1. （ 1 ） PROCEDURE FOR FLAT HEAT PRESS OPERATION PROCEDURE FOR MULTI FUNCTION HEAT PRESS MACHINE

2. ① Put the machine on a flat surface

3. ② Connect power

4. ③ Push down Red button and turn on the machine

5. ④ After three seconds, machine display as below picture.

6. ⑤ Press “SET”, upper line shows the machine real temperature, the lower line shows the set –up temperature.

7. ⑥ Press “SET”, there are two lines displayed: upper line shows 5P, lower line shows set-up temperature.

8. ⑦ Press to set the temperature needed.

9. ⑧ Press “SET” again, upper line shows 5F,lower lines shows original set time.

10. ⑦ Press to set the time needed.

11. ⑩ Then press “SET” again, upper line shows machine real temperature, lower line shows set temperature.

12. 11 、 When upper line temperature shows the same with the lower line set-up temperature.

13. 12 、 Put the material on the machine

14. 13 、 Put the heat transfer paper on the material

15. 14 、 Press down the upper plate, and then press “Green button”

16. 15 、 When the time shows “0”, means the heat transfer process finished.

17. （ 2 ） PROCEUDER FOR CUP HEAT PRESS OPERATION PROCEDURE FOR MULTI FUNCTION HEAT PRESS MACHINE

18. ① Put the machine on a flat surface

19. ② Change the relative power wire.

20. ③ Press “Red button” to turn on the machine

21. ④ Three seconds later, screen display as below:

22. ⑤ Press “SET”, upper line shows the machine real temperature, the lower line shows the set –up temperature.

23. ⑥ Press “SET”, there are two lines displayed: upper line shows 5P, lower line shows set-up temperature.

24. ⑦ Press to set the temperature needed.

25. ⑧ Press “SET” again, upper line shows 5F,lower lines shows original set time.

26. ⑦ Press to set the time needed.

27. ⑩ Then press “SET” again, upper line shows machine real temperature, lower line shows set-up temperature.

28. 11 、 When upper line temperature shows the same with the lower line set-up temperature.

29. Remark How to change the cup heating platen?

30. ① Loose the screw on the cup platen as below:

31. ② Change other size heating platen and fasten screws.

32. ③ Connect the wire.

33. (3) PROCEDURE FOR PLATE HEAT PRESS OPERATION PROCEDURE FOR MULTI FUNCTION HEAT PRESS MACHINE

34. ① Put the machine on a flat surface

35. ② Loose the screws on the upper heating plate, see below picture Screws should be loosen.

36. ③ Picture for all screws are loosen.

37. ④ Take away the upper heating plate.

38. ⑤ Prepare the heating part for plate.

39. ⑥ Install the heating part according to below picture and fasten the screws.

40. ⑦ Picture after heating part installation:

41. ⑧ Connect the power

42. ⑨ Push down Red Button and turn on machine

43. ⑩ After three seconds, machine display as below picture.

44. 11 、 Press “SET”, upper line shows the machine real temperature, the lower line shows the set –up temperature.

45. 12 、 Press “SET”, upper line shows 5P, lower line shows set-up temperature.

46. 13 、 Press to set the temperature needed.

47. 14 、 Press “SET” again, upper line shows 5F,lower lines shows original set time.

48. 15 、 Press to set the time needed.

49. 16 、 Then press “SET” again, upper line shows machine real temperature, lower line shows set temperature.

50. 17 、 When upper line temperature shows the same with the lower line set-up temperature, then you can process plate heat transfer.

51. （ 4 ） PROCEDURE FOR HAT HEAT PRESS OPERATION PROCEDURE FOR MULTI FUNCTION HEAT PRESS MACHINE

52. ① Put the machine on a flat surface

53. ② Loose the screws on the upper heating plate, see below picture Screws should be loosen.

54. ③ Picture for all screws are loosen.

55. ④ Take away the upper heating plate.

56. ⑦ Loose the two screws under the lower heating plate. Loose these two screws.

57. ⑧ Picture after two screws loosen out

58. ⑨ Move away the lower heating platen

59. ⑩ Picture after heating platens are moving away.

60. 11 、 Picture after heating platens are moving away.

61. 12 、 Loose the two screws in the middle The two screws

62. 12 、 Picture after two screws loosen.

63. 13 、 Fasten the lower heat platen.

64. 14 、 Fasten the screws in the front

65. 15 、 Fasten the screws in back side.

66. 13 、 Lower hat heat platen installation is finished.

67. 14 、 Fasten the screws to fix the upper hat heat platen.

68. 15 、 Picture after both platens fixed.

69. 16 、 Connect power wire.

70. 17 、 Now, installation finish

71. 18 、 Press Red Button to turn on machine.

72. 19 、 After three seconds, machine display as below picture.

73. 20 、 Press “SET”, upper line shows the machine real temperature, the lower line shows the set –up temperature.

74. 21 、 Press “SET”, upper line shows 5P, lower line shows set-up temperature.

75. 22 、 Press to set the temperature needed.

76. 23 、 Press “SET” again, upper line shows 5F,lower lines shows original set time.

77. 24 、 Press to set the time needed.

78. 25 、 Then press “SET” again, upper line shows machine real temperature, lower line shows set temperature.

79. 26 、 When upper line temperature shows the same with the lower line set-up temperature, then you can process hat heat press.