1. Goodson Tools and Supplies for Engine Builders
Keeper-Eeze Tools

2. Keeper- Eeze Tools KE-6802 KE-6940 KE-6902 KE-6901 KE-6804 KE-6903
Toll Free: Phone: : Web site:

3. Keeper-Eeze Demonstrated
on Honda CRF-250R
Toll Free: Phone: : Web site:

4. Valve Support Selection: A Shot-Bag or Chamber Plug must be used to hold up the valves while removing the valve locks.
The Shot-Bags will conform to the combustion chamber. They should not protrude too far from the deck surface when installed. Choose from the different size bags for the correct fit. Multiple bags can be used for large chambers.
Toll Free: Phone: : Web site:

5. Sleeve Selection
Determine the correct protective guide Sleeve. Pick the Sleeve that fits closest to the bucket bore dia. And the spring/ retainer assembly. Some engines require the valve spring clearance relief to be used as a guide.
ID always
fits tool
Toll Free: Phone: : Web site:

6. Installing Sleeve Fits in around spring & retainer
Install the correct size sleeve over the spring & retainer assembly. The sleeve will maintain the proper fit for removal and assembly of the spring & retainer.
Toll Free: Phone: : Web site:

7. This shows the proper sleeve installed around the spring and retainer.
Toll Free: Phone: : Web site:

8. T-Handle Assembly
Hold the T-handle portion of the Keeper-Eeze tool with the tube down between the fingers. Remove any Loader Modules from the tool by gently pulling on the plunger at the end to overcome the magnetic force. Retract the Adjuster by loosening the knob on the side and pulling it back.
Toll Free: Phone: : Web site:

9. Insert the Remover attachment (Order No
Insert the Remover attachment (Order No. KE-6803) into the end of the Keeper-Eeze tool. Push it in with a twisting action until it is fully seated.
Toll Free: Phone: : Web site:

10. Push tool down
Insert “T” Handle in sleeve installed in step 3. Hold tool down with one hand and firmly strike the T-Handle with palm of the opposite hand. This will release keepers. (Do not strike Keeper-Eeze with a hammer)
Toll Free: Phone: : Web site:

11. Lock and retainer held by remover
Pull the tool away from the cylinder head. The valve locks and retainer will be held safe by the Remover. Store the components for later assembly.
Toll Free: Phone: : Web site:

12. Remove valve lock & Retainer off of the magnet with your hand
Remove Spring
Toll Free: Phone: : Web site:

13. Remove valve
Toll Free: Phone: : Web site:

14. To Reassemble Install retainer on top of valve spring
Install valve spring
Toll Free: Phone: : Web site:

15. Spring Assembly in place Install Sleeve
Toll Free: Phone: : Web site:

16. Insert the installation attachment into the T-handle
Now the installation attachment is ready to have the correct keeper loader installed into the end of the installation attachment
Toll Free: Phone: : Web site:

17. Assembly
Insert the correct size loader module with the correct loader that matches the valve stem diameter until it seats up against the magnet
Toll Free: Phone: : Web site:

18. Fully Assembled
Loosen adjustment knob on side of T-handle. Then adjust loader module pin to approximately the same depth the keepers are located down on the valve stem.
Toll Free: Phone: : Web site:

19. Keepers are in position to be installed in the retainer and valve stem
Place the valve locks (keepers) on the Loader Plunger
Toll Free: Phone: : Web site:

20. Now insert into the top of the sleeve and push into the retainer
Same as removal, push down on T-handle Until an audible “click” is heard and felt in the handle and snaps in place and then remove T-handle
Now insert into the top of the sleeve and push into the retainer
Toll Free: Phone: : Web site:

21. Remove outer sleeve and you have a finished product
Toll Free: Phone: : Web site:

22. Keeper- Eeze Tools KE-6802 KE-6940 KE-6902 KE-6901 KE-6804 KE-6903
Toll Free: Phone: : Web site:

23. Goodson Tools and Supplies for Engine Builders
Keeper-Eeze Tools
Any questions on the Keeper- Eeze please contact us
Toll Free:
Phone:
Website: