1. FIREFIGHTER I LESSON 12A

2. FIRE HOSE TERMS Expansion-ring gasket Expansion-ring gasket — Gasket used at the end of hose where it is expanded into coupling shank Fire hose Fire hose — Type of flexible tube used to carry water under pressure from source of supply to point where it is discharged Hose bed Hose bed — Hose storage compartment Dutchman Dutchman — Reverse bend at coupling of bedded hose that allows it to be payed out without bending Flake Flake — To lay out fire hose in a loose accordion pattern to reduce chances of hose tangling and kinking when pulled TS 12A–1a

3. FIRE HOSE TERMS (cont.) Shank Shank — That portion of coupling that serves as a point of attachment to the hose Standpipe Standpipe — Wet or dry piping system that provides fire department outlets and private hoseline Storz coupling Storz coupling — Sexless coupling commonly found on large diameter hose Swivel gasket Swivel gasket — Gasket used to make a watertight connection between male and female couplings TS 12A–1b

5. NFPA 1901 PUMPER HOSE REQUIREMENTS Attack hose Attack hose — 400 ft. (122 m) of 1½-, 1¾-, or 2-in. (38 mm, 45 mm, or 50 mm) Supply hose Supply hose — 1,200 ft. (366 m) of 2½-in. (65 mm) or larger Soft-sleeve intake hose Soft-sleeve intake hose — 15 ft. (5 m), large diameter, or hard-suction intake hose — 20 ft. (6 m) TS 12A–2

6. HOSE APPLIANCE VALVES Ball Valves Gate Valves Butterfly Valves Clapper Valves TS 12A–3

7. VALVE DEVICES & HOSE FITTINGS Valve devices Valve devices  Wye appliances  Siamese appliances  Water thief appliances  Large diameter hose appliances  Hydrant valves Fittings Fittings Intake devices Intake devices TS 12A–4

8. HOSE TOOLS Hose roller (hoist) Hose roller (hoist) Hose jacket Hose jacket Hose clamp Hose clamp Spanner, hydrant wrench, and rubber mallet Spanner, hydrant wrench, and rubber mallet Hose bridge or ramp Hose bridge or ramp Chafing block Chafing block Hose strap, hose rope, and hose chain Hose strap, hose rope, and hose chain TS 12A–5

9. HOSE CLAMP USES Prevent charging the hose bed during hose-lay operations Prevent charging the hose bed during hose-lay operations Allow replacement of a burst section without shutting down the water supply Allow replacement of a burst section without shutting down the water supply Allow hoseline extension without shutting down water supply Allow hoseline extension without shutting down water supply Allow advancement of a charged hoseline up stairs Allow advancement of a charged hoseline up stairs TS 12A–6

10. HOSE CLAMP RULES Apply at least 20 feet (6 m) behind apparatus. Apply at least 20 feet (6 m) behind apparatus. Apply approximately 5 feet (1.5 m) from coupling on incoming water side. Apply approximately 5 feet (1.5 m) from coupling on incoming water side. Stand to one side when applying or releasing press-down type. Stand to one side when applying or releasing press-down type. Center hose evenly in jaws to avoid pinching hose. Center hose evenly in jaws to avoid pinching hose. Close and open slowly to avoid water hammer. Close and open slowly to avoid water hammer. TS 12A–7

13. CARE OF FIRE HOSE COUPLINGS Avoid dropping and/or dragging couplings. Avoid dropping and/or dragging couplings. Do not permit vehicles to run over fire hose. Do not permit vehicles to run over fire hose. Examine couplings when hose is washed and dried. Examine couplings when hose is washed and dried. Remove gasket, and twist swivel in warm, soapy water. Remove gasket, and twist swivel in warm, soapy water. Clean threads to remove tar, dirt, gravel, and oil. Clean threads to remove tar, dirt, gravel, and oil. Inspect gasket, and replace if cracked or creased. Inspect gasket, and replace if cracked or creased. TS 12A–8

16. HOSE LOADING GUIDELINES Check gaskets and swivel before connecting any coupling. Check gaskets and swivel before connecting any coupling. Keep flat sides of hose in same plane when connecting two sections. Keep flat sides of hose in same plane when connecting two sections. Tighten couplings hand-tight when two sections are connected. Tighten couplings hand-tight when two sections are connected. Remove wrinkles from hose when it must be bent to form a loop in the hose bed — press with the fingers so that inside bend is smoothly folded. Remove wrinkles from hose when it must be bent to form a loop in the hose bed — press with the fingers so that inside bend is smoothly folded. TS 12A–9a

17. HOSE LOADING GUIDELINES (cont.) During loading, make a short fold or reverse bend in the hose so that couplings do not have to be turned around to be pulled out of bed. During loading, make a short fold or reverse bend in the hose so that couplings do not have to be turned around to be pulled out of bed. Load large diameter hose with all couplings placed at front of bed. Load large diameter hose with all couplings placed at front of bed. Do not pack hose too tightly. Do not pack hose too tightly. TS 12A–9b

18. HOSE LOADING METHODS Coupled and folded into hose bed Coupled and folded into hose bed — Attack and supply lines Preconnected and folded into hose bed — Preconnected and folded into hose bed — Collapsible attack and supply lines Racked, compartmentalized, or secured to apparatus Racked, compartmentalized, or secured to apparatus  Preconnected or unconnected soft-sleeve and hard- suction intake hose  Attack and intake hose that is loaded on raised trays or in tailboard compartments, side bins, or front bumper wells TS 12A–10a

19. HOSE LOADING METHODS (cont.) Preconnected and reel wound Preconnected and reel wound  Noncollapsible booster line  Some large diameter hose  Some attack handlines Tied bundles or rolls Tied bundles or rolls  Standpipe hose  Wildland attack hose TS 12A–10b

21. ACCORDION LOAD Advantages Advantages  Simple design  Easily loaded  Easily shoulder-loaded for carrying Disadvantage Disadvantage — Loaded on edge, subjecting edges to wear from apparatus vibration TS 12A–11

23. HORSESHOE LOAD Advantage Advantage — Fewer sharp bends than accordion or flat loads Disadvantages Disadvantages  In wide hose beds, hose may come out in a wavy, snakelike lay in the street as hose is pulled from one side of the bed to the other  Folds for shoulder carry cannot be obtained as easily as for accordion load  Large diameter hose tends to fall over in bed and may become entangled TS 12A–12

25. FLAT LOAD Advantages Advantages  Easiest to load  Suited to any size supply hose (best way to load large diameter hose)  Folds lie flat rather than on edge so is not subject to edge abrasion Disadvantages Disadvantages  Folds contain sharp bends at both ends  Hose must be reloaded periodically to relocate the bends TS 12A–13

26. PRECONNECTED HOSE LOADS FOR ATTACK LINES Preconnected Flat Load Triple Layer Load Minuteman Load TS 12A–14

29. HOSE LOAD FINISHES Straight Finish Reverse Horseshoe Finish TS 12A–15

32. STRAIGHT HOSE ROLL Used when hose will be placed in storage, especially rack storage Used when hose will be placed in storage, especially rack storage Used when hose will be returned to quarters for washing Used when hose will be returned to quarters for washing Reversed (male coupling exposed) to identify a damaged coupling or hose section Reversed (male coupling exposed) to identify a damaged coupling or hose section TS 12A–16

34. DONUT HOSE ROLL Used when hose is going to be deployed directly from a roll Used when hose is going to be deployed directly from a roll Advantages over straight roll Advantages over straight roll  Both ends are available on the outside of the roll  The hose can be quickly unrolled and placed in service  The hose is less likely to kink or spiral when unrolled  One or two firefighters can perform a donut roll TS 12A–17

36. TWIN DONUT HOSE ROLL Is most adaptable to 1½inch (38 mm) and 1¾-inch (45 mm) hose, though it can be used on hose up to 3 inches (77 mm) Is most adaptable to 1½inch (38 mm) and 1¾-inch (45 mm) hose, though it can be used on hose up to 3 inches (77 mm) Provides a compact roll that can be carried for special applications such as high-rise fires Provides a compact roll that can be carried for special applications such as high-rise fires Creates couplings on the outside of the roll Creates couplings on the outside of the roll Can be coupled together for protection if the couplings are offset Can be coupled together for protection if the couplings are offset Creates its own carrying strap and requires no additional rope Creates its own carrying strap and requires no additional rope TS 12A–18