1. AAQMS – DAS Requirements
A Data Acquisition System utilized in air quality and/or emissions monitoring should do far more than simply collect data.
It should provide a means for remotely checking the system and each individual analyzer.
It should enable analyzers and calibration system to be configured remotely.
It should reliably log data directly from the instruments in digital form.
It should automatically warn the user of measurement exceedances or events such as calibration failures.
It should be easy to use.

2. Teledyne – Win AQMS DAS
WinAQMS is a Windows® based system which provides full control over the entire system (remote and onsite) enabling automatic calibrations to be performed and system errors to be monitored.
WinAQMS interfaces to analyzers via a RS232 multi-drop serial link, through a USB link or via TCP/IP network link. This allows it to collect data directly from the instruments in digital format thus eliminating digital to analog and analog to digital conversion errors. The bi-directional interface also allows a remote central computer, running Teledyne WinCollect software, to access full control and diagnostics of the analyzers used and data to be collected remotely.
The Data Acquisition system has sufficient data storage to hold well over thirty years worth of historical data.

3. Main Features : Win AQMS (DAS)
Supports remote communication from anywhere in the world enabling full control over the pollution monitoring system and direct interfacing with supported analyzers
Full control over calibration cycle periods
Remote communication through dial-up, Ethernet, satellite telephone networks, 3G network as well as short haul modems
Solid state hard disk drive eliminates risk of mechanical failure due to shock, high temperatures, vibration and harsh environments.
Data retrieval via USB Memory Stick or Mini SD card in the event communication networks are unavailable
"Industry Standard" RS232 and USB Communication enables digital communication with a wide range of supported monitoring equipment
Captures minimum, maximum, average values and standard deviations
Creates calculated channels that allows the user to apply calculations to data (logged automatically)
Fifth Generation Data Acquisition & Control System based on 30 years of field experience
Data storage space for over thirty years of 5 minute historical data
Lightning & surge protection facilities
Windows XP PRO Compatible

4. Specifications : Win AQMS (DAS)
CPU: Ghz+
RAM: 1 Gbytes
Hard Drive Config.: Solid State 64 Gbytes Display Driver: Supporting up to 1929 x 1200 (allows dual screen)
Operating System: Windows XP Data Storage Format: Data Stored in Ascii format
Data Averaging Periods: Up to 4 independent data sets Selectable between 1 minute and 7 days
Calibration control: Automatic Span and Zero control. Calibration data is stored separately
Communication ports: 1 RS232 /RS485 serial ports standard, 6 x USB2.0 Ports
Networking :1000 Base T Ethernet g WLAN
Power: 12 volts < 7 Watt power supply.
Size: 10.1 x 11.5 x 2.7 cm  370 grams

5. AAQMS with DAS

6. AAQMS – Sample Conditioning System

7. AAQMS Analyzer Panel

8. Mobile AAQMS Station

9. AAQMS Mobile Shelter

10. AAQMS Cabinet – Rear & Front Side

11. AQMS Calibration Procedure

12. AQMS Calibration Procedure

13. AQMS Calibration Procedure
1] SO2 CALIBRATION: 6400E (Refer manual for reference)
The following three-step procedure assumes that the instrument does not have any of the available zero/span (Z/S) or IZS valve options installed. Chapter 7 contains instructions for calibrating instruments with valve options. Chapter 8 contains directions for performing for EPA protocol calibrations.
The initial calibration should be carried out with the analyzer’s reporting range for SINGLE range mode with a range span of 500 PPB (factory default settings for most units). This will enable you to compare your results to the factory calibration.
STEP ONE: Set/verify the analog output reporting range of the M100E:

14. AQMS Calibration Procedure

15. AQMS Calibration Procedure
STEP TWO: Set the expected SO2 span gas concentration.

16. AQMS Calibration Procedure
STEP THREE: Perform the zero/span calibration procedure:

17. AQMS Calibration Procedure
Check the value of the SLOPE and OFFSET test functions (see Section 6.2.1) to verify that they are within the limits listed in Table 7-5)
Model 100E analyzer is now ready for operation.

18. AQMS Calibration Procedure
2] NOX CALIBRATION: 9110E (Refer manual for reference)
The initial calibration should be carried out using the 500ppb range, a span gas with about 400 ppb NO and with the unit set for SINGLE range, which will enable you to compare your calibration results to the factory calibration as listed on the Final Test and Validation Data sheet. The following three-step procedure assumes that the instrument does not have any of the available zero/span (Z/S) valve options installed. Chapter 1 contains instructions for calibrating instruments with Z/S valve options, Chapter 1 for EPA protocol calibration.
STEP ONE: Set the analog output range of the M200E:

19. AQMS Calibration Procedure

20. AQMS Calibration Procedure
STEP TWO: Set the expected NO and NOX span gas concentration. If you supply NO gas to the analyzer, the values for expected NO and NO2 need to be identical.

21. AQMS Calibration Procedure
Perform the zero/span calibration procedure:

22. AQMS Calibration Procedure

23. AQMS Calibration Procedure
The Model 200E analyzer is now ready for operation.
3] CO CALIBRATION: 7001E (Refer manual for reference)
Set the expected CO span gas concentration

24. AQMS Calibration Procedure
Perform the Zero/Span Calibration Procedure
The Model GFC7001E Analyzer is now ready for operation.

25. AQMS Calibration Procedure
4] O3 CALIBRATION: 7001E (Refer manual for reference)
The O3 span concentration value automatically to PPB and it is recommended that an O3 calibration gas of that concentration be used for the initial calibration of the unit. To verify that the analyzer span setting is set for 400 PPB

26. AQMS Calibration Procedure
To perform an initial Calibration of the Model 400E photometric ozone analyzer, press

27. AQMS Calibration Procedure

28. AQMS Calibration Procedure
The Model 400E ANALYZER IS NOW READY FOR OPERATION.
5] VOC CALIBRATION: 4060 (Refer manual for reference)
The analysis has 2 modes: Sample Mode and Analysis Mode.
1) Sample Mode:
In this mode, the Analyzer configures the operational valve to back flush the column and charge the sample loop. The sample mode is programmed to continue for a 7 minute period by factory default; however, it is usually modified to match the needs of a particular process. It is possible to set the Sample Mode duration up to 30 minutes.

29. AQMS Calibration Procedure
2) Analysis Mode
During this mode, the Analyzer configures the operational valve to feed the gas in the sample loop through the column to the detector. If configured to do so, the Analyzer may read the detector for a 5 second period programmed somewhere during this mode to obtain a baseline reading for further calculation. This mode is usually programmed to continue until the compound of interest is fully calculated from the column. It is possible to set it up to 10 minutes.
During the Analysis Mode, a ‘Peak Detect’ period is programmed at which time the Analyzer reads the Detector Output. The Analyzer stores the maximum reading during this time and uses the value in conjunction with the baseline value to calculate the concentration of the compound of interest. The calculation is performed at the end of the ‘Peak Detector’ period and the result is displayed at the end of Analysis Mode.

30. AQMS Calibration Procedure

31. AQMS Calibration Procedure

32. AQMS Calibration Procedure

33. SO2 Analyzer – Model 6400E Maintenance Schedule
Item
Action
Priority
Frequency
Cal Check
Particulate filter
Change particle filter
Mandatory
Weekly or As Needed No
Flow controller
Replace sintered filter & O-rings
Annually
Yes
Pump
Rebuild-Kit
Zero/span calibration
As Needed
Annually or as needed
Sample Chamber windows and Filters
Clean
As necessary
TEST functions
Review and evaluate
Recommended
Weekly
Pneumatic sub-system
Check for leaks in gas flow paths
Annually or after repairs involving pneumatics
Yes on leaks, else no
PMT Sensor Hardware Calibration
Low-level hardware calibration
On PMT or preamp changes

34. NO x Analyzer - 9110 Maintenance Schedule

35. CO Analyzer – GFC 7001E Maintenance Schedule

36. O3 Ozone Analyzer – Model 400E Maintenance Schedule

37. Zero Air Generator - Model 701 Maintenance
Before any maintenance cycle power on/off, drain any water in bowl
Do not loosen any tubing connection while the 701 is running.
Before working on the 701 plumbing turn off the 701, wait for the pressure gauge to read zero. (This may require that you loosen the rear panel bulkhead union to allow the air to bleed away.)
Even though the front panel power switch is off, there is line voltage present at the power entry terminals, power switch terminals and on the control board. For added safety, remove the power cord from the rear panel receptacle.
Occasionally, depending upon the local conditions, check the inside of the 701 for excessive dirt or dust.
Particularly, check the cooling fan, cooling coil and compressor fan inlet.
Remove any dirt or dust with a vacuum cleaner. Do not use an air jet. This will only redistribute the dirt and will not remove it.

38. VOC Analyzer – Model 4060 GC Routine Maintenance
The pressure gauges and flow rate should be checked weekly.
All support gases need to be replaced when the primary gauge reaches 100PSIG.
Span calibration required whenever Air/Fuel cylinder is replaced or flame is re-ignited.

39. VOC Analyzer – Model 4060 GC Routine Maintenance
Item
Action
Frequency
Remarks
Front Panel Pressure Gauge Setting
Air
Set pressure as recommended
Daily/Weekly
Ensure that press setting is same as per previous calibration.
Fuel
Carrier
Very critical. Do not disturb on front gauge. Ensure that Cylinder outlet pressure is at 80 to 90psig.
Support Gases Cylinder press.
Replace cylinder when primary pressure reaches 100psig.
As on required
Whenever cylinder replaced, perform span calibration.

40. VOC Analyzer – Model 4060 GC Routine Maintenance
Item
Action
Frequency
Remarks
Front Panel Pressure Gauge Setting
Air
Set pressure as recommended
Daily / Weekly
Ensure that press setting is same as per previous calibration.
Calibration Gas Cylinders
Span
Calibration
Weekly
Whenever cylinder replaced, perform calibration.
Sample
Bypass flow
Sample / Zero / Span
Set as recommended
Ensure that flow setting is same as per previous calibration.
Temp.
FID / GC/Sample
Check PV/SV values. All temp. should maintained as per SV.
Ensure that GC Temperature is as per PV value.

41. Zero Air Generator - Model 701 Maintenance Schedule

42. MFC – Model 700E Maintenance Schedule

43. TELEYNE Team Thank you All
Company Confidential
TELEYNE Team Thank you All
Company Headquarters: City of Industry, California USA
Facility: 60,000 sq. ft. / ISO-9001:2008
Founded: 1945
Core Capabilities: Manufacturer of high quality measurement and control instrumentation.
Website: