1. Water Hydraulic Valves
Introducing our range of
Water Hydraulic Valves
For control of Main Inlet Valve
Servo motor, service & maintenance seals
Pressures up to 120 bar
Flow rates up to 600 litres/min
316L Stainless Steel Construction

2. Water Hydraulic Control Valves
The 6mm Water Hydraulic Control valve is a ball seated type valve. The stainless steel / ceramic ball seat design ensures a virtual leak tight shut off.
M.T.B.F., SFF, PFD and SIL Data (Available upon request)
Easy Installation, Repair and Replacement
Stainless Steel Construction
Up to 120 bar Operating Pressure Range
General Description
The DN6 valve design incorporates a balanced internal piloting system and a lever mechanism to enable a wide range of operators to operate the valve.
All valves have an ‘O’ Ring interface that enables them to be fitted with BSP.P ported subplates as standard, or manifold mounted to reduce pipework, fittings, weight and space. This interface also allows direct mounting of the valve to larger pilot operated valves up to the DN25, increasing the flow capacity to 200 l/min.
By removing just 4 bolts the valves can be dismounted without disturbing pipework and possibly contaminating the hydraulic system. Blanking and flushing plates can also be supplied.

3. Water Hydraulic Control Valves
Construction Materials
Valve bodies and subplates: 316L Stainless Steel
Wetted parts: Various grades of Stainless Steel/Super Duplex / Ceramic/Aluminium Bronze
Seal Nitrile / Buna N / PTFE / Polyurethane
Fasteners: A4, grade 80 stainless steel
Springs: stainless steel
Operating Temperature Range
Standard: 5 ºC to + 60 ºC
Ingress Protection (solenoids valves )
IP54
Operating Pressure Range
15 to 120 bar
Operating Medium
Filtered Fresh Water
Recommended Filtration
DN6: microns
DN15: 25 microns
DN25: 25 microns
DN40: 200 microns

4. Water Hydraulic Control Valves
Solenoid Operated with Hydraulic Override Pilot
2 port, 2 position
3 port, 2 position
120 bar max. pressure
Flow rates up to 20 l/min
Stainless Steel construction
24VDC, 110VDC, 220VDC
Override signal, oil or water
Hydraulic Pilot Operated
2 port, 2 position
3 port, 2 position
15 to 120 bar pressure range
Flow rates up to 20 l/min
Stainless Steel construction
Pilot media, Oil or Water
Plunger or Roller Cam Operated
2 port, 2 position
3 port, 2 position
15 to 120 bar pressure range
Flow rates up to 20 l/min
Stainless Steel construction

5. Water Hydraulic Control Valves
Solenoid Operated
3 port, 2 position
Flow rates up to 20 l/min
15 to 120 bar working pressure
Stainless Steel construction
DN40 - Hydraulic Pilot Operated
3 port, 2 position
5 port, 2 position
Pressure range 15 to 120 bar
Flow rate up to 600 l/min
Stainless Steel construction
Pilot media, Oil or Water
Remote position sensors
1 ½ “ SAE 3000 psi Flanged connections or BSP.P threaded ports
Block before bleed function
Operating temperature range 5 ºC to + 60 ºC
DN15 & DN25
Solenoid operated
Oil or Water pilot operated
3 port, 2 position
4 port, 2 position
Pressure range 15 to 120 bar
Flow rates up to 200 l/min
Stainless Steel construction
Pilot media, Oil or Water
Easily replaceable one piece cartridge valve design

6. Water Hydraulic Control Valves
Keep it simple !
Water Hydraulic Control Valves can simplify hydraulic control circuits and therefore increase reliability, while reducing maintenance and capital costs.
Water Hydraulic Control Valves can replace conventional oil hydraulic power units and oil servo valves by utilizing the valuable natural renewable energy resource of water.