1. Menu Copyright © 2005 by The SEA Group negative pressure respirators

2. Menu Copyright © 2005 by The SEA Group Menu Jump to… Next slide Filters/cartridges Half masks — features Half masks — fitting Half masks — maintenance Half masks — communication Full face masks — features Full face masks —maintenance Full face masks — communication

3. Menu Copyright © 2005 by The SEA Group The Sundström half mask system Gas filter(s) Particle filter Pre-filter Pre-filter holder Leakage test disk Mask body Inhalation valve Exhalation valve Valve cap Head harness

4. Menu Copyright © 2005 by The SEA Group FILTERS 1: Particle Filters Skip to Half Masks

5. Menu Copyright © 2005 by The SEA Group Two main types Mechanical impact (such as Sundström) A fine mesh barrier that lets air through but not particles Electrostatic Electric charged filter material acts like a “glue”, making particles stick to filter surface

6. Menu Copyright © 2005 by The SEA Group The 1 st problem with ELECTROSTATIC: It’s like throwing tacks at a magnet: Throw them SLOWLY, and the magnet catches them all

7. Menu Copyright © 2005 by The SEA Group …but throw them QUICKLY, and some will get through The 1 st problem with ELECTROSTATIC:

8. Menu Copyright © 2005 by The SEA Group The 1 st problem with ELECTROSTATIC: REDUCTION in some filters up to

9. Menu Copyright © 2005 by The SEA Group So how can electrostatic filters pass standards tests?

10. Menu Copyright © 2005 by The SEA Group So how can electrostatic filters pass standards tests? Because standards tests are done at 95 litres/minute… …while people often breathe at 300-500 litres/minute!

11. Menu Copyright © 2005 by The SEA Group The 2 nd problem with ELECTROSTATIC: Moisture | Humidity | Oil mist

12. Menu Copyright © 2005 by The SEA Group The 2 nd problem with ELECTROSTATIC: Oil mist is EVERYWHERE!

13. Menu Copyright © 2005 by The SEA Group Mechanical Impact Not affected by air speed Not significantly affected by humidity or oil mist Only keeps on collecting particles Gets “better” the more particles are caught Replace when hard to breathe through

14. Menu Copyright © 2005 by The SEA Group Sundström particle filter P100 Dry particles (dust) Wet particles (aerosols, sprays) Smoke and fumes Fibres Mould Bacteria and viruses

15. Menu Copyright © 2005 by The SEA Group When to replace If there is any damage to the filter or When the filter feels hard to breathe through or After 4-6 weeks’ use

16. Menu Copyright © 2005 by The SEA Group Comparison Other brands: Every week* Sundström: Every 4-6 weeks Particle filter replacement *) Average filter life 40 hours, as stated by manufacturer

17. Menu Copyright © 2005 by The SEA Group FILTERS 2: Gas Filters

18. Menu Copyright © 2005 by The SEA Group Adsorption efficiency of gas filtres NOT affected by air flow rate

19. Menu Copyright © 2005 by The SEA Group Pulsating air flow MAY affect life span (still 100% adsorption, but time before breakthrough may be shortened)

20. Menu Copyright © 2005 by The SEA Group Colour coding Organic vapour AmmoniaAcid gas - Inorganic Gas Particles

21. Menu Copyright © 2005 by The SEA Group Combination filters If you need protection against BOTH particles and gas: A: Use a special combination filter B: Make a combination filter by pressing a particle filter onto the front of a gas filter

22. Menu Copyright © 2005 by The SEA Group To separate a combination filter Insert a coin or similar between the rim of the particle filter and the lug on the side of the gas filter Twist apart

23. Menu Copyright © 2005 by The SEA Group When to replace According to a replacement schedule Replacement of gas filters depends on: Type of contaminant Concentration of contaminant Temperature and Humidity Workload

24. Menu Copyright © 2005 by The SEA Group FILTERS: 3: Pre-filters

25. Menu Copyright © 2005 by The SEA Group Pre-filters… Should ALWAYS be used Protect the main filter Are low cost items Should be replaced AT LEAST once a day

26. Menu Copyright © 2005 by The SEA Group Sundström half mask SR100 Skip to Fitting

27. Menu Copyright © 2005 by The SEA Group Features Mask body and filter holder are made of a SINGLE PIECE of silicone material

28. Menu Copyright © 2005 by The SEA Group Features Large surface area of the filter holder means a lighter filter and lower breathing resistance

29. Menu Copyright © 2005 by The SEA Group Features Filter holder situated very low on the mask. This means much better weight balance on the face

