1. COMPACT HIGH POWER LASER DAZZLER™ (CHPLD)
INITIAL TRAINING PRESENTATION
29 Oct 07

2. TOPICS Introduction 3-7 Warnings/Safety 8-9 Specifications 10
Nomenclature 11
Battery Replacement 12
On-Off Push Button 13
Intermittent Button Switch 13
Remote Switch Tail Module 14
Make Safe When Not In Use 15
Delrin Fixture 16
Diffuser 17
Cleaning 18-19
Tips 20
Questions 21
29 Oct 07

3. CHP LASER DAZZLER™
A Portable, Non-Lethal, Eye-Safe, Multi-Purpose Device Effective Both Day and Night
29 Oct 07

4. CHP LASER DAZZLER™
It is the most rugged/powerful/compact laser device available that is suitable for this purpose
The CHPLD engages the target in a wall of green laser (532nm) light, which disorients and distracts the subject
This is accomplished by overloading the optic nerve rendering the subject nearly sightless for a short period of time – there is no doubt the individual will see the CHPLD, even in bright sunlight at 200 meters
29 Oct 07

5. CHP LASER DAZZLER™
Specifically designed for applications where gaining the instant attention of individuals in varying light conditions including clear, bright sunny days is critical
IDEAL FOR CONVOY AND ENTRY CONTROL OPERATIONS
Immediate recognition by approaching vehicles or pedestrians which avoids the use of lethal force due to confusion or unseen /unrecognized hand signals
29 Oct 07

6. Drivers approaching a convoy or checkpoint may not see hand signals or realize they are entering a restricted/danger zone
CHPLD at 100 yards – bright daylight
They cannot fail to see the CHPLD even if distracted by traffic, sunlight, pedestrians, or other activities
29 Oct 07

7. Front view showing 4 lasers
OTHER USES
Mark your position and identify friendly units at long distances
Distraction & disruption of hostile groups
Counter sniper
Block line of sight when approaching target
Counter surveillance
Mounted on Tripod
Front view showing 4 lasers
29 Oct 07

8. WARNINGS/SAFETY
Laser Dazzlers™ are non-lethal devices, HOWEVER, with the potential for permanent eye damage if used improperly the CHPLD should always be TREATED LIKE A LOADED WEAPON
DO NOT point this device at any person unless it is operationally required
The user is solely responsible for the safe operation of the CHPLD and for adhering to the instructions and warnings provided
DO NOT look at the CHPLD thru optical devices such as binoculars or telescopes
This device has sufficient energy densities to cause irreversible eye damage and or permanent blindness if used on a subject at close distances or reflected onto a subject’s eyes from a highly reflective surface
29 Oct 07

9. WARNINGS/SAFETY
DO NOT use on subjects at distances closer than 20 meters or reflect back on subjects at distances equivalent to 20 meters or closer without the holographic diffuser installed
DO NOT use on subjects at distances closer than 3 meters or reflect back on subjects at distances equivalent to 3 meters or closer with the with the holographic diffuser installed
The CHPLD is powered by lithium sulfur dioxide primary batteries and are therefore NOT RECHARGEABLE
DO NOT attempt to charge the battery pack. Any attempt to do so is dangerous
29 Oct 07

10. SPECIFICATIONS 500 Milliwatt, 532nm (green) flashing laser
Overall length - 11 inches
Maximum diameter inches
Powered by lithium sulfur dioxide primary batteries
BATTERIES ARE NOT RECHARGABLE
Safe Ranges
Minimum eye safe range – 20 meters (Without holographic diffuser)
Minimum eye safe range – 3 meters (With holographic diffuser)
Maximum effective range:
200 meters – bright sunlight
2 kilometers – night
Construction:
Anodized aluminum
Weight – 2.0 lbs.
Weight as shown – 2.6 lbs.
All parts produced in the USA
Operating Conditions:
All-weather, general purpose and water tight
29 Oct 07

