Download presentation
Presentation is loading. Please wait.
Published byAlisa Wiltshire Modified over 9 years ago
1
Machine Tools And Devices For Special Technologies Electrochemical machining Slovak University of Technology Faculty of Material Science and Technology in Trnava
2
Electrochemical machining Using only for conductive materials, independence of hardness, toughness,... Anode melding – machining material is anode and tool is cathode, Is not originated thermal and mechanical damaging of material, Little worn-down of tool, The quality is influenced by homogeneity of structure, In comparing of photochemical machining are achieved higher rates of removing of material, shape and dimension accuracy are higher
3
Electrochemical machining Electrolyse is takes place in gap between tool and material where is flowed electrolyte in pressure. High pressure using of electrolyte is accelerated removing of material and quality of surface too. Material removing is most intensive where is the gap smallest – with highest flow intensity. Tool has the shape of asked workpiece.
4
Electrochemical machining electrolyt – solution of HCl, Pressure of electrolyte is 0,5 – 1,5MPa, Speed of electrolyte flowing is around 50 m/sec, Flow intensity is to 1000 A/mm 2, Voltage to 30V, with higher is possible to origin the discharge, Speed of removing is 1 – 3,5 mm 3 /min.A, Feeding till 2 mm/min Particular phase components are impregnated by various speed, that everyone phase components have minimum voltage is that process is stopped.
5
Electrochemical machining
6
Largeness of the gap is 0,1 – 0,3 mm. Higher gap – more slow removing of material and quality of the surface, Lower gap – increased possibility of the short circuits and damaging of material and electrode. Constant gap – it achieved by continuous regulation and from time to time is measured the size of gap and changed the speed of feed (adaptive directing).
7
Electrochemical machining Tool is Cu electrode. Economical is in series production of difficult shape of workpieces. Parts of tool that are not attended in the machining that are isolated. Machines and tools are expensive and that is why used only in the reasonable cases.
8
Electrochemical machining Power of electrochemical machining is amount of melted metal directed by Faraday laws, Removing speed is main factor of electrochemical machinability, Accuracy of machining is depend on between electrode distance generally IT 8 till IT 10, Quality of surface (roughness) depend on the machined material, on concentration of electrolyte, on electric hydraulic parameters, achieved R a 0,2.
9
Electrochemical machining Electrolyt is most often solution of acid or of various salts. Electrolyt is used in concentration 10 till 20%, temperature is around 35 °C. Electrolyt assuring: Direction of electricity, Takes away originated heat and impurities, Melted machined material
10
Electrochemical machining Requests of electrolyte:: High electric conductivity, Is not possible to outflow cations of metal that make to possible to settled in the tool. Must contains ions that melted anode Reaction products that are to possible remove from electrolyte, Low kinematics viscosity to no become useless hydraulic losses, Must be aggressive with respect to machined material and must equally melted all his phase components.
11
Electrochemical machining During machining is acidity of electrolyte fast increased and can become passivation of anode (Fe and Ni alloys). Here is added nitrous acid that is like stabilisator of ph. Removing of waste products from electrolyte.
12
Electrochemical machining Machining by homogeneous electrolyte – gap between electrodes around 0,2 mm, lower that accuracy machining, needed correction of activate part of tool. Machining by mixture electrolyte – substance of electrolyte and air, electrolyte + CO 2, gap can be under 0,1 mm (usually 0,05 – 0,08 mm), higher quality and accuracy of surface in the difficult shapes too.
13
Kinds of electrochemical machining By kinds of removing of melting waste parts we can divided: With flow electrolyte: Inside, outside, Cross, By mechanical removed products of reactions. In the low flow intensity (under the limit of creation of passivity layer) is not possible to removing of waste parts.
14
Kinds of electrochemical machining
16
ECM deeping of holes High flow intensity (1000 A/cm 2 ), High flow speed of electrolyte (around 60/sec), Feed of the tool electrode 0,5 – 10 mm/min, Mixture electrolyte, Roughness of surface R a lower than 2 Hard machining, hard and high strength materials. Voids of dies, turbine vanes,...
17
ECM void deeping
20
ECM drilling We know three base kinds of hole production by ECM: Deeping by form tube (STEM) – tube of form section (shape hole), Electrolytic soft drilling (ECF) – glass tube Electrolytic drilling by flow of electrolyte (ESD) – glass tube with capillary
21
Deeping by form tube
22
Electrolytic soft drilling
23
Electrolytic drilling by flow of electrolyte
24
Electrochemical dividing of material We know the next kinds of ECM dividing of material: By rotary disk – disk electrode has sides covered with isolation, stabile stock removal Slot tool – tool is a tube in that is slot from which is flow out electrolyte, complicated shape cuts. By wire tool – electrode is wire, into the place of cut is directed the electrolyte by hose, thickness to 20mm,
25
ECM dividing material by slot tool
26
ECM dividing material by wire tool
27
Electrochemical machining Removing the burrs – electrolyte is directed to burrs, in the sharp rims is highest intensity, burrs are melted by anode. grinding – combination of anodic melting and mechanical grinding, into electrolyte is mixing in abrasive, polishing – at the top of these raggedness is highest flow intensity, little stock removal, flow intensity around 0,7 A/cm 2, voltage till 12 V, cathode is of plumbum, big gap, macro raggednesses can be increased.
28
Electrochemical machining marking – electrode has the shape of mark, marked place is different of background of deeping about 0,003 to 0,1 mm, marking lasted only some seconds, the force is not influence, heat and deformation too, it used for thin foils, strong and brittle materials.
Similar presentations
© 2024 SlidePlayer.com. Inc.
All rights reserved.