30. Menu Copyright © 2005 by The SEA Group Features Continuous one-piece head harness works like shock absorbers on a car: weight and tension are evenly distributed

31. Menu Copyright © 2005 by The SEA Group Features Head harness is easily removed for cleaning or replacement

32. Menu Copyright © 2005 by The SEA Group Features Specially designed valve cups with internal deflectors to eliminate clogging of the valve by spray or aerosols

33. Menu Copyright © 2005 by The SEA Group Features Exhalation valves have a 90 degree flange to stabilize movement and ensure rapid return to closed position

34. Menu Copyright © 2005 by The SEA Group Features Sealing surfaces (rims) are sandblasted (matted) for slip-free seal. A deep chin cup ensures secure fit and good balance

35. Menu Copyright © 2005 by The SEA Group Features The mask if fitted with a water-proof bar-coded name tag for easy identification and tracking

36. Menu Copyright © 2005 by The SEA Group Features The special test adapter can be used on the wearer’s own mask without leaving any marks

37. Menu Copyright © 2005 by The SEA Group Sundström SR100 Not designed to suit the standard —— Designed to suit

38. Menu Copyright © 2005 by The SEA Group Knowledge base A wealth of information and knowledge support is available on CD-ROM and Internet

39. Menu Copyright © 2005 by The SEA Group Training program Sundström respiratory protection is backed by a solid authorisation program

40. Menu Copyright © 2005 by The SEA Group How to fit Make sure the mask is: Intact Fully assembled Fitted with correct filters Clean Yours 1 Skip to Maintenance

41. Menu Copyright © 2005 by The SEA Group How to fit Sling neck strap around your neck Start by placing your chin in the chin cup Cup the mask up over your mouth and nose 2

42. Menu Copyright © 2005 by The SEA Group How to fit Pull the head strap over your head Head pad should rest on the crest of your head NEVER fit head harness over helmet, cap, ear muffs or other head gear 3

43. Menu Copyright © 2005 by The SEA Group How to fit Adjust the tension by using the buckle, if needed 4

44. Menu Copyright © 2005 by The SEA Group How to fit Pull a few times on the BOTTOM strap. This will create more tension in the upper strap, resulting in greater lift and optimum balance 5

45. Menu Copyright © 2005 by The SEA Group Leakage test Perform a leakage test every time you will use the mask Place the leakage test disk instead of a pre-filter in the pre-filter holder Breathe in and hold your breath The mask collapses against your face. It should stay collapsed until you release your breath. If it returns quickly to normal shape, you have a leakage problem

46. Menu Copyright © 2005 by The SEA Group Annual fit test Individual fit testing using PortaCount or similar equipment should be performed at least once a year This will ensure that people whose facial features have changed (due to dentures, lost teeth, severe acne, facial scarring etc) are still receiving the protection they need

47. Menu Copyright © 2005 by The SEA Group Maintenance Skip to Communication

48. Menu Copyright © 2005 by The SEA Group Maintenance Remove filters Wipe the mask body inside and out with a clean damp cloth Pay special attention to sealing surfaces and filter holder 1

49. Menu Copyright © 2005 by The SEA Group Maintenance Remove the inhalation valve carefully Check and clean the valve Wipe the valve seat Replace the valve 2

50. Menu Copyright © 2005 by The SEA Group Maintenance Remove the exhalation valve caps Remove the exhalation valves carefully Check and clean the valves, the valve seats and valve caps Replace the valves and caps Perform a leakage test 3

51. Menu Copyright © 2005 by The SEA Group Maintenance Clean the head harness with a dry brush Remove the harness if necessary Check that the harness is taut and elastic, otherwise replace 4

52. Menu Copyright © 2005 by The SEA Group Communication Skip to Full Face Mask

53. Menu Copyright © 2005 by The SEA Group SmallTalk

54. Menu Copyright © 2005 by The SEA Group SmallTalk Talk while wearing mask Small size Snap-on fitting High amplification Clear sound Ideal for teamwork

55. Menu Copyright © 2005 by The SEA Group SmallTalk Microphone snaps on to exhalation valve just like a normal valve cap

56. Menu Copyright © 2005 by The SEA Group SmallTalk Standard 9V battery Long duration Easy to replace

57. Menu Copyright © 2005 by The SEA Group SmallTalk Wear speaker unit on waist belt

58. Menu Copyright © 2005 by The SEA Group SmallTalk Cable clip keeps lead away and prevents snagging and pulling

59. Menu Copyright © 2005 by The SEA Group Sundström full face mask SR200 Skip to Maintenance

60. Menu Copyright © 2005 by The SEA Group Features Made of soft, non-allergenic silicone Spherical visor means greater field of vision with less reflection. Face sits further forward in the mask for even better field of vision Uniquely designed, single- action head harness Twin exhalation membranes

