1. The Best Solution for CIPP American Made, American Support Introducing America’s First UV Cured Fiberglass CIPP

2. Test Results 4MM 8” StreamlinerUV™ Liner Flexural strength: 52,000 PSI 50 year flexural strength: 33,840 PSI (65% retention) Flexural modulus: 1,700,000 PSI 50 year flexural modulus: 1,160,240 PSI (68% retention) 3MM 8” StreamlinerUV™ Liner Flexural strength: 47,000 PSI Flexural modulus: 1,350,000 PSI

3. Water Tight:100% leak proof* No Shrinkage:0.0% loss* Thin Wall:From 3mm Cured:Ultra Violet Light Curing Speed:7.5ft per minute (8” ) Laterals:No seals or grouting required Flow:Hazen-Williams C=150 *2009 IKT Liner Report, (Institute for Underground Infrastructure)

4. Polyester outer containment and protection foil. Chemical and temperature resistant 7 layer polyethylene/polyamine inner containment foil. Multiple layers of high quality E-CR fiberglass. The fiberglass layers are saturated with polyester or vinyl ester resins during manufacturing. Translucent UV resistant outer foil.

5. Clear inner foil is removed. Outer foil remains in the pipe after curing. Proprietary resin “jelling” maintains consistent wall thickness during storage, shipping and installation.

6. Line is bypassed Line is bypassed Upstream manhole is plugged Upstream manhole is plugged Line is cleaned and pre-videoed Line is cleaned and pre-videoed Rope pulled in during pre-video Rope pulled in during pre-video

7. Pre-liner pulled through the pipe with rope inserted from pre-video Pre-liner pulled through the pipe with rope inserted from pre-video Second rope is pulled through pipe with pre-liner. Second rope is pulled through pipe with pre-liner.

8. Liner is delivered to the job site Liner is delivered to the job site Liner is pulled in place by a winch Liner is pulled in place by a winch

9. Safety sleeves are inserted on liner Safety sleeves are inserted on liner End caps are installed on each end of the liner End caps are installed on each end of the liner Liner is inflated and calibrated at 8psi Light Train is inserted and pressure is restored Light Train is inserted and pressure is restored

10. Light Train Camera is activated Light Train Camera is activated Light Train is manually pulled and uncured liner is video inspected Light Train is manually pulled and uncured liner is video inspected Any installation issues are resolved and video is archived.

11. Light Train UV lamps are activated Light Train UV lamps are activated Light Train is pulled via computer control through the liner. Light Train is pulled via computer control through the liner. Speed, temperature and pressure are monitored throughout the curing process.

15. 52,000 PSI Flexural Strength 1.7M PSI Flexural Modulus E-CR Glass Material 9,300 PSI Flexural Strength 448,000 PSI Flexural Modulus Needled Felt Material

16. * D2990 test results StreamLiner UV * *Insituform

17. *2009 IKT Liner Report, (Institute for Underground Infrastructure) 100% water tight* 63% water tight *

18. 0.0% ≤5%

19. 8” 3MM Liner 0% Shrinkage Loss of I.D. 5.8% 8” 6MM Liner 3% Shrinkage Loss of I.D. 15.8%

23. Flexural Mod 448K PSI Flexural Strength of 9300 PSI No pre-cure videos Thicker wall and reduced flow Liner shown to shrink Liner shown to leak Must seal lateral connections Must deal with odor and styrene No Shrinkage No leaking No Lateral Seals needed No odor or curing by-products Flexural Mod of 1.7M PSI Flexural Strength 52K PSI Multiple curing videos Thinner liner and greater flow

24. Review the Streamliner UV specification doc Recommend UV fiberglass as an approved material