Download presentation
Presentation is loading. Please wait.
Published byCaroline Gaynor Modified over 10 years ago
1
Simple piezoresistive pressure sensor
2
Simple piezoresistive accelerometer
3
Simple capacitive accelerometer Cap wafer may be micromachined silicon, pyrex, … Serves as over-range protection, and damping Typically would have a bottom cap as well. C(x)=C(x(a)) Cap wafer
4
Simple capacitive pressure sensor C(x)=C(x(P))
5
ADXL50 Accelerometer +-50g Polysilicon MEMS & BiCMOS 3x3mm die Integration of electronics!
6
ADXL50 Sensing Mechanism Balanced differential capacitor output Under acceleration, capacitor plates move changing capacitance and hence output voltage On-chip feedback circuit drives on-chip force-feedback to re- center capacitor plates (improved linearity).
7
Analog Devices Polysilicon MEMS
8
ADXL50 – block diagram http://www.analog.com/en/mems-and-sensors/imems-accelerometers/products/index.html
9
Sense Circuit Electrostatic Drive Circuit Proof Mass Digital Output MEMS Gyroscope Chip Rotation induces Coriolis acceleration J. Seeger, X. Jiang, and B. Boser halteres
10
MEMS Gyroscope Chip 1 m Drive 0.01 Å Sense J. Seeger, X. Jiang, and B. Boser
11
Two-Axis Gyro, IMI(Integrated Micro Instruments Inc.)/ADI (fab)
12
Single chip six-degree-of-freedom inertial measurement unit (uIMU) designed by IMI principals and fabricated by Sandia National Laboratories
13
TI Digital Micromirror Device
14
www.dlp.com
16
NEU/ADI/Radant/MAT Microswitches SEM of NEU microswitch Drain Source Gate Beam Drain Gate Source Beam Drain Gate Source Surface Micromachined Post-Process Integration with CMOS 20-100 V Electrostatic Actuation ~100 Micron Size MAT Microswitch http://www.radantmems.com/radantmems/switchoperation.html
17
Contact End of Switch Contact Detail
18
Packaged Plasma Source Top View Side View Die in Hybrid Package
19
Fabrication SEM of Interdigitated Capacitor Structure
20
12/19/2014 Spectrometer cross-section Surface Micromachined Spring System Electrostatic Actuator Plates
21
12/19/2014 Fabricated Microspectrometers
22
Intensity vs. Wavelength =515 nm =515 nm FWHM = 25nm RP = 21 = 575nm FWHM = 30nm RP = 20 =625nm =625nm FWHM = 39nm RP = 16
23
Figure 1. Qualcomm Mirasol Display IMOD Structure Showing Light Reflecting off the Thin-film Stack and Mirror Interfering to Produce Color.
24
Optical MEMS Vibration Sensors Uniform cantilever beamFoster Miller - Diaphragm Cantilevered paddleCantilevered supported diaphragm
25
Optically interrogated MEMS sensors 55 m length cantilevered paddle after 7 hours of B.O.E. releasing and lifted up with a 1 m probe (~0.35 m thick, 2 m gap)
26
Courtesy Connie Chang-Hasnain
28
Micromachining Ink Jet Nozzles Microtechnology group, TU Berlin
29
Microfluidic Chips
30
(UCLA, Fan)
31
(Gruning)
32
Gene chips, proteomics arrays.
33
NEMS: TOWARD PHONON COUNTING: Quantum Limit of Heat Flow. Roukes Group Cal Tech Tito
34
From Ashcroft and Mermin, Solid State Physics.
35
Other: NSF-Funded NSEC, Center for High-Rate Nanomanufacturing (CHN): High-rate Directed Self-Assembly of Nanoelements Nanotemplate: Layer of assembled nanostructures transferred to a wafer. Template is intended to be used for thousands of wafers. Nanotube Memory Device Partner: Nantero first to make memory devices using nanotubes Properties: n onvolatile, high speed at 10 15 cycles), resistant to heat, cold, magnetism, vibration, and cosmic radiation. Proof of Concept Testbed
36
Switch Logic, 1996, Zavracky, Northeastern InverterNOR Gate
37
Simple Carbon Nanotube Switch Diameter: 1.2 nm Elastic Modulus: 1 TPa Electrostatic Gap: 2 nm Binding Energy to Substrate: 8.7x10 -20 J/nm Length at which adhesion = restoring force: 16 nm Actuation Voltage at 16 nm = 2 V Resonant frequency at 16 nm = 25 GHz Electric Field = 10 9 V/m or 10 7 V/cm + Geom. (F-N tunneling at > 10 7 V/cm) Stored Mechanical Energy (1/2 k x 2 ) = 4 x 10 -19 J = 2.5 eV 4 x 10 -19 = ½ CV 2 gives C = 2 x 10 -19 F << electrode capacitance! Much more energy stored in local electrodes than switch.
38
NEMS Switch Fabrication: To be discussed. (a) Silicon chip with 500 nm of thermally grown oxide, 20 nm of tungsten, and PMMA. (b) Electron beam lithography was used to define features in the PMMA layer. An ICP etch was used to pattern the tungsten and etch down into the oxide. (c) A Cr/Au layer was evaporated and lifted off by removing the tungsten. (d) DEP was performed to assemble a small bundle of nanotubes traversing the trench between the two side electrodes.
39
NEMS Switch Operation (a) Scanning electron micrograph of a switch. Atomic force microscopy scans before (b) and after (c) switch actuation. (d) Initial (solid lines), second (dashed lines), and third (dotted lines) I-V sweeps for the device seen in (a-c). This device had a vertical gap of 24 nm and a trench width of 195 nm.
40
NEMS Switch Problems During Operation
41
NEMS Switch Electro-Mechanical Model
42
Carbon Nanotube for Adhesion Measurement
43
Biological Nanomotor
Similar presentations
© 2025 SlidePlayer.com. Inc.
All rights reserved.