1. Elcometer 510 Automatic Pull Off Adhesion Gauge March 2014

2. … the new Elcometer 510 Model S & T
Elcometer are pleased to announce the launch of their new Elcometer 510 Automatic Pull Off Adhesion Tester…
… the new Elcometer 510 Model S & T

3. Elcometer 510 – Key Features
Automatic hydraulic pump ensures smooth and continuous pressure application for consistent repeatable results
Dust and water resistant
rugged design to IP64
Fully adjustable pull rates 0.1 – 1.4MPa/s (15-203psi) to meet national and international standards
Interchangeable units:
MPa, psi, N/mm² and N
Can be used with 10, 14.2, 20 and 50mm diameter dollies
User definable measurement range with an accuracy of ±1% of full scale:
10mm dolly: 100MPa (14400psi)
14.2mm dolly: 50MPa (7200psi)
20mm dolly: 25MPa (3600psi)
50mm dolly: 4MPa (580psi)
User definable limits with unique pressure hold and release function
A range of standard and thin substrate actuator skirts (compatible with the Elcometer 506) are available for testing coatings on thick, thin, flat or convex substrates
Store up to 10,000 readings, with individual pull rate graphs in up to 2,500 alpha numerical batches, complete with attribute failure information
USB and Bluetooth® data output - Compatible with ElcoMaster™ App for iPhone, iPod, iPad and Android mobile devices .

4. The Model Range

5. The Model Range Elcometer 510 has two models:
Model S: An entry level gauge, powered by batteries, with defined pull rates, 60 reading memory & USB output to ElcoMaster 2.0;
Model T: All the features of the Model S, but can be powered by batteries and/or AC Mains, USB & Bluetooth (Android and iPhone, iPad, iPod), up to 60,000 readings in 2,500 alphanumeric batches which can store:
the reading,
cohesive/ adhesive attribute information,
pull rate graph
The Model T also has user a definable limit with a unique
‘Pull to Limit’ setting and an in field adhesion calibration
verification mode.

6. The Model Range Key Features Model S Model T
Tough, impact, waterproof and dust resistant gauge 
Bright LCD colour scratch & solvent resistant screen with ambient light sensor
Calibration Certificate supplied as standard
2 year warranty
Data Output
USB
USB & Bluetooth
On Screen Statistics
Interchangeable dolly diameters – 10 / 14.2 / 20 / 50mm
Measurement units – MPa, psi, Nmm-2, Newtons
Trend graph (Run chart) – last 20 readings
PC Command – start & stop the gauge from your PC or mobile device
Pull rate graph – load v time

7. The Model Range Key Features Model S Model T
Measurement Range (using 20mm dolly)
2 – 25MPa
Memory
60 readings
in 1 batch
60,000 readings in 2,500 batches
Date & Time stamped readings 
Store cohesive & adhesive attribute data against each reading
User selectable limit with limit hold feature
Field calibration verification mode
Select from a defined list of pull rates
10mm: , 2.00, 3.00, 4.00, 5.00 MPa/s
14.2mm: , 0.7, 1.4, 2.0, 2.5 MPa/s
20mm: , 0.3, 0.7, 1.0, 1.2 MPa/s
50mm: , 0.08, 0.12, 0.16, 0.20 MPa/s
User selectable pull rates
10mm: MPa/s in 0.1MPa/s steps
14.2mm: MPa/s in 0.1MPa/s steps
20mm: MPa/s in 0.1MPa/s steps
50mm: MPa/s in 0.01MPa/s steps

8. The Reading Display

9. The Reading Display

10. The Reading Display

11. The Packing List
20mm Kit:
Elcometer 510 Adhesion Tester with 20mm dollies (x10),
Standard 20mm skirt,
20mm cutter,
Araldite glue,
Abrasive pad,
Shoulder harness,
Plastic carry case,
16x rechargeable AA (MiMH) batteries & external battery charger (UK, EU, US, AUS),
USB cable & ElcoMaster 2.0 CD,
Calibration certificate,
Operating instructions, and
AC Mains Power Cable (Model T)
Each model is available as either a 20mm or 50mm (concrete) inspection kit

12. The Packing List
Each model is available as either a 20mm or 50mm (concrete) inspection kit
50mm Kit:
Elcometer 510 Adhesion Tester with 50mm dollies (x6),
Standard 50mm skirt,
50mm drill arbor & cutter,
Araldite glue,
Abrasive pad,
Shoulder harness,
Plastic carry case,
16x rechargeable AA (MiMH) batteries & external battery charger (UK, EU, US, AUS),
USB cable & ElcoMaster 2.0 CD,
Calibration certificate,
Operating instructions, and
AC Mains Power Cable (Model T)

13. Key Features Explained

14. Pull to Limit / Pull to Max

15. Pull To Limit / Pull to Max
The Elcometer 510 Model T can have a user defined limit:
Some specifications require coatings to be tested to a maximum pull-off strength. Users can set a limit value and a limit hold time (how long pressure is maintained at the limit value until the gauge rewinds to zero) and then select:
Pull to Limit: the gauge will increase the pressure at the defined pull rate until the limit has been reached and maintained for the set hold time or the dolly pulls off, whichever occurs first after which, the gauge re-winds to ‘zero’; or
Pull to Maximum: the gauge will increase the pressure until the maximum pressure rate for the selected dolly size / pull rate combination has been reached or the dolly pulls off, whichever occurs first, at which point the gauge automatically re-winds to ‘zero’.
A limit can be set for individual readings (when in Immediate mode) or individual limits can be set for each batch (when in Batching).

