1. 23022 Series Evaporator Features:
One dynamically balanced twin shaft blower assembly
with long life 12 volt DC permanent magnet motors with
full ball bearings and extended life brushes.
Orifice tube/accumulator in lieu of TXV used in conjunction
with highly efficient crosshatch copper tube and an aluminum fin
coil for maximum capacity output and durability.
Standard manual controls or fully automatic. Electronic
controls are pre-wired relays and circuit breakers. Relay board
with electrical diagnostic LEDs can be mounted at evaporator
or control panel at driver.
Utilizes our uniquely designed mounting system, eliminating
the need to drill holes through the roof.
Available with heat.
Specifications:
40,000 BTU/hr cooling capacity
495 cfm
Amp Draw High – 19 amps
3 speed fans
12 or 24 volts
Dimensions: ”W x 9”H x ”D
Weight – 52 lbs
Key Components:
Coil: A
Blower Assembly: A
Orifice Tube: A
Front/Rear Mount Cover: A
Side Mount Cover: A
In the interests of continuous improvement, specifications are subject to change without notice.

2. 23023 Series Evaporator Features:
Two dynamically balanced twin shaft blower assemblies
with long life 12 volt DC permanent magnet motors with
full ball bearings and extended life brushes.
Orifice tube/accumulator in lieu of TXV used in conjunction
with highly efficient crosshatch copper tube and an aluminum
fin coil for maximum capacity output and durability.
Standard manual controls or fully automatic. Electronic
controls are pre-wired relays and circuit breakers. Relay board
with electrical diagnostic LEDs can be mounted at evaporator
or control panel at driver.
Utilizes our uniquely designed mounting system, eliminating
the need to drill holes through the roof.
Available with heat.
Specifications:
53,000 BTU/hr cooling capacity
1200 cfm
Amp Draw High – 30 amps
3 speed fans
12 or 24 volts
Dimensions: 42”W x 10”H x 19.5”D
Weight – 60 lbs
Key Components:
Coil: A
Blower Assembly: A
Orifice Tube: A
Front/Rear Mount Cover: A
Side Mount Cover: A

3. 23047 Series Evaporator Features:
Larger 67,000 BTU Capacity for those critical midsize applications.
Two dynamically balanced twin shaft blower assemblies
with long life 12 volt DC permanent magnet motors with
full ball bearings and extended life brushes.
Orifice tube/accumulator in lieu of TXV used in conjunction
with highly efficient crosshatch copper tube and an aluminum
fin coil for maximum capacity output and durability.
Standard manual controls or fully automatic. Electronic
controls are pre-wired relays and circuit breakers. Relay board
with electrical diagnostic LEDs can be mounted at evaporator
or control panel at driver.
Utilizes our uniquely designed mounting system, eliminating
the need to drill holes through the roof.
Available with heat.
Specifications:
67,000 BTU/hr cooling capacity
1400 cfm
Amp Draw High – 30 amps
3 speed fans
12 or 24 volts
Dimensions: 42”W x 10”H x 19.5”D
Weight – 60 lbs
Condenser Options:
,000 BTU Skirt Condenser
,000 BTU Rooftop Condenser

4. 23036 Series Evaporator Features:
This heavy-duty, high capacity ceiling mount unit provides cooling
for a variety of vehicles with large passenger compartments. It
easily can substitute for two single blower or single and double AC
units.
Due to the unit consisting of two independent evaporators, it can be
installed as A) one stand alone or tie in system, or B) two indepen-
dent systems, with two you will get a 30 amp draw plus a 15 amp
draw. The latter option gives the option of turning on either a single
system or both systems.
Three dynamically balanced twin shaft blower assemblies that
utilize long life 12 volt DC permanent magnet motors with full ball
bearings and extended life brushes.
An orifice tube used in conjunction with highly efficient enhanced
copper tube and an aluminum fin coil for maximum capacity.
Standard manual controls or fully automatic. Electronic controls are
pre-wired relays and circuit breakers mounted to the evaporator.
Utilizes our uniquely designed mounting system that eliminates the
need to drill through the roof.
Available with heat.
Specifications:
86,000 BTU/hr cooling capacity
105,000 BTU/hr heating capacity
1800 cfm
Amp Draw High – 30 plus 15
3 speed fans
12 volt
Dimensions: 42”W x 10”H x 19.5”D
Weight – 95 lbs
Key Components:
Coil: A
Blower Assembly: A
Orifice Tube: A
Rear Mount Cover: A

