1. 7847i Internet Communication Module

2. Agenda Introduction Overview of the 7847i / 7847iE Communication Path
Features
Summary of connections
Before You Leave the Shop
Network Connectivity
Programming the Device
Registering the Device
Updating Code

3. Introduction
The 7847i delivers highly secure, reliable, Internet communication of alarm data while the 7847i-E is suitable for enterprise private network applications using local LAN or point to point connections.

4. Applications Banking Institutions Jewelry Industry Federal Government
Medical
Industrial
Residential

5. Features Secure IP Reporting Dialer Capture Ready
Universal Control Panel Compatibility
Full Contact ID or ADEMCO High Speed Reporting
Six Input Zones
Tamper Protected Enclosure
Remote Services Capability*
Network Friendly
Ease of installation
Upload/Download

6. Wiring the 7847i/7847i-E
Wiring for ECP, 4204 and Two-4204 Modes
Connect the 7847i/7847i-E to a compatible Honeywell VISTA control panel's ECP terminals,
in parallel with keypads and other peripheral devices
Wiring connections for ECP or 4204 modes

7. Wiring the 7847i/7847i-E Wiring a LynxR-I for ECP Mode
To trip the zone on the 7847i/7847i-E in V+ trigger mode, the positive triggering voltage from
the control panel must be within 2.0V-14V.
To trip the zone on the 7847i/7847i-E in V- trigger mode, the negative triggering voltage
must be less than 1.0V.
Note:
Trigger levels above this range may cause permanent damage to the unit.
Trigger levels below this range result in unreliable operation.

8. Wiring the 7847i/7847i-E Wiring for Zone Trigger Mode
To trip the zone on the 7847i/7847i-E in V+ trigger mode, the positive triggering voltage from the control panel must be within 2.0V-14V.
To trip the zone on the 7847i/7847i-E in V- trigger mode, the negative triggering voltage must be less
than 1.0V.
Note:
Trigger levels above this range may cause permanent damage to the unit.
Trigger levels below this range result in unreliable operation.

9. Wiring the 7847i/7847i-E
Primary power for the 7847i/7847i-E is provided by the auxiliary power output of the control panel 9.6V –13.8V, typical, or other external power source.
Zone 1 Input to a LynxR Trigger Output
Zone 1 Input for EOL Supervised N.O./N.C. Triggers

10. Select Programming Option
From AlarmNet Direct
If the device is already in service go to:
If the device is new, choose the appropriate selection:

11. Enabling Remote Services
For A new account enter the following:
Primary City ID
Primary CSID
Primary subscriber
Supervision rate
MAC ID
MAC CRC
Then select:
Enable remote services
Advanced programming
Remember to enable here if using Total Connect

12. With Edit displayed in the Actions box Click GO.
Edit Mode
Status of the device is displayed.
With Edit displayed in the Actions box Click GO.

13. Select Mode and Options
Select Operation Mode
ECP – 4204 Emulation –
2-4204s Emulation – Zone
Select Options
Old Alarm Time
IP Fault Time
Fault Relay Normally On
Tamper Report
Use DHCP
NIC IP Address
Subnet Mask
Gateway IP Address
DNS Server IP Address
Enable Power Save

14. AlarmNet Direct Programming
ECP Mode
Enable Direct Wire Downloading
Keypad Address
Total Connect Features
Remote Access
Keypad Address/Type
Multimode
Multimode Address
Zone 6 and 7
EOLR, V+ or V-
Invert Zone
Zone Restore
Zone Delay

15. AlarmNet Direct Programming
Zone Mode
Trip Inputs 1 or 2 w/Bell out
Increases Trip Voltage to 5V for V+ mode
Lynx Panic
Telco Zone
Open/Close Zone
Multimode
Total Connect
Trigger Type
Invert Zone
Zone Restore
Zone Delay
Zone Report On Arm

16. AlarmNet Direct Programming
4204 Emulation Modes
Fault Relay Normally On
Telco Zone
Open/Close Zone
Enable Direct Wire Downloading
Keypad Address
Total Connect Feature
Remote Access
Keypad Address/Type
Set Multi Partition View
Zone Restore
Zone Delay
Zone Report On Arm
Zone 4 or Zone 8 Arms

17. AlarmNet Direct Programming
If the device is powered and connected to the Internet:
Save And Transfer Data to Device
If the device is not powered or connected to the Internet:
Click “Save”
Click “Exit”
Return to Show Program Devices page.

