1. www.accesslaserco.com 5603 47 th Ave NE, Marysville, WA 98270, USA 360-651-6141 Robust Stabilized CO 2 Lasers with Line Tracker Access Laser Company where innovation never stops

2. www.accesslaserco.com 5603 47 th Ave NE, Marysville, WA 98270, USA 360-651-6141 Main Features Offered with stabilized or grating tuned lasers Robust stabilization allows field applications where ambient environment changes. Stabilization without the side-effect of chirping inherent with the traditional dithering scheme. Power, spectrum, longitudinal mode and transverse modes are all stabilized at the same time. Maintains the stability of laser at any power level that is independently adjusted. Optimized sampling scheme depends on specifics of the laser model. Contact factory for details.

3. www.accesslaserco.com 5603 47 th Ave NE, Marysville, WA 98270, USA 360-651-6141 The Idea: Closed loop feedback control LaserBeam sampler LT Controller 1.Laser output is sampled and turned into an electronic signal 2.Signal is compared by the controller to the set value 3.Controller makes a decision whether to change the laser resonator. 4.Command is sent to laser to change or maintain the laser resonator. 5.Different from the traditional dithering approach: Piezo only moves to correct the residual drift of the well-stabilized resonator. There is no artificial frequency and power fluctuation introduced by the dither.

4. www.accesslaserco.com 5603 47 th Ave NE, Marysville, WA 98270, USA 360-651-6141 Find the Right Working Point - Grating Tuned Lasers Piezo moves around the set point to stabilize length of resonator. The correct working point for grating tuned lasers is at about 10% below the peak value and more than 10% above the valley, to provide enough room for correction. ~10/% >10/%

5. www.accesslaserco.com 5603 47 th Ave NE, Marysville, WA 98270, USA 360-651-6141 Lasy-4S with Line Tracker, an example Input from LT controller RF power input 45 deg beam sampler assembly Signal output to LT Controller

6. www.accesslaserco.com 5603 47 th Ave NE, Marysville, WA 98270, USA 360-651-6141 Lasy-4S with Line Tracker, small angle sampling Input from LT controller RF power input Small angle Beam sampler assembly Signal output to LT Controller

7. www.accesslaserco.com 5603 47 th Ave NE, Marysville, WA 98270, USA 360-651-6141 The LT Controller Push buttons (black): Mode SEL: Switch to pen loop or close loop Profiling: scan for a profile of power pattern Scaling: Auto gain control Up: Open loop mode- manually increase driving voltage. Close loop mode-manually increase power. Down: Open loop mode-manually decrease driving voltage. Close loop mode- manually decrease power. LEDs Top red: Power indicator Closed Loop: Red-searching, Green-locked. Open Loop: Lights up in open loop mode Profiling: Blinks during profiling Signal LVL: fast blinks all the time. Green-power too low; Red- Power too high; Amber-Power OK

8. www.accesslaserco.com 5603 47 th Ave NE, Marysville, WA 98270, USA 360-651-6141 LT Controller connections RS-232 to computer DB- 9 male HV to piezo on laser Input from 12 V DC supply Input from Sampler BNC OEM interface/ test connections DB-9 male

9. www.accesslaserco.com 5603 47 th Ave NE, Marysville, WA 98270, USA 360-651-6141 Monitoring Status of Laser and LT Controller Pin-5 Pin-1 Pin-6 Pin-9 Pin-1: HV monitor (analog) Pin-2: Scale-Over (digital) Pin-3: Mode (digital) Pin-4: Tracking (digital) Pin-5: Ground Pin-6: Scale-Under (digital) Pin-7: Power (Analog) Pin-8: Searching (digital) Pin-9: reserved Note: All pins are output

10. www.accesslaserco.com 5603 47 th Ave NE, Marysville, WA 98270, USA 360-651-6141 Computer interface: Line Tracker Software Press this start arrow to activate the program Select the appropriate serial port before activating the program It is a good idea to keep the power level at 700 or higher for high system resolution. NOTE: All functions of the LT controller are available here in the Line Tracker software. Some functions of the Line Tracker software are not available in the LT controller.

11. www.accesslaserco.com 5603 47 th Ave NE, Marysville, WA 98270, USA 360-651-6141 Computer interface /data logging Both power and voltage are set to a full range of 0 to 1024, arbitrary units. When AutoSave is on files are saved as filled, with a time stamp in the file name. Data files are.csv format for easy importing into Excel. Laser is stabilized in the close-loop mode by moving the length of the resonator along the falling edge or the rising edge. Scale factor in effect If manual setting is not entered by pressing the return key it will not take effect File size indicates the number of data sets per file. Maximum 3600. Make sure to select the appropriate serial port before starting operation

12. www.accesslaserco.com 5603 47 th Ave NE, Marysville, WA 98270, USA 360-651-6141 Close loop operation After profiling this yellow setting line becomes a cross. Move the cross to approximately 10% below the desired peak on the power curve, select the appropriate edge, then press the start tracking button. The laser will start to be tracked and stabilized. Notice that the piezo voltage (blue curve) moves up and down to keep the laser power (red curve) steady.

13. www.accesslaserco.com 5603 47 th Ave NE, Marysville, WA 98270, USA 360-651-6141 Line Tracker- Auto Version With this version of software chose Closed loop on the control box and the system starts to search for a lockable position When it finds a lockable position it goes into closed-loop mode. When the piezo reaches end of travel it will restart searching for a lockable position. During this time an out of lock signal is given from the controller and displayed on the screen. This version of software does not allow control from computer. All controls are performed from the controller box. The software allows for display and data logging.