5. 22035 Series Evaporator Features:
This ceiling mount unit provides cooling to any bus, van, or other
vehicle’s passenger compartment. The low profile unit is
specifically designed for vehicles with low head clearance.
An orifice tube used in conjunction with highly efficient enhanced
copper tube and an aluminum fin coil for maximum capacity output
and durability.
Standard manual controls or fully automatic. Electronic controls are
pre-wired with relays and circuit breakers mounted to the evaporator.
durable ABS formed drain pan and outlet plenum with fully
adjustable louver vents.
Utilizes our uniquely designed mounting system that eliminates the
need to drill through the roof.
Specifications:
30,000 BTU/hr cooling capacity
35,000 BTU/hr heating capacity
600 cfm
Amp Draw High – 20.6
3 speed fans
12 volt
Dimensions: 35 3/4”W x 6 1/4”H x 14 1/16”D
Weight – 38 lbs
Key Components:
Coil: A
Blower Assembly: A
Orifice Tube: A
Rear Mount Cover: A

6. 23046 Series Evaporator Weight – 56 lbs Features:
Low profile design for more headroom clearance.
Two dynamically balanced twin shaft blower assemblies
with long life 12 volt DC permanent magnet motors with
full ball bearings and extended life brushes.
Orifice tube/accumulator in lieu of TXV used in conjunction
with highly efficient crosshatch copper tube and an aluminum
fin coil for maximum capacity output and durability.
Standard manual controls or fully automatic. Electronic
controls are pre-wired relays and circuit breakers. Relay board
with electrical diagnostic LEDs can be mounted at evaporator
or control panel at driver.
Utilizes our uniquely designed mounting system, eliminating
the need to drill holes through the roof.
Specifications:
53,000 BTU/hr cooling capacity
1200 cfm
Amp Draw High – 30 amps
3 speed fans
12 or 24 volts
Dimensions: 41.7”W x 7.0”H x 21.04”D
Weight – 56 lbs
Key Components:
Coil: A
Blower Assembly: A
Orifice Tube: A
Rear Mount Cover: A

7. 23048 Series Evaporator Weight – 52 lbs Features:
Low profile design for more headroom clearance.
One dynamically balanced twin shaft blower assemblies
with long life 12 volt DC permanent magnet motors with
full ball bearings and extended life brushes.
Orifice tube/accumulator in lieu of TXV used in conjunction
with highly efficient crosshatch copper tube and an aluminum
fin coil for maximum capacity output and durability.
Standard manual controls or fully automatic. Electronic
controls are pre-wired relays and circuit breakers. Relay board
with electrical diagnostic LEDs can be mounted at evaporator
or control panel at driver.
Utilizes our uniquely designed mounting system, eliminating
the need to drill holes through the roof.
Specifications:
40,000 BTU/hr cooling capacity
600 cfm
Amp Draw High – 15 amps
3 speed fans
12 volts
Dimensions: 41.7”W x 7.0”H x 21.04”D
Weight – 52 lbs
Key Components:
Coil: A
Blower Assembly: A
Orifice Tube: A
Rear Mount Cover: A

8. 23045 Series Evaporator Features:
Two dynamically balanced twin shaft blower assemblies
with long life 12 volt DC permanent magnet motors with
full ball bearings and extended life brushes.
Orifice tube/accumulator in lieu of TXV used in conjunction
with highly efficient crosshatch copper tube and an aluminum
fin coil for maximum capacity output and durability.
Standard manual controls or fully automatic. Electronic
controls are pre-wired relays and circuit breakers. Relay board
with electrical diagnostic LEDs can be mounted at evaporator
or control panel at driver.
Utilizes our uniquely designed mounting system, eliminating
the need to drill holes through the roof.
Available with heat.
Specifications:
55,000 BTU/hr cooling capacity
1200 cfm
Amp Draw High – 30 amps
3 speed fans
12 or 24 volts
Dimensions: ”W x 13.95”H x 7.45”D
Weight – 65 lbs
Key Components:
Coil: X A
Blower Assembly: A
Orifice Tube: A
Front Mount Cover:
Rear Mount Cover: (shown)

9. 23044 Series Evaporator Features:
One dynamically balanced twin shaft blower assembly
with long life 12 volt DC permanent magnet motors with
full ball bearings and extended life brushes.
Orifice tube/accumulator in lieu of TXV used in conjunction
with highly efficient crosshatch copper tube and an aluminum
fin coil for maximum capacity output and durability.
Standard manual controls or fully automatic. Electronic
controls are pre-wired relays and circuit breakers. Relay board
with electrical diagnostic LEDs can be mounted at evaporator
or control panel at driver.
Utilizes our uniquely designed mounting system, eliminating
the need to drill holes through the roof.
Specifications:
45,000 BTU/hr cooling capacity
600 cfm
Amp Draw High – 15 amps
3 speed fans
12 or 24 volts
Dimensions: ”W x 13.95”H x 7.45”D
Weight – 65 lbs
Key Components:
Coil: X A
Blower Assembly: A
Orifice Tube: A
Front Mount Cover:
Rear Mount Cover: (shown)

10. 25031 Series Condenser Features:
Two 14” diameter fans to cover a higher percentage of the coil, 307 sq.
in. moving more air than traditional condensers. High performance
motors with extended brush life. Motor shafts are seated to the case
which is sealed with Viton O-rings to provide superior water resistance.
Counter flow coil circuitry and cross hatch tubing maximizes the
refrigerant heat rejection and provides superior sub-cooling.
The unit is fabricated from 16 ga. A-60 galvanealed steel with the
individual metal components finished with an E-Kote epoxy coating for
superior durability and resistance to rust.
Design allows for installation without having to cut condenser intakes in
the skirt of the bus, (school bus only) providing a more aesthetic OEM
look to the bus.
Specifications:
78,000 BTU/hr capacity
2500 cfm
Amp Draw High – 22 amps
12 or 24 volts
Dimensions: 38.5”W x 20.25”H x 7.125”D
Weight – 62 lbs
Key Components:
Coil: A
Fan: B

11. 25046 Series Condenser Features:
Two 14” diameter fans to cover a higher percentage of the coil, 307 sq.
in. moving more air than traditional condensers. High performance
motors with extended brush life. Motor shafts are seated to the case
which is sealed with Viton O-rings to provide superior water resistance.
Counter flow coil circuitry and cross hatch tubing maximizes the
refrigerant heat rejection and provides superior sub-cooling.
The unit is fabricated from 16 ga. A-60 galvanealed steel with the
individual metal components finished with an E-Kote epoxy coating for
superior durability and resistance to rust.
Design allows for installation without having to cut condenser intakes in
the skirt of the bus, (school bus only) providing a more aesthetic OEM
look to the bus.
Specifications:
92,000 BTU/hr capacity
2500 cfm
Amp Draw High – 22 amps
12 or 24 volts
Dimensions: 38.5”W x 20.25”H x 7.125”D
Weight – 67 lbs

12. 25034 Series Condenser Features:
Two 14” diameter high performance fans. High performance
motors with extended brush life. Motor shafts are seated to the case
which is sealed with Viton O-rings to provide superior water resistance.
Highly efficient 6mm coil design provides superior refrigerant heat
rejection and provides superior sub-cooling.
The unit is fabricated from 16 ga. A-60 galvanealed steel with the
individual metal components finished with an E-Kote epoxy coating for
superior durability and resistance to rust.
Design allows for installation without having to cut condenser intakes in
the skirt of the bus, (school bus only) providing a more aesthetic OEM look to
the bus.
Specifications:
62,000 BTU/hr capacity
2500 cfm
Amp Draw High – 22 amps
12 or 24 volts
Dimensions: 33.5”W x 11”H x 15”D
Weight – 62 lbs
Key Components:
Coil: A
Fan: B