18. 7720 Programming Tool
The device can also be programmed using a 7720P Programmer.
This 7720P allows access to Useful Diagnostic Tools.

19. 7720P Programming Enters programming mode.
Change Password?
(Y/N)_
Strt Prog Mode?
(Y/N)_
Enters programming mode.
If a password has been previously assigned, this
prompt appears.
Enter a 4-digit password (0-9, A-F, N, S, T, X, Y).
The next prompt appears.
Enter Password
Program Device?
(Y/N)_
NOTE: The central station can remotely block access to local device programming. If this has been done, the following prompt appears:
Access to Prog
Mode Denied

20. Programming In ECP mode, the 7847i/7847i-E communicates with
Press the [space] key to scroll through the modes of operation. Press [ENTER] to select ECP mode.
Device Mode
(ECP)_
ECP
Zone Triggers
4204 Emu
Two 4204s
In ECP mode, the 7847i/7847i-E communicates with
the panel as a Long Range Radio (LRR) device. Enter
the appropriate ECP device address. For controls, see the control panel’s Installation and Setup Guide.
Device Address
(03)_

21. Programming Enter the 2-digit primary city ID, 01-99 (decimal).
(??)_
Enter the 2-digit primary city ID, (decimal).
Enter the 2-digit primary central station ID number, 01-FE (HEX).
Primary CS ID?
(??)_
Primary Sub ID?
(????)_
Enter the 4-digit subscriber account number for the primary central station, (decimal).
2ND CS Y/N?
(N)_
Applicable only if control supports Central Station #1and #2 Category Enable reporting for the LRR device(e.g., VISTA-128BP, FA1660C, etc.).
2ND City ID?
(??)_
Enter the 2-digit secondary city ID, (decimal).
2ND CS ID?
(??)_
Enter the 2-digit second central station's ID number,01-FE (HEX).
2ND Sub ID?
(????)_
Enter the 4-digit subscriber account number for the second central station,

22. Programming
Remote Access Y/N
(N)_
Press [Y] to allow the end user to access their system via a website.
Select "4204 Sourced" to send up to four events or " Sourced" to send eight events. Disable for normal alarm processing and go to Prompt21: "Primary City ID".
Multi Mode
(Disabled)_
Device address must be unique from
the normal LRR Device Address (Prompt 28), and the Keypad Address used for Remote Access or Direct Wire downloading.
Multi Mode Addr
(12)_
Multi-Mode ( notification) is intended as a convenience for the user, and does not replace Central Station reporting of critical events (alarms, troubles, etc.).

23. Programming
Direct Wire Y/N
(N)_
Applies only to VISTA-128BP/250BP and FBP Series controls, and FA1600C and FA1700C Series controls.
Must be programmed if using either the Remote Access feature or Direct Wire downloading. Enter the appropriate device address.
Keypad Address
(28)_
The AlarmNet network must hear at least one supervisory message from the module during this supervision period; otherwise, AlarmNet notifies the central station that a communication failure has occurred.
Supervision
(24 Hours)_
24 Hours
• 1 Hour
• US UL Line (6 Min)
• CN UL Line Lvl 3 (3 Min)
• US UL Line (90 Sec)
• CN UL Line Lvl 4 (90 Sec)
• CN UL Line Lvl 5 (75 Sec)
• None
• 30 Day

