1. OPERATION OF THE LARUE TACTICAL R.A.T. STOCK TM-LT800 Before using this equipment, please be certain you have read, and understand this manual. Manufactured By: LaRue Tactical 850 County Road 177 Leander, Texas USA 78641 ISSUED: September 2012 ®

2. TM-LT800 OPERATIONAL MANUAL FOR LARUE TACTICAL R.A.T. STOCK Manufactured By: Austin Precision Products, Inc. (DBA LaRue Tactical) 850 County Road 177 Leander, Texas USA 78641 512-259-1585 (voice) 512-259-1588 (fax) www.LaRue.com SALES@LARUETACTICAL.COM Manufactured By: LaRue Tactical 850 County Road 177 Leander, Texas USA 78641 ISSUED: September 2012 Page 1 TM-LT800 OPERATIONAL MANUAL FOR LARUE TACTICAL R.A.T. STOCK ®

3. TABLE OF CONTENTS Title Page …………………………………………………….P 1 Table of Contents ……………………………………………P 2 Guidelines For Proper Use …………………………..……..P 3 CHAPTER 1 INTRODUCTION ……………………………..P 4 I.General II.Specifications …………………………………………P 4 CHAPTER 2 ASSEMBLY AND OPERATION ……….…….P 5 1.0 Inspection …..…………………………………P 5 2.0 Explanatory Diagrams ………………………..P 5 3.0 Installation & Basic Operation …………….…P 6 4.0 Using The Trigger Lock ….………………….P 7 5.0 Removing The Butt Plate …….………………P 8 6.0 Removing And Assembling The Rod Kit……P 9 7.0 Replacing The Butt Plate ……….……………P 10 8.0 Removal From Rifle …………………………..P11 Page 2 TM-LT800 OPERATIONAL MANUAL FOR LARUE TACTICAL R.A.T. STOCK

4. GUIDELINES FOR PROPER USE The LaRue R.A.T. Stock is designed to easily drop on to “Mil-Spec” 6- position receiver extensions (aka buffer tubes). The LaRue R.A.T. Stock will not work properly on “Commercial” extensions. Below, is a diagram that shows the principal differences between a commercial extension and a mil-spec extension. Page 3 TM-LT800 OPERATIONAL MANUAL FOR LARUE TACTICAL R.A.T. STOCK

5. CHAPTER 1 INTRODUCTION I.GENERAL The LaRue RAT™ Stock was designed to be the ideal complement to the LaRue Tactical AR15 family of rifles. The RAT works with any Mil-Spec Receiver Extension. The unique 2-stage trigger mechanism allows shooters to adjust the pull length of the stock while in a variety of shooting positions. The CNC-machined internals allow for smooth operation as trigger mechanism is pulled to the rear and released. The internals provide positive lockup on Mil-Spec receiver extension positions. The internal cavity is designed for a snug fit without the need for an additional locking mechanism. Ambidextrous 1/4” swivel sockets, and 1” slots provide ideal anchor points for two-point slings. A locking rear butt-plate slides open to expose compartments that hold cleaning kit components. II.SPECIFICATIONS Length: 6.990” Height: 5.30” Materials: Glass-filled polymer frame with metal internals. Over- molded rubber Butt Plate. Page 4 TM-LT800 OPERATIONAL MANUAL FOR LARUE TACTICAL R.A.T. STOCK

6. CHAPTER 2 ASSEMBLY AND OPERATION 1.0Inspection Unpack the target. Inventory the kit, in accordance with the components shown below. 2.0Explanatory Diagrams Page 5 TM-LT800 OPERATIONAL MANUAL FOR LARUE TACTICAL R.A.T. STOCK LOCKING SWITCH TR IGGER REAR VIEW SLING SLOT SLING SOCKET TR IGGER TAKEDOWN ACCESS PORT SIDE VIEWFRONT VIEW ROD KIT ROD SLEEVE (L) ROD SLEEVE (R) ROD HARDPOINT BUTT PLATE INTERIOR ROD SLEEVE ACCESS HOLES SLING SLOT SLING SOCKET LOCKING SWITCH BUTT PLATE TAKEDOWN ACCESS HOLE