11. NOMENCLATURE
Aiming Device
DELRIN FIXTURE
CHPLD
29 Oct 07

12. BATTERY REPLACEMENT Unscrew tail module
Install battery positive end first
Rotate battery for best fit when installing
Check to confirm O-Ring (3) is still in place
DO NOT over tighten switch module
29 Oct 07

13. INTERMITTENT BUTTON SWITCH
ON-OFF PUSH BUTTON
Push and release to turn on
Push and release again to turn off
INTERMITTENT BUTTON SWITCH
Operate laser by push and release of intermittent button switch
29 Oct 07

14. REMOTE SWITCH TAIL MODULE
This module contains an electronic switch circuit powered by a capacitor which is charged by the battery pack when the laser is OFF
INITIAL CHARGE REQUIRES 4 MINUTES
The laser can be operated for 45 minutes continuously from the initial charge
When the laser is turned off the capacitor is fully charged
The cable connectors for this module are male/female pin type
Mate each connector
Secure by gently rotating the locking collar until it engages the mating part
Rotate clockwise approximately 1/8 of a turn to lock in place
29 Oct 07

15. MAKE SAFE WHEN NOT IN USE
Integral On-Off Push Button Switch Module
Unscrew ¼ to ½ turn
Press button to ensure laser does not fire
If necessary unscrew additional ¼ turn increments until laser will not fire
Remote Switch Tail Module
Disconnect cable connectors
DO NOT unscrew module since the capacitor charge may dissipate and the initial charge time (4 minutes) would be required to operate the laser
Press button switch to ensure laser does not fire
Long Period of Non-use
Remove battery pack
Reinstall Tail Switch Module to prevent dirt and moisture from entering the device
29 Oct 07

16. DELRIN FIXTURE
The laser is provided in the Delrin Fixture and sighted to the red dot reticule scope.
An intermittent on/off button is built into the fixture and is armed by connecting the cable on the Tail Module to the mating connector on the Delrin Fixture
Secure by gently rotating the locking collar until it engages the mating part
Rotate clockwise approximately 1/8 of a turn to lock in place
29 Oct 07

17. DIFFUSER
Adding the provided Holographic Diffuser reduces the minimum eye safety distance from 20 meters to only 3 meters
Unscrew window module
Remove white washer
Place diffuser on window
Reinstall white nylon washer
Reinstall module on device
29 Oct 07

18. CLEANING Remove the laser from the Delrin Fixture Disconnect cable
Remove the Tail Module
Loosen the 6-32 set screws
Slide the laser forward
Make sure not to lose the O-Ring (3)
It is not necessary to remove the set screws
To reinstall just reverse the process
29 Oct 07

19. CLEANING Window With device front facing down unscrew window module
Remove white nylon washer
Turn module over and clean surface underneath
The window & O-Ring will drop out
Clean window with appropriate cleaner such as Windex® sprayed onto a cloth
Reinstall in reverse order
Make sure O-Ring (1) is in the groove
Make sure O-Ring (2) is still on the laser body
CHPLD
Wipe with damp cloth and or a cleaner such as Windex® sprayed onto the cloth
DO NOT immerse in water or cleaning fluids
NO OTHER FIELD DISASSEMBLY OF THE LASER OTHER THAN AS DESCRIBED ABOVE IS PERMITTED. DOING SO WILL DAMAGE THE DEVICE AND VOID THE WARRANTY
29 Oct 07

20. TIPS TIPS FOR EFFECTIVE USE
Individuals or groups: Aim at the center of the chest then raise the beam to eye level for a very short period of time – repeat as necessary
Vehicles: Aim at the center of the windshield then move to the drivers side for a very short period of time – repeat as necessary
29 Oct 07

21. Easily seen at 1 mile in bright sunlight
QUESTIONS ?
Easily seen at 1 mile in bright sunlight
29 Oct 07