24. UL NOTE: Must be 10 Minutes
Programming
Old Alarm Time
(10 Minutes)_
Sets how long an undeliverable alarm is retried for delivery to the central station.
Enter the time delay (01-99) in minutes before the
7847i/7847i-E notifies the control panel that there is
loss of contact with the network.
The fault open collector output is normally
energized to ground, and de-energizes (open circuit) in the event of a module fault.
Allows the Cover Tamper to be disabled/enabled.
UL NOTE: Must be 10 Minutes
IP Flt Time
(60 mins)_
Flt Rel ON Y/N
(N)_
Tamper Rpt Y/N
(Y)_

25. Programming Mode
Use DHCP Y/N
(Y) _
If using DHCP the screens below will not be shown. It will skip to the “PWR Save Mode” question.
NIC IP Address: _
Subnet Mask: _
The Use DHCP option will only be displayed on the 7845i_GSM,
DHCP Dynamically allocates the IP address, this is the recommended option.
If you can use DHCP then press enter to skip to Review.
If you can not use DHCP on the network, then enter no and obtain the following information from your IT administrator.
NIC IP address, Subnet Mask, Gateway IP address and the DNS Server IP address.
Key in the numbers obtained, To enter the dot you will press the star key.
After programming all 4 locations Review will be displayed.
By selecting yes to review allows you to verify all programming locations.
Gateway IP Addr: _
DNS Serv IP Addr: _

26. Repeat for zone 7 if required
Programming Mode
Enable Zn 6 (Y/N)
(N)
Zn 6 Trigger Type
(V+)
Invert Zn 6 (Y/N)
(N)
V V to 13V Trips Zone
V V Ground Trips Zone
EOLR Loss of 2k EOLR Trips
No - Normal Zone Activation
Yes - Faulted Zone sends normal report.
- Normal Zone sends alarm report.
Restore Zn 6 Y/N
(Y)
Delay Zn 6 (secs)
(00)
ECP mode supports 2 optional hardwire zone input triggers on the zone 6 and zone 7 terminals.
When connected and programmed, the optional hardwire zones report in ADEMCO High-Speed format.
Enable zone turns on alarm reporting for the zone.
Trigger type selects the triggering method for this zone, positive, negative or end of line resistor.
Invert, inverts the alarm and normal states of the zone input trigger.
Restore, enables restore reporting for the zone.
Delay, defines the reporting delay in seconds for the zone, 01 to 15 or leave at 00 for no delay.
At this point in programming the same 5 locations covered here will be repeated for zone 7 trigger input.
Yes - Zone sends Restore report.
No - Zone will not send Restore report.
Zone can be Delayed from 1 to 15 seconds
Zone must remain faulted for the full extent of delay to send report.
Repeat for zone 7 if required

27. Programming Mode Pwr Save Mode (Y/N) (Y) _
When Power Save Mode is enabled, the Network Interface Card (NIC) powers up, Pings a Redir, and turn back off.
This process takes about 3 seconds and the process repeats every 20 seconds.
Some Routers may see this as being “under attack” and shut down the Port on the router.
Devices connected to routers that shut down the port may try using Static IP Addressing, before disabling the Power Save Mode feature. Power cycle the Router to reset the port, and determine if this was the problem.
NOTE: If this feature is disabled, the device will not meet the UL Requirement for Battery Backup. It will reduce the backup time to 18 hours.
The Use DHCP option will only be displayed on the 7845i_GSM,
DHCP Dynamically allocates the IP address, this is the recommended option.
If you can use DHCP then press enter to skip to Review.
If you can not use DHCP on the network, then enter no and obtain the following information from your IT administrator.
NIC IP address, Subnet Mask, Gateway IP address and the DNS Server IP address.
Key in the numbers obtained, To enter the dot you will press the star key.
After programming all 4 locations Review will be displayed.
By selecting yes to review allows you to verify all programming locations.

28. Press Shift Y then Enter to Continue and Exit
Programming Mode
Review? Y/N
Press Enter to Continue and Exit
Create Password?
Y/N
Press Enter to Continue and Exit
Exit Prog Mode?
Y/N
The Use DHCP option will only be displayed on the 7845i_GSM,
DHCP Dynamically allocates the IP address, this is the recommended option.
If you can use DHCP then press enter to skip to Review.
If you can not use DHCP on the network, then enter no and obtain the following information from your IT administrator.
NIC IP address, Subnet Mask, Gateway IP address and the DNS Server IP address.
Key in the numbers obtained, To enter the dot you will press the star key.
After programming all 4 locations Review will be displayed.
By selecting yes to review allows you to verify all programming locations.
Press Shift Y then Enter to Continue and Exit
Updating Root
File \
DONE
Resetting………

29. Zone Mode Setup

30. Programming Zone Mode With a LynxR/R-EN Panel, enable Lynx Panic
Lynx Panic Y/N
(N)
With a LynxR/R-EN Panel, enable Lynx Panic
Temporal Pulse = Zone 1 Report
FIRE
Constant or Steady = Zone 2 Report
BURG
Single 3 second Pulse = Zone 3 Report
Silent Panic, Medical, Duress
Always program Zone 1/2 as a negative trip (V-) and install a 2k EOLR across the zone input and ground.
ECP mode supports 2 optional hardwire zone input triggers on the zone 6 and zone 7 terminals.
When connected and programmed, the optional hardwire zones report in ADEMCO High-Speed format.
Enable zone turns on alarm reporting for the zone.
Trigger type selects the triggering method for this zone, positive, negative or end of line resistor.
Invert, inverts the alarm and normal states of the zone input trigger.
Restore, enables restore reporting for the zone.
Delay, defines the reporting delay in seconds for the zone, 01 to 15 or leave at 00 for no delay.
At this point in programming the same 5 locations covered here will be repeated for zone 7 trigger input.

31. This field also affects the zone 3 input.
Programming Zone Mode
Trip Inputs 1 or 2
w/Bell Out (N)
Enabling this option will change the required trip voltage on zones 1, 2 and 3, as described below.
Positive Trip – Always enable for Positive Trip.
Disabled – 2V
Enabled – 5V
Negative Trip
Disabled – 0V ground potential
Enabled – 0V to 5V will trip. Must be greater than 5V to be normal.
This field also affects the zone 3 input.
ECP mode supports 2 optional hardwire zone input triggers on the zone 6 and zone 7 terminals.
When connected and programmed, the optional hardwire zones report in ADEMCO High-Speed format.
Enable zone turns on alarm reporting for the zone.
Trigger type selects the triggering method for this zone, positive, negative or end of line resistor.
Invert, inverts the alarm and normal states of the zone input trigger.
Restore, enables restore reporting for the zone.
Delay, defines the reporting delay in seconds for the zone, 01 to 15 or leave at 00 for no delay.
At this point in programming the same 5 locations covered here will be repeated for zone 7 trigger input.

32. Programming Zone Mode
Telco Zone
(0)
Enabling this option will cause the specified zone input to send the High Speed Telco Report to Central Station.
Available for zones 3 through 7.
Telco Fault
Telco Restore
ECP mode supports 2 optional hardwire zone input triggers on the zone 6 and zone 7 terminals.
When connected and programmed, the optional hardwire zones report in ADEMCO High-Speed format.
Enable zone turns on alarm reporting for the zone.
Trigger type selects the triggering method for this zone, positive, negative or end of line resistor.
Invert, inverts the alarm and normal states of the zone input trigger.
Restore, enables restore reporting for the zone.
Delay, defines the reporting delay in seconds for the zone, 01 to 15 or leave at 00 for no delay.
At this point in programming the same 5 locations covered here will be repeated for zone 7 trigger input.

33. Example uses zone 3 to indicate Open/Close
Programming Zone Mode
Open/Close Zone
(0)
Enabling this option will cause the specified zone to send a High Speed Open or Close report to central station, in the zone that was indicated.
Example uses zone 3 to indicate Open/Close
Available for zones 3 through 7.
Arming – Restore Report
Disarming – Alarm Report
Note: If your trigger activates for Arming, you will need to enable INVERT for the zone. (Invert option will be discussed later.)
ECP mode supports 2 optional hardwire zone input triggers on the zone 6 and zone 7 terminals.
When connected and programmed, the optional hardwire zones report in ADEMCO High-Speed format.
Enable zone turns on alarm reporting for the zone.
Trigger type selects the triggering method for this zone, positive, negative or end of line resistor.
Invert, inverts the alarm and normal states of the zone input trigger.
Restore, enables restore reporting for the zone.
Delay, defines the reporting delay in seconds for the zone, 01 to 15 or leave at 00 for no delay.
At this point in programming the same 5 locations covered here will be repeated for zone 7 trigger input.

