Download presentation
Published byOrlando Peller Modified over 10 years ago
1
Modern Automotive Technology PowerPoint for by Russell Krick
Publisher The Goodheart-Willcox Co., Inc. Tinley Park, Illinois
2
Chapter 14 Engine Bottom End Construction
3
Contents Cylinder block construction Piston construction
Piston ring construction Piston pin construction Connecting rod construction Crankshaft construction Engine bearing construction Rear main bearing oil seal construction Select-fit parts Balancer shafts
4
Includes the block, crankshaft, connecting rods, and piston assemblies
Engine Bottom End Includes the block, crankshaft, connecting rods, and piston assemblies
5
Cylinder Block Construction
Engine cylinder blocks are normally made of cast iron or aluminum Cast iron is very heavy and strong Aluminum is relatively light and dissipates heat well
6
Cylinder Block Cylinders may be integral parts of the block or formed by pressed-in liners
7
Cylinder Sleeves Metal, pipe-shaped inserts that fit into the cylinder block act as cylinder walls Cast iron sleeves are commonly used in aluminum cylinder blocks Sleeves can also be installed to repair badly damaged cylinder walls in cast iron blocks
8
Cylinder Sleeves There are two basic types of sleeves: dry sleeves
wet sleeves
9
Dry Sleeve Presses into a cylinder that has been bored oversize
Made from relatively thin material Not exposed to engine coolant The outer surface touches the walls of the cylinder block
10
Wet Sleeve Exposed to the engine coolant
Thicker construction than a dry sleeve Designed to withstand combustion pressure and heat without the added support of the cylinder block
11
Sleeve Installations Dry sleeve Wet sleeve
12
Aluminum cylinder block with pressed-in, cast iron wet sleeves
Sleeve Installations Aluminum cylinder block with pressed-in, cast iron wet sleeves
13
Line Boring Machining operation that cuts a series of holes through the block for the crankshaft or camshaft bearings Holes must be in perfect alignment for the crankshaft or camshaft to turn freely
14
Two- and Four-Bolt Mains
Two-bolt main block uses two cap screws to secure each main bearing cap to the block Four-bolt main block uses four cap screws to hold each main cap used on high-performance engines with extra bolts, the block can withstand more crankshaft downward pressure
15
Crossbolted Block Has extra cap screws going in through the sides of the block and main caps for added strength Often used on high-performance engines
16
Block Girdle Also called a main bearing bedplate
Large one-piece cap that fits over the entire bottom of the block All the main caps are formed as one piece to increase strength and block stiffness
17
Piston Construction Pistons are normally cast or forged from an aluminum alloy Cast pistons relatively soft, used in slow-speed, low-performance engines Forged pistons used in fuel-injected, turbocharged, and diesel engines
18
Piston This piston is for a diesel engine and has a groove that allows an oil spray to help cool the piston
19
Piston Dimensions
20
Cam-Ground Piston Slightly out-of-round when viewed from the top
Machined a few thousandths of an inch larger in diameter perpendicular to the piston pin centerline compensates for different rates of expansion due to differences in metal wall thickness
21
Cam-Ground Piston
22
Cam-Grind Theory As the piston is heated, the thicker area around the pin boss causes the piston to expand more parallel to the piston pin The piston becomes round when hot A cam-ground piston maintains the correct piston-to-cylinder clearance when cold and at operating temperature
23
Piston Taper Used to maintain the correct piston-to-cylinder clearance
The top of the piston is machined slightly smaller than the bottom Since the piston head gets hotter than the skirt, it expands more The piston is almost equal in size at the top and bottom at operating temperature
24
Piston Taper
25
Piston Shape Refers to the contour of the piston head
Piston head is shaped to match and work with the shape of the combustion chamber Piston may have a flat top or a domed head
26
This is a piston for a diesel engine having a direct injection nozzle
Piston Shape This is a piston for a diesel engine having a direct injection nozzle
27
Slipper Skirt Produced when the portions of the piston skirt below the piston pin ends are removed Provides clearance between the piston and the crankshaft counterweights Piston can slide farther down in the cylinder without hitting the crankshaft
28
Slipper Skirt Piston
29
Variable Compression Piston
A two-piece design controlled by engine oil pressure The piston head fits over and slides on the main body of the piston Engine oil pressure is fed between the two halves to form a hydraulic cushion
30
Variable Compression Piston
With normal driving, oil pressure extends the top of the piston for maximum compression ratio and power When engine speed increases, combustion pressure pushes the head down to lower the compression ratio prevents engine knocking and pinging
31
Piston Ring Construction Automotive pistons normally use three rings:
two compression rings one oil ring
32
Compression Rings Prevent pressure leakage into the crankcase
Wipe some of the oil from the cylinder walls Usually made of cast iron An outer layer of chrome or other metal may be used to increase wear resistance
33
Compression Rings
34
Oil Rings Keep crankcase oil out of the combustion chambers
Available in two basic designs: rail-spacer type (three piece) one-piece type
35
Oil Rings Rail-spacer ring (most common)
One-piece ring made from cast iron
36
Piston Ring Dimensions
37
Piston Ring Gap Distance between the ends of the ring when installed in the cylinder Allows the ring to be installed on the piston and to “spring” outward in its cylinder Allows the ring to conform to any variation in the cylinder diameter due to wear
38
Most piston rings use a butt joint
Piston Ring Gap Most piston rings use a butt joint
39
Piston Ring Coatings Soft ring coatings Hard ring coatings
porous metal, such as iron help the ring wear in quickly the outer surface will wear away rapidly so the ring conforms to the shape of the cylinder Hard ring coatings chrome or moly increase ring life and reduce friction used in new or freshly machined cylinders
40
Piston Pin Construction