13. 25035 Series Condenser Features:
One 14” diameter high performance fan. High performance
motor with extended brush life. Motor shafts are seated to the case
which is sealed with Viton O-rings to provide superior water resistance.
Highly efficient 6mm coil design provides superior refrigerant heat
rejection and provides superior sub-cooling.
The unit is fabricated from 16 ga. A-60 galvanealed steel with the
individual metal components finished with an E-Kote epoxy coating for
superior durability and resistance to rust.
Design allows for installation without having to cut condenser intakes in
the skirt of the bus, (school bus only) providing a more aesthetic OEM look to
the bus.
Specifications:
35,000 BTU/hr capacity
1275 cfm
Amp Draw High – 11 amps
12 volt
Dimensions: 33.5”W x 11”H x 15”D
Weight – 52 lbs
Key Components:
Coil: B
Fan: C

14. 25045 Series Rooftop Condenser
Features:
Low Profile roof top design with overall height of 7 inches.
Two 14” diameter fans to cover a higher percentage of the coil, moving more air than traditional condensers.
High performance motors with extended brush life. Motor shafts are seated to the case which is sealed with Viton O-rings to provide superior water resistance.
Counter flow coil circuitry and cross hatch tubing maximizes the
refrigerant heat rejection and provides superior sub-cooling.
The unit is fabricated from 16 ga. A-60 galvanealed steel with the
individual metal components finished with an E-Kote epoxy coating for
superior durability and resistance to rust.
Cover made of high impact molded plastic
Specifications:
78,000 BTU/hr capacity
2500 cfm
Amp Draw High – 22 amps
12 or 24 volts
Dimensions: 40” L x 40.5” W x 7” H
lbs

15. 25047 Series Rooftop Condenser
Features:
Low Profile roof top design with overall height of 7 inches.
Two 14” diameter fans to cover a higher percentage of the coil, moving more air than traditional condensers.
High performance motors with extended brush life. Motor shafts are seated to the case which is sealed with Viton O-rings to provide superior water resistance.
Counter flow coil circuitry and cross hatch tubing maximizes the
refrigerant heat rejection and provides superior sub-cooling.
The unit is fabricated from 16 ga. A-60 galvanealed steel with the
individual metal components finished with an E-Kote epoxy coating for
superior durability and resistance to rust.
Cover made of high impact molded plastic
Specifications:
100,000 BTU/hr capacity
2500 cfm
Amp Draw High – 22 amps
12 or 24 volts
Dimensions: 40” L x 40.5” W x 7” H
lbs

16. ACC “Tropicool” Roof Mount HVAC System
Features:
Low Roof Profile of only 6.9 inches at centerline of bus
Unit width allows the direct discharge of evaporator air into the coach
without the use of transitions required by other systems.
Six (6) biaxial centrifugal type blower fans
Three (3) axial-flow type condenser fans
High impact fiber glass housing
R134a Refrigerant
Available in both single loop or dual loop refrigeration circuits for
single or dual compressor applications
Specifications:
96,000 BTU/hr cooling capacity
120,000 BTU/hr heating capacity
Automatic or Manual Control
2400 Evaporator cfm
Amp Draw amps (12 Volts)
3 speed fans
12 or 24 volts
Dimensions: “ L x 73.3” W x 6.9” H
Weight 455 lbs

17. ACC Climate Control ATCO Air-O Crimp a/c Hose System
Features:
Provides a Reliable Leak Free Crimp
One piece clamp assembly with stainless steel clamps
Disposable clamp locator insures proper fitting alignment
Qualified to SAE J2064 Specification
Lowest Refrigeration Permeation Rate
Low Moisture Ingression Rate
Superior Abrasion Resistance – 3x That of Competition
Specifications:
ATCO 3800 Barrier Hose
ATCO a/c Series Hybrid/Elastomer Fittings
Use with PAG Oil
Available Air Crimp Gun, Model 3801
Available Manual Crimping Pliers, Model 3802 (flat), or 3803 (90º)
Available Cutter, Model 3541 Kwikcut Hose Cutter