61. Menu Copyright © 2005 by The SEA Group Features Visor available in polycarbonate or laminated glass 1/3 of inhaled air is channeled across the visor, keeping the visor mist-free Exceptionally low weight at 460g (1.0 lb) Head harness of fabric — no sticky rubber on the hair Bar-coded ID tag

62. Menu Copyright © 2005 by The SEA Group Features Specially designed valve cups with internal deflectors to eliminate clogging of the valve by spray or aerosols

63. Menu Copyright © 2005 by The SEA Group Features Exhalation valves have a 90 degree flange to stabilize movement and ensure rapid return to closed position

64. Menu Copyright © 2005 by The SEA Group Features The mask if fitted with a water-proof bar-coded name tag for easy identification and tracking

65. Menu Copyright © 2005 by The SEA Group Features The special test adapter can be used on the wearer’s own mask without leaving any marks

66. Menu Copyright © 2005 by The SEA Group Sundström SR200 Not designed to suit the standard —— Designed to suit

67. Menu Copyright © 2005 by The SEA Group Knowledge base A wealth of information and knowledge support is available on CD-ROM and Internet

68. Menu Copyright © 2005 by The SEA Group Training program Sundström respiratory protection is backed by a solid authorisation program

69. Menu Copyright © 2005 by The SEA Group How to fit Make sure the mask is: Intact Fully assembled Fitted with correct filters Clean Yours 1 Skip to Maintenance

70. Menu Copyright © 2005 by The SEA Group How to fit Sling the neck strap around your neck Loosen the head harness straps Lift the head harness away from the mask body 2

71. Menu Copyright © 2005 by The SEA Group How to fit First, place your chin in the chin cup Cup the mask up and over your face 3

72. Menu Copyright © 2005 by The SEA Group How to fit Pull the head harness all the way down to your neck 4

73. Menu Copyright © 2005 by The SEA Group How to fit Tighten the straps in pairs Start with the BOTTOM pair of straps 5

74. Menu Copyright © 2005 by The SEA Group How to fit Continue by tightening the MIDDLE pair of straps 6

75. Menu Copyright © 2005 by The SEA Group How to fit Make sure the mask fits securely. It should not be uncomfortably tight 7

76. Menu Copyright © 2005 by The SEA Group Maintenance Remove filters Wipe the mask body inside and out with a clean damp cloth Pay special attention to sealing surfaces and filter holder 1 Skip to Communication

77. Menu Copyright © 2005 by The SEA Group Maintenance Remove the inhalation valve carefully Check and clean the valve Wipe the valve seat Replace the valve 2

78. Menu Copyright © 2005 by The SEA Group Maintenance Remove the exhalation valve caps Remove the exhalation valves carefully Check and clean the valves, the valve seats and valve caps Replace the valves and caps Perform a leakage test 3

79. Menu Copyright © 2005 by The SEA Group Leakage test Perform a leakage test every time you will use the mask Place the leakage test disk instead of a pre-filter in the pre-filter holder Breathe in and hold your breath The mask collapses against your face. It should stay collapsed until you release your breath. If it returns quickly to normal shape, you have a leakage problem

80. Menu Copyright © 2005 by The SEA Group Annual fit test Individual fit testing using PortaCount or similar equipment should be performed at least once a year This will ensure that people whose facial features have changed (due to dentures, lost teeth, severe acne, facial scarring etc) are still receiving the protection they need

81. Menu Copyright © 2005 by The SEA Group Communication

82. Menu Copyright © 2005 by The SEA Group SmallTalk

83. Menu Copyright © 2005 by The SEA Group SmallTalk Talk while wearing mask Small size Snap-on fitting High amplification Clear sound Ideal for teamwork

84. Menu Copyright © 2005 by The SEA Group SmallTalk Microphone snaps on to exhalation valve just like a normal valve cap

85. Menu Copyright © 2005 by The SEA Group SmallTalk Standard 9V battery Long duration Easy to replace

86. Menu Copyright © 2005 by The SEA Group SmallTalk Wear speaker unit on waist belt

87. Menu Copyright © 2005 by The SEA Group SmallTalk Cable clip keeps lead away and prevents snagging and pulling

88. Menu Copyright © 2005 by The SEA Group