1. used with FILTERS Copyright © 2013 by The S.E.A. Group

2. CHECK: Correct filter(s) Filter(s) correctly fitted Respirator clean, complete, correctly assembled Fit the SR200

3. Loosen the side straps of the head harness. Twist the strap holders forward and pull on the strap. Copyright © 2013 by The S.E.A. Group Fit the SR200

4. Sling the neck strap around your neck Lift the head harness up over the mask and away from your face Place your chin in the chin cup Copyright © 2013 by The S.E.A. Group Fit the SR200

5. Pull the head harness backwards towards your neck Copyright © 2013 by The S.E.A. Group Fit the SR200

6. Tighten the side straps in pairs by pulling the loose ends Copyright © 2013 by The S.E.A. Group Fit the SR200

7. If necessary, adjust the two top straps. Undo buckles and pull loose ends forwards Fasten the buckles Copyright © 2013 by The S.E.A. Group Fit the SR200

8. Loose ends can be hooked to the head harness Copyright © 2013 by The S.E.A. Group Fit the SR200

9. Fit a filter Screw the filter adapter into the mask Copyright © 2013 by The S.E.A. Group

10. Fit a filter Make sure the filter is turned the correct way (arrows toward mask) Copyright © 2013 by The S.E.A. Group

11. Fit a filter Place filter in the filter attachment Ease the filter securely into the groove Copyright © 2013 by The S.E.A. Group

12. Fit a filter Place a pre-filter in the pre-filter holder Copyright © 2013 by The S.E.A. Group

13. Fit a filter Snap the pre-filter onto the main filter Copyright © 2013 by The S.E.A. Group

14. Quick clean Use warm soapy water and a clean soft cloth, or a Sundström cleaning tissue Inspect and wipe the outside of the mask and visor You can leave the head harness on Check that there are no cracks or other damage Copyright © 2013 by The S.E.A. Group

15. Quick clean Use warm soapy water and a clean soft cloth, or a Sundström cleaning tissue Wipe the inside of the mask, including the visor Pay special attention to ‘nooks and crannies’ inside the respirator Make sure the face rims and chin cup are clean Copyright © 2013 by The S.E.A. Group

16. Quick clean Replace the pre-filter with a new one and snap onto the main filter Copyright © 2013 by The S.E.A. Group

17. Quick clean Store the assembled respirator in a sealed container away from any contaminants Copyright © 2013 by The S.E.A. Group

18. Thorough clean First, perform a quick clean Copyright © 2013 by The S.E.A. Group

19. Thorough clean Remove the filter and wipe the inside of the filter adapter Pay special attention to the groove and the rim of the filter adapter Copyright © 2013 by The S.E.A. Group

20. Thorough clean Remove the filter adapter Copyright © 2013 by The S.E.A. Group

21. Thorough clean Remove each exhalation valve cap Gently pull the membrane out Copyright © 2013 by The S.E.A. Group

22. Thorough clean Carefully clean the membranes and the valve seats No dirt or grime must remain, and the parts must not have any cracks, tears or other damage Copyright © 2013 by The S.E.A. Group

23. Thorough clean Reassemble the membranes and valve caps Copyright © 2013 by The S.E.A. Group

24. Thorough clean Gently pull out the three inhalation membranes from inside the mask Clean all the membranes and the valve seats Replace the membranes Copyright © 2013 by The S.E.A. Group

25. Thorough clean If the head strap is very dirty or grimy, detach it and clean it separately Copyright © 2013 by The S.E.A. Group

26. Thorough clean Store the assembled respirator in a sealed container away from any contaminants Copyright © 2013 by The S.E.A. Group

27. Thank you for watching Copyright © 2013 by The S.E.A. Group