 3)

51. Mechanical seals

52. Mechanical seals

53. Mechanical seals
Explain working , heat generation and
cooling techniques, flushing ,Cost and choice etc.

54. Mechanical seals
Seal types

55. Mechanical seals

56. Mechanical seals

57. Double seals – Hazardous liquids
Explain need, sealant glycol, flushing etc.

58. Special Magnetic seals for hazardous/ expensive / corrosive fluids

59. Self-priming as they are inside the liquid.
Submersible pumps
Self-priming as they are inside the liquid.
Lube oil consoles , sump tanks, hazardous solution pumping etc.

60. End of part 1