Download presentation
Presentation is loading. Please wait.
Published byJohan Colyar Modified over 10 years ago
2
Chapter 12 Fluid Flow
3
12-1 The Basic Equation of Steady-Flow 12-1-1 The Conversation of Mass A : Cross section area of flow duct c : Velocity of fluid v : Specific volume of fluid Differential form:
4
12-1-2 The Conversation of Energy Differential form:
5
12-1-3 Process Equation Usually the fluid flows too fast in a duct to exchange heat with its surroundings, so it undergoes an adiabatic process, then: pv k = const Differential form:
6
12-1-4 Velocity of Sound and Mach Number From Then The Velocity of Sound is denoted by
7
Mach Number Ma is defined as :
8
Ernst Mach was born on Feb. 18, 1838, d. Vaterstetten. He found an experimental proof for the Doppler Effect (Christian Doppler) and by inspection of fast moving projects proposed the Mach's principle. The "Mach Number" named after him describes the relation of a body's velocity to sonic speed. His attitude was characterized by empirical thinking based on scientific findings. One of his strictest opponents and critics was M. Planck. After retiring from the University in 1901 he was appointed to the upper chamber of the Austrian Parliament, a post he held for 12 years. He died in 1916
9
12-2 The Fluid Flow in Duct During the fluid flow in a duct, the properties of fluid changes along the stream line. In most situations this can be treated as a one-dimensional flow 12-2-1 The Pressure and Velocity From conservation of energy dh= - cdc du +d(pv)= - cdc du+pdv+vdp= -cdc
10
From the first law of thermodynamics: δq=du+pdv =0 Then: du+pdv+vdp= -cdc vdp= - cdc - vdp= cdc To increase the velocity of fluid( dc>0 ), the pressure must be decreased. This kind of duct is called Nozzle Or to decrease the velocity ( dc<0 ) of fluid to obtain a high pressure in a duct flow. This kind of duct is called diffuser
11
12-2-2 Velocity and The Cross Section Area of Duct From conservation of mass : From the process equation
13
As to a nozzle dc >0 (1)If the fluid velocity is subsonic, then ( Ma 2 -1 )<0 Therefore: dA<0 The nozzle’s shape should be as following: Subsonic flow convergent nozzle
14
(2)If the fluid velocity is ultrasonic, then ( Ma 2 -1 )>0 Therefore: dA>0 The nozzle’s shape should be as following: Ultrasonic flow divergent nozzle
15
(3)If the nozzle’s inlet velocity is subsonic, but outlet velocity ultrasonic, then: dA 0 The nozzle’s shape should be as following: Subsonic flow Ultrasonic flow convergent-divergent nozzle throat
16
As to a diffuser dc <0 (1)If the fluid velocity is subsonic, then ( Ma 2 -1 )<0 Therefore: dA>0 The diffuser’s shape should be as following: Subsonic flow
17
(2)If the fluid velocity is ultrasonic, then ( Ma 2 -1 )>0 Therefore: dA<0 The diffuser’s shape should be as following: Ultrasonic flow
18
(2) If the diffuser’s inlet velocity is ultrasonic, but outlet velocity subsonic, then: dA 0 The diffuser’s shape should be as following: Ultrasonic flow Subsonic flow
19
12-2-3 Applications Ram-jet engine Diffuser(compressor) combustion chamber nozzle
23
Rocket Space Shuttle
25
12-3 The Calculation of Nozzle 12-3-1 The Flux of Subsonic Nozzle We define P 2 /P 1 as compression ratio ε
26
12-3-2 The Critical Compression Ratio For convergent-divergent nozzle, the velocity at throat keeps as sound-velocity. This state is called critical state. The flux of this kind of nozzle is depend on that of throat. The Compression Ratio which is low enough to make the air flow at sound-velocity at the exit of nozzle is called the critical compression Ratio. It is denoted by ε c
27
εc=εc= 0.528 for air 0.546 for saturated steam 0.577 for superheated steam
28
The End of This Book Thank You
Similar presentations
© 2025 SlidePlayer.com. Inc.
All rights reserved.