7. 3.0 Installation & Basic Operation Make sure firearm is unloaded. Remove old stock, if necessary. 1. Grasp RAT Stock in hand as shown, pull back on trigger (all the way) and slide stock into position on receiver extension. Page 6 TM-LT800 OPERATIONAL MANUAL FOR LARUE TACTICAL R.A.T. STOCK 2. Pull back on trigger half-way and slide stock back and forth into desired position. Release to lock into place.

8. Page 7 TM-LT800 OPERATIONAL MANUAL FOR LARUE TACTICAL R.A.T. STOCK Even with the Locking Switch in the horzontal position, the stock can be moved along the length of the receiver extension by pulling the trigger half-way to the rear. 4.0 Using the Trigger Lock The Trigger Lock is designed to prevent to stock from being accidently removed from the extention. The RAT Stock ships with the Locking Switch rotated to the vertical position. This allows the user to install and remove the stock on the receiver extention. Once the stock is installed on the extension, the user may choose to rotate the switch to the horizontal postion. Vertical position UNLOCKS the stock Horizontal position LOCKS the stock

9. Page 8 TM-LT800 OPERATIONAL MANUAL FOR LARUE TACTICAL R.A.T. STOCK 5.0 Removing The Butt Plate The RAT Stock Butt Plate can easily be removed by depressing the spring loaded pin located in the takedown access port, and sliding if off of the stock. 1. Orientate Butt Plate as shown. 2. Grasp as shown. Start applying sliding-pressure towards the bottom of the stock. SLIDING PRESSURE 3. Depress spring-loaded pin with bullet tip, or similar object. 4. Slide Butt Plate off stock. TAKEDOWN ACCESS PORT

10. Page 9 TM-LT800 OPERATIONAL MANUAL FOR LARUE TACTICAL R.A.T. STOCK 6.0 Removing And Assembling The Rod Kit An emergency cleaning rod kit is available for field-expedient cleaning and for tapping stuch cartridges from chambers. 1. Push Rod Sleeves from the front, using a bullet tip or a similar tool. 2. Grasp Rod Sleeves, and pull them free from the stock. 4. Screw Main Rod into treaded Rod Hardpoint in Butt Plate. 5. Thread remaining Rods together. ROD KIT ROD SLEEVES ROD HARDPOINT 3. Drop Rods free from Rod Sleeves. REVERSE ORDER TO STORE BACK INSIDE STOCK.

11. Page 10 TM-LT800 OPERATIONAL MANUAL FOR LARUE TACTICAL R.A.T. STOCK 7.0 Replacing The Butt Plate The RAT Stock Butt Plate can easily be replaced by inserting the Retention Tab into the large opening at the top, aligning the plate and pushing it into position. 1. Orientate Butt Plate as shown. Insert Tab as shown. 2. Grasp as shown, push against spring-loaded pin. Start applying sliding-pressure towards the top of the stock. SLIDING PRESSURE 3. Slide Butt Pad in position, until you hear the spring-loaded pin “click”. RETENTION TAB PRESSURE

12. Page 11 TM-LT800 OPERATIONAL MANUAL FOR LARUE TACTICAL R.A.T. STOCK 8.0 Removal From Rifle Make sure firearm is unloaded. 1. Grasp RAT Stock in hand as shown, pull back on trigger (all the way) and slide stock off of receiver extension. Make sure Locking Switch is in “Unlocked” Position.

13. TM-LT800 FIRST EDITION September 2012 PUBLISHED BY: LaRue Tactical 850 County Road 177 Leander, Texas USA 78641 COPYRIGHT NOTICE: © 2012 LaRue Tactical, all rights reserved Before using this equipment, please be certain you have read, and understand this manual.