34. Programming Zone Mode
Multi-mode
(N)
Enabling this option will cause the specified zone ONLY attempt to generate an message via Total Connect Remote Services.
When enabled, only device Supervisory Messages will be sent to Central Station, i.e. Low Batt, AC Loss, Swinger Suppression, etc. (Not Tamper)
NOTE: This option should only be enabled when using Remote Services and Alarm Reports are not desired to be received by Central Station.
ECP mode supports 2 optional hardwire zone input triggers on the zone 6 and zone 7 terminals.
When connected and programmed, the optional hardwire zones report in ADEMCO High-Speed format.
Enable zone turns on alarm reporting for the zone.
Trigger type selects the triggering method for this zone, positive, negative or end of line resistor.
Invert, inverts the alarm and normal states of the zone input trigger.
Restore, enables restore reporting for the zone.
Delay, defines the reporting delay in seconds for the zone, 01 to 15 or leave at 00 for no delay.
At this point in programming the same 5 locations covered here will be repeated for zone 7 trigger input.

35. Programming Zone Mode Zn x Trigger Type (V+) Invert Zn x (Y/N) (N)
V V to 13V Trips Zone
V V Ground Trips Zone
EOLR Loss of 2k EOLR Trips
No - Normal Zone Activation
Yes - Faulted Zone sends normal report.
- Normal Zone sends alarm report.
ECP mode supports 2 optional hardwire zone input triggers on the zone 6 and zone 7 terminals.
When connected and programmed, the optional hardwire zones report in ADEMCO High-Speed format.
Enable zone turns on alarm reporting for the zone.
Trigger type selects the triggering method for this zone, positive, negative or end of line resistor.
Invert, inverts the alarm and normal states of the zone input trigger.
Restore, enables restore reporting for the zone.
Delay, defines the reporting delay in seconds for the zone, 01 to 15 or leave at 00 for no delay.
At this point in programming the same 5 locations covered here will be repeated for zone 7 trigger input.
Restore Zn x Y/N
(Y)
Delay Zn x (secs)
(00)
Yes - Zone sends Restore report.
No - Zone will not send Restore report.
Zone can be Delayed from 1 to 15 seconds
Zone must remain faulted for the full extent of delay to send report.

36. Exiting Program Mode Correctly
NEVER disconnect the programmer while in program mode.
ALWAYS exit program mode AND leave the programmer connected until the screen displays “DONE”.
If you didn’t exit correctly…
Plug the programmer back in and…
Press enter then exit as normal.
- or -
Power cycle the 7845GSM radio.

37. Registering…
Shift
Registering…
Registration
Successful

38. Registering…PIN Replacement
When registering the GSM radio press
Enter PIN
Wait for acknowledgement
PIN: _
Registering…
Registration
SUCCESS

39. Status Codes
The 7847i sends status messages to the control panel for tamper and network communication failures. When using Honeywell’s VISTA-10P, VISTA-15P, Vista 20P series control panels, the status is displayed on the control panel’s keypad as “Check 103 LRR” followed by a 4-digit code).
STATUS CODE
DESCRIPTION
0000
Control Panel lost communication with panel
0880
7847i tamper detected (cover removed)
0005
7847i has lost contact with AlarmNet
000F
7847i is not registered; radio account not activated
0400
7847i Power On Reset
0C80
7847i Power On Reset & Tamper detected
0C8F
7847i Power On Reset, Tamper detected & Not Registered

40. Status Display LEDs

41. Press and hold the Mode & Status button to view.
Mode & Status LEDs
Press and hold the Mode & Status button to view.
The two Yellow LEDs indicate which mode the device is programmed in.
The first Green LED indicates the status of the Internet or Web connection.

42. Network Connectivity LEDs

43. Central Station Messages

44. 7720P Programmer Diagnostic Commands

45. Programmer Keyboard Commands
The 7720P Programmer is an invaluable tool for troubleshooting the device and network connection. Section 5 of the Installation Instructions provides details of each command.
[ A ]
INTERNAL IP/GSM
x.x.xx mm/dd/yy
Software Revision
[ B ]
MAC xxxxxxxxxxxx
MAC CRC yyyy
MAC Address
[ C ]
Mon 01 Jan 2001
05:48:39 am
GMT Time and Date

46. Programmer Keyboard Commands
For more information on Network Diagnostics, see Section 6 of the Installation Instructions.
Physical Link
Good
Network Diagnostics Display
[ D ]
[ * ] to go to NIC IP Address
NIC IP Address
xxx.xxx.xxx.xxx
If using DHCP, this information is assigned by the Gateway/Router. If not using DHCP, this information must match the information provided by the site Network Administrator.
[ * ] to go to Subnet Mask
Subnet Mask
xxx.xxx.xxx.xxx
[ * ] to go to Gateway IP Address
Gateway IP Addr
xxx.xxx.xxx.xxx
[ * ] to go to DNS Server IP

47. Programmer Keyboard Commands
Network Diagnostics Display Continued
If using DHCP, this information is assigned by the Gateway/Router. If not using DHCP, this information must match the information provided by the site Network Administrator If using DHCP Run Network Diagnostic Tests
DNS Serv IP
xxx.xxx.xxx.xxx
[ * ] to go to encryption test
Encryption Test
AES Passed!
[ * ] to go to DHCP Status
DHCP OK
[ F ]
Testing Gateway
Redir 1

48. Programmer Keyboard Commands
ECP 67 TmPB Flt
xx OK
Status Display for ECP Mode
[ * ] = next field, [BS] = previous field
TmPB Flt
x OK
Status Display for 4204 Emulation Mode
[ * ] = next field, [BS] = previous field
TmPB Flt
5555 xx OK
Status Display for Emulation Mode
[ * ] = next field, [BS] = previous field
TmPB Flt OK
Status Display for Zone Trigger Mode
[ * ] = next field, [BS] = previous field
Bat NLd: x.xxV
Bat Ld: x.xxV
Battery Voltage Status Display
[ * ] = next field, [BS] = previous field

49. Programmer Keyboard Commands
ECP 67 TmPB Flt
xx OK
Status Display for ECP Mode
[ * ] = next field, [BS] = previous field
TmPB Flt
x OK
Status Display for 4204 Emulation Mode
[ * ] = next field, [BS] = previous field
TmPB Flt
5555 xx OK
Status Display for Emulation Mode
[ * ] = next field, [BS] = previous field
TmPB Flt OK
Status Display for Zone Trigger Mode
[ * ] = next field, [BS] = previous field
Bat NLd: x.xxV
Bat Ld: x.xxV
Battery Voltage Status Display
[ * ] = next field, [BS] = previous field

50. Programmer Keyboard Commands
[ S ] Continued
Battery Charger OK
Battery Charger Status Display
[ * ] = next field, [BS] = previous field
Line Voltage
xx.xxV
Line Voltage Status Display
[ T ]
Test Msg Sent
Send Test Alarm
[ * ] = next field, [BS] = previous field
Reset CPU Y/N
[ X ]
Reset the 7847i
[ * ] = next field, [BS] = previous field

51. Programmer Keyboard Commands
[ 0 ]
Force Server Update?
Y/N
Force Upload of Configuration File
Note: If the Internet is not available or if the module cannot communicate with AlarmNet, the following screen will be displayed after entering this command.
Cannot Upload
Try Later!_
Path for Data Transmission Not Available.

52.
and click on MyWebTech
User name: honeywell
Password: support99
Honeywell Security support
AlarmNet Support (800)