2. Kettle fires Storage of flammables near heat sources Mechanical equipment fires Flash over with primer wash Building fire caused by customer Cigarette smoking on the roof or around flammables Sparks from cutting metal deck Electrical fires or exposed wires Smoldering asphalt under roof

3. 3 Components of fire: 1. Fuel 2. Heat 3. Oxygen All three components are needed for a fire to survive! Take one of the three away, the fire will not survive!

4. CLASS A - Ordinary Combustibles CLASS B - Flammable or Combustible Liquids CLASS C - Electrical CLASS D - Combustible Metals

5. Examples: Paper Insulation Dried Adhesives Fiberboard Clothing Wood Deck

6. Examples: Gasoline Primer Wash Splicing Cement Adhesives Coatings Propane

7. Points to remember: Never use water to extinguish! Check all cords and equipment before use De-energize when not in use Exposed wires are a fire hazard

8. Class A - For class A fires only Class B - For class B fires only Class AB - For both class A and B fires Class ABC - For class A, B, and C fires

9. What type of fire is this going to be?

10. 1.2.3. Which is the proper extinguisher to use for suppression of the previous fire?

11. P. A. S. S. System 1Pull - Pull pin

12. 2Aim - Aim nozzle at base of the fire 3Squeeze - Squeeze the handle together

13. 4S weep - Sweep back and forth

14. Fire extinguishers can save lives and property Only attempt to extinguish a fire if it is safe and you have been trained on proper use Evacuate the roof if the fire is out of control

15. Recommended Procedure Shut the lid Shut off the fuel source Remember to do both! Use extinguisher when: Fire is no longer contained in kettle Fire is out of Control *NEVER use water!

16. Review escape plan before work begins Never set up the kettle near access to the roof Keep the fire extinguishers in your work area Foremen, keep cell phone on you at all times

17. Proper Torch Assembly –Follow all Manufacturer’s Recommendations –Use only approved connection equipment –Hand tighten parts and do not force connection –Use open end wrench to complete assembly –Do not use any type of thread sealant as they may be flammable

18. Inspect all equipment for damage before use Inspect propane cylinder for dirt Close cylinder valve tightly Attach torch following Manufacturer’s Recommendations Complete leak test using soapy water –Leaks will cause bubbles to form

19. If leak is detected, close cylinder valve and disconnect all parts –Attempt to reassemble –If leaks still exist, discontinue use and replace torch Never use open flame to check for leaks! Never use any type of mastic or putty between parts of a torch.

20. Wear required PPE –Eye protection, gloves, long clothing to cover skin Prepare work area by clearing away debris Have extinguishers present and secure propane tank Alert other workers and keep them away Open cylinder and keep torch away from body Use striker to ignite gas and adjust flame –NEVER USE CIGARETTE LIGHTERS OR MATCH

21. Always assume a torch at rest is lit Use leg stand to support torch Shut torch off when not in use Never leave torch unattended Never operate within 3 feet of other workers Never point torch towards flammable objects or areas you can not see clearly

22. Use caution when using torch around: –Roof openings, units & drains –Roofing materials and combustible deck

23. Never turn propane cylinder on its side –This does not increase fuel supply and is dangerous Never apply open flame to defrost cylinders Use caution when walking backwards –Use all required fall protection –Be aware of your surroundings –Have another employee serve as spotter

24. It is not recommended to use a torch to dry a roof or a deck –Using a torch in this manner is approved by NRCA/ CERTA for only specific situations. –Fire can enter a building from anything that disturbs the field.

25. Always disconnect torches at end of work day Inspect all components for damage Replace damaged components Set torch on side and close cylinder valve Squeeze torch trigger to purge remaining gas Close all valves and disconnect torch Properly store equipment & secure cylinders

26. Torches that will not be used for more than 30 days should be completely disassembled for storage.

27. Propane Cylinders & Valves –Manufactured with safety controls Protective Collar Cylinder Valve Foot Ring

28. Propane Cylinders –Protective Collar Guard to protect cylinder valve Designed to withstand tipping or damage –30 pound weight dropped from 4 feet Do not use if protective collar is missing NEVER ATTACH RIGGING TO THE COLLAR

29. Propane Cylinders –Cylinder Valve Contains OPD (Overfill Protection Device) –Will prevent against overfilling of tank –Required for all propane cylinders Always use hand wheel to adjust controls –Open slowly and do not force –Remove from service if hand wheel is damaged Pressure relief valve –Designed to protect cylinder –Do not try to repair leaking valves

30. Propane Cylinders –Foot Ring Cylinders must remain upright Foot ring helps to stabilize Cylinders must be secured –Guard Rail –Milk Crate –Bungee Cord

31. When cutting through metal deck and during the use of torch work: –Mark off 10ft area below –Have a crew member stand below outside marked area to watch for smoke and fire –Supply him with a hard hat, safety glasses, and a fully charged ABC rated fire extinguisher –Should remain on duty for at least one hour past work incase of smoldering

32. All flammable and combustible materials must be properly labeled Labels should be kept clean and easily noticeable All D.O.T. vehicles must have proper placards Never remove or alter labels

33. FIRE HAZARD Flash Points: 0-Will not burn 1-Above 200 o F 2-Below 200 o F 3-Below 100 o F 4-Below 73 o F

34. Hot Pipe Secure to 8’ Rail 20 lb. Fire Extinguisher Rubber Matting Under Kettle Area Flagged Off Correctly Building Tarped Asphalt Stored Neatly Propane Secure 10’ from Flame Proper PPE Worn Wheels Chalked No Windows

35. Area flagged off 20 lb. Fire extinguisher present Fuel set 10 feet from ignitable source & secured in place Plywood under kettle if set on new roof Proper PPE worn

36. PPE Required for Kettle Operations: Hardhat with Attached Face Shield - the face shield prevents splashes from reaching the face and upper neck Leather Gloves - cuffs must be long enough to be tucked under sleeves Long Pants with No Cuffs - cuffs on pants may hold asphalt and allow it to burn you Long Sleeved Sweatshirt - preferably hooded to protect the back of your neck

37. While working with hot asphalt on the roof employees must wear:Leather gloves, Safety glasses, Long sleeved shirt, Long pants w/ no cuffs, and proper boots * Never use glue buckets or primer wash cans to transport hot, only hot buckets or approved containers Note: When pouring asphalt from pipe, a face shield is also required to be worn

38. Always use caution with flammable materials and open flames Think Safety First to avoid burns Fire watch is needed for spark generating work Only use strikers to light torches Never use gasoline to clean hands Only you can prevent roof fires!