1. Stephen Copeland, Xau Moua, Joseph Lane, Robert Akerson Client: Doug Taylor, John Deere Renewables Advisors: Dr. Manimaran Govindarasu, Dr.Venkataramana Ajjarapu

2.  Small scout towers capable of wirelessly transmitting measurements to large MET towers.  Wireless communication via radio transceivers on scout tower and MET tower.  Built-in mesh networking protocol

3. Signal Converter

4. Microcontroller Arduino Runs programmed code to send and receive data on mesh network Wireless Shield Xbee Provides easy form of adapter from transceiver to arduino due to header misalignment.

5. Transceiver Xbee-PRO digimesh 900 Provides mesh protocol Transmits data to other node Antenna 7" ½ wave dipole, bulkhead mount, RPSMA connector Omni-directional transmission of data

6. Wind Vane NRG#200P Provides wind direction Angle from North=(360’/Vin)*Vout Vout ranging from 0 to Vin Anemometer NRG#40C Provides wind speed Generates a sine wave whose frequency determines wind speed

7. Used to transform the Sine wave output from the Anemometer into a square wave which provides the arduino with a frequency that represents the measured wind speed.

9.  Scout Tower Code  Reads the Voltage Signal at selected pins of the Arduino  Aggregates data at a user specified interval Anemometer Output Signal Measures Pulse Width Converts Pulse Width to Wind Speed Sends Wind Speed to Serial Port

10.  Central transceiver code  Receives data from all other nodes in the mesh network  Aggregates all of the data  Prints new data set to a text file Reads Signal From Transceivers Sends Data To Computer Averages Wind Speed Data

11.  Sensor Testing  PCB Functionality Testing  Range Evaluations ◦ Elevated testing locations north of Ames  Power consumption ◦ Use of multi meters to measure current and voltage levels  Microcontroller ◦ Basic data communication

12.  Self Healing ◦ Selected modules turned off during transmission  Security ◦ Encryption of data being transmitted  Latency ◦ Receiving rate vs. data size  Casing ◦ Shock, vibration, realistic impact, and contact with water, ice, and snow.

13.  We connected the anemometer directly to an oscilloscope  Signal amplitude and frequency increases as wind speed increases

14.  We connected the wind vane to 5V power supply  Oscilloscope gives output voltage over time  Voltage varies as wind vane changes direction from 0 to 360 degrees

15.  Able to obtain a sine wave from the anemometer  Outputs a square wave with a frequency relative to the actual wind speed

16.  Wind speed in mph  Top node 1  Middle node 2  Both sampled and averaged every 10 seconds  Bottom average of node 1 and 2 calculated every 10 seconds

17.  Successful interfacing to the sensors and PCB for gathering of data  Aggregation of data from sensors  Storage of data as MPH in a text file from output

18.  Found optimal frequency of our antennas to be marker 1  Freq= 896.247MHz marker 1 freq=896.2473 MHz dB(S(1,1))=13.97 marker 2 freq=1.8014 GHz dB(S(1,1))=13.66

19.  We attached sensors to the roof of Coover Hall.  Successful transmission of data to motors lab from two nodes on roof  Simulated rugged terrain at Veenker golf course north of campus  Achieved an approximate range of 0.8 Km between nodes.

20.  Tested North of Ames on a flat gravel road  Achieved an approximate range of 1.75Km

21.  We spliced the USB cable between the device and PC  Connected inner USB wiring to a multi meter  Through the use of P=I*V we determined the required power to be around 0.5 Watts

22.  Placement of four nodes at a certain distance preventing direct communication between first and last node  Upon the removal of a middle node from the system the line of communication is not broken Receiving Node Node 1 Node 3 Node 2 User

23.  128-bit encryption is incorporated in the protocol for the transceivers  Client required only verification of encryption setting in transceivers

24.  Node 1 sends current time to node 2  Node 2 computes difference from it’s current time Time Synchronized Node 1Node 2

25. 2 nodes3 nodes4 nodes 2.9ms5.4ms7.1ms

26.  Remained water tight under running water  Absorbed force from hammer without damage to the inner components  Withstood 6℉ without damage

27.  Consists of sections of PVC and Brass connectors to ensure stability for the sensors  Nema-4 enclosure  Clamped to vent pipes on the roof of Coover Hall

31.  Utilizes aggregated wind speed from the roof of Coover  USB interface with transceiver and Desktop PC  Uses Labview Software to run motor  Motor is coupled to a wind turbine which simulates wind power generation.

32. http://seniord.ece.iastate.edu/may1101

33.  Use of renewable energy power source (wind or solar)  Integration of CFD into calculations for Wind Turbine project  Addition of more sensors to device ◦ GPS units ◦ Temperature Sensors ◦ Barometers This would allow for better analysis of potential wind generation locations

34.  Leland Harker, ISU Parts Shop  Senior Design Team SD MAY11-01  Doug Taylor, John Deere  Brad Luhrs & Bryan Burkhardt, DMACC  Dr. Manimaran Govindarasu  Dr. Venkataramana Ajjarapu

35. Any Questions?