16. Pull Rate Graph

17. Pull Rate Graph
The Elcometer 510 Model T can also store the individual pull rate graph
This unique feature allows users to record the load against time graph and display it on an inspection report.
A graphical representation of the increase in pressure applied over time of test, based on the pull rate and dolly diameter set for the batch.
The graph is displayed on screen above the pressure reading and attribute data (if set) using the resolution defined by the user via Batch/New Batch/Rate Graph.
The individual graphs can be reviewed within the gauge under
Batch/ Review Batch/ Readings & Rate Graph

18. Failure Attributes

19. Cohesive / Adhesive Failure Attributes
Many National and International Standards, including ISO 4624 & ASTM D4541, require the user to record not only the pull-off force but also the nature of the failure.
The bottom of the dolly is examined alongside the ‘fractured’ coating, the percentage cohesive and % adhesive failure is assessed and recorded together with the pull off reading.
In accordance with Standards, the information is displayed as: 
##.## MPa N% A M% A/B,
Where:
##.## is the Pull Force in MPa or other measurement unit (psi, N or Nmm-2)
N% is the Cohesive failure percentage (to the nearest 10%) and ‘A’ is the Cohesive failure layer M% is the Adhesive failure percentage (to the nearest 10%) and ‘A/B’ is the Intercoat adhesive failure layers

20. Cohesive / Adhesive Failure Attributes
d The number of layers can be user defined for each batch via Batch/New Batch/Number of Layers. This will affect the number of layers available for selection during attribute recording. The maximum number of layers available is five, excluding the substrate and glue.

21. Cohesive / Adhesive Failure Attributes
For example:
14.26 MPa 40% B 30% B/C
the coating fractured at a pull force of MPa,
with 40% of the dolly area associated with cohesive failure of layer 1 and
30% of the dolly area associated with an intercoat adhesive failure between layers 1 and 2
The cohesive failure percentage plus the adhesive failure percentage does not have to equal 100%, but cannot exceed 100%
Should the dolly not fail, the pull force is recorded together with the greater than symbol (>) the pull force obtained.
For example: >25MPa 40% B 30% B/C

22. Cohesive / Adhesive Failure Attributes
In addition to recording the % cohesive and adhesive failure, ISO 4624 & ASTM D4541, require the user to also record whether the dolly was cut (and if so, with what type of tool; knife or dolly cutter); and if a support ring was used (and if so, the dimensions of the support ring).
The Elcometer 510 also allows this information to be recorded within the batch header information – which is sent to ElcoMaster alongside the measurement and attribute data.
Each Elcometer 510 has an internal support ring connected to the actuator head – this is called the Skirt. The user identifies the skirt type used (thin substrate, standard skirt, etc.) within the batch header, and the dimensions of the appropriate support ring are reported within ElcoMaster.

23. Verifying the Gauge Calibration & Accuracy

24. Verifying the Gauge Calibration & Accuracy
The Elcometer 510 is factory calibrated however, the calibration and accuracy of the gauge can be verified in the field at any time using the Elcometer Adhesion Verification Unit (AVU).
Connect the Elcometer 510 to the Elcometer AVU, select “Menu/ Verify Calibration” and follow the on screen instructions.
The calibration verification process tests the gauge’s performance at three pressure points.

25. ElcoMaster 2.0

26. ElcoMaster™ 2.0
The new Elcometer 510 is compatible with ElcoMaster™ 2.0 and ElcoMaster Mobile:
Live gauge readings, and graphs can be transferred and stored in a batch within ElcoMaster™, as each measurement is taken.
Batch data can be downloaded to PC or mobile device for archiving and report generation.
Users can upgrade their gauges to the latest software release in the field.
Compatible with Cloud Computing; data can be accessed by authorised users of the Cloud Account via secure log-in from anywhere in the world.
Compatible with iPod, iPhone, iPad and Android mobile devices.

27. The Menu Structure

28. inspection equipment
Elcometer 510 Model S

29. inspection equipment
Elcometer 510 Model T

30. Certificates & Warranty

31. Calibration Certificates
Each Elcometer 510 is supplied with a
Calibration Certificate as standard.
Gauges are calibrated using factory reference load cell unit, in accordance with Elcometer’s certification procedures.

32. 2 Year Extended Warranty
The new Elcometer 510 Automatic Pull-Off Adhesion Tester is supplied with one year warranty as standard.
Customers can extend this warranty free of charge within 60 days of purchase, by simply clicking the “Extend Your Warranty” tab on the Elcometer website.
An A6 card is supplied with all gauges informing the customer of this 2nd year extension.