Piston pins are normally made of case-hardened steel, which increases the wear resistance A hollow piston pin is machined and polished to a very precise finish
41
Piston Pins Piston pins are held in the piston by one of two means:
snap rings (full-floating piston pin) press-fit
42
Full-Floating Piston Pin
Secured by snap rings Free to rotate in both the rod and piston
43
Press-Fit Piston Pin Forced tightly into the connecting rod’s small end and free to rotate in the piston pin hole
44
Piston Pin Offset Locates the piston pin hole slightly to one side of the piston centerline Helps quiet the piston during use The piston pin hole is moved toward the piston’s major thrust surface the thrust surface is the surface of the piston that is pushed tightly against the cylinder wall during the power stroke
45
The piston notch indicates the front of the piston
Piston Assembly The piston notch indicates the front of the piston
46
This piston has a full-floating piston pin
Piston Assembly This piston has a full-floating piston pin
47
Connecting Rod Construction Most connecting rods are made of steel
Connecting rods normally have an I-beam shape for a high strength-to-weight ratio
48
Connecting Rod Features
Oil spurt holes provide added lubrication for the piston pin, cylinder walls, and other parts Drilled rod allows oil to enter the clearance between the pin and bushing
49
Connecting Rod Features
A. Oil spurt holes B. Drilled rod
50
Connecting Rod Numbers
Ensure that each connecting rod is in the proper location and that the rod cap is installed on the corresponding rod body correctly
51
Broken-Surface Rod The rod is scribed and broken off when manufactured
Produces a rough, irregular mating surface between the rod and cap Done to help lock the rod and cap into alignment
52
Powdered Metal Forging
Forms the rough shape of the part out of metal powder before final shaping in a powerful forge Helps control the shape and weight while reducing machining
53
Machined Block Forging
Involves initial turning in a lathe to bring the blank of metal to size before forming it in a drop forge Helps eliminate flashing flashing is a small blip of rough metal produced when the two halves of the forge come together to “smash” the metal into shape
54
Crankshaft Construction
Engine crankshafts are usually made of cast iron or forged steel Forged steel crankshafts are needed for heavy-duty applications turbocharged engines diesel engines
55
Crankshaft Oil Passages
56
Crankshaft Oil Flow Oil enters the crankshaft at the main bearings and passes through holes in the main bearing journals Oil then flows through passages in the crankshaft and out to the connecting rod bearings
57
Engine Bearing Construction
There are three basic types of engine bearings: crankshaft main bearings connecting rod bearings camshaft bearings
58
Engine Bearings
59
Bearing Construction Steel is used for the body.
Alloys are plated over the backing to form the bearing surface.
60
Bearing Crush Used to help prevent the bearing from spinning inside its bore The bearing is made slightly larger than the bearing bore When the rod or main cap is tightened, the bearing ends press against each other, locking the bearing in place
61
Bearing Crush
62
Bearing Spread Used on split-type engine bearings to hold the bearing in place during assembly The distance across the parting line of the bearing is wider than the bearing bore bearing spread causes the bearing insert to stick in its bore when pushed into place
63
Standard Bearing Has the original dimensions specified for a new, unworn, or unmachined crankshaft May have the abbreviation “STD” stamped on its back
64
Undersize Bearing Used on a crankshaft journal that has been machined to a smaller diameter Available in undersizes of 0.010", 0.020", 0.030" and sometimes 0.040" Undersize is normally stamped on the back of the bearing
65
This bearing is for a journal that has been machined 0.010" undersize
Undersize Bearing This bearing is for a journal that has been machined 0.010" undersize
66
Bearing Positioning A. Spread B. Lug C. Dowel
67
Bearing Oil Holes and Grooves
Holes allow oil to flow through the block and into the clearance between the bearing and the journal Grooves provide a channel so oil can completely encircle the bearing before flowing over and out of it
68
Bearing Oil Holes and Grooves
69
Main Thrust Bearing and Washers
limits crankshaft end play thrust flanges are formed on the main bearing sides, almost touching the thrust surfaces machined on the crankshaft Thrust washers used instead of a thrust bearing to limit crank end play
70
Main Thrust Bearing and Washers
71
Washers slide into place between the crankshaft and block
Thrust Washers Washers slide into place between the crankshaft and block
72
Rear Main Bearing Oil Seal Construction
The rear main bearing oil seal prevents oil leakage around the back of the crankshaft
73
Rear Main Bearing Oil Seal
There are several different types of seals These types include: two-piece neoprene one-piece neoprene wick or rope seal
74
Two-Piece Neoprene Seal
Has a lip to trap oil and another lip that keeps dust and dirt out of the engine
75
Two-Piece Neoprene Seal
The seal fits into a groove cut into the block and rear main cap
76
One-Piece Neoprene Seal
The seal fits around the rear flange on the crankshaft
77
Wick Rear Oil Seal Woven rope filled with graphite
One piece of the rope seal fits into a groove in the block Another piece fits in a groove in the main cap Not as common on modern vehicles as one- and two-piece neoprene seals
78
Select-Fit Parts Parts that are selected and installed in a certain position to improve the fit or clearance between parts pistons are commonly selected to fit precisely into their cylinders Because of select-fit parts, it is important that you reinstall parts in their original locations
79
Balancer Shafts Used in some engines to cancel the vibrating forces produced by crankshaft, piston, and rod movement Usually found on 4- and 6-cylinder engines Usually, a chain is used to turn the shafts at twice crankshaft rpm
80
Shafts are supported on bearings and lubricated by pressurized oil
Balancer Shafts Shafts are supported on bearings and lubricated by pressurized oil
Similar presentations
© 2025 SlidePlayer.com. Inc.
All rights reserved.