1. Ch.1 Introduction Optoelectronic devices: - devices deal with interaction of electronic and optical processes Solid-state physics: - study of solids, through methods such as quantum mechanics, crystallography, electromagnetism and metallurgy Elemental semiconductors: - Si, Ge,..etc. - indirect bandgap, low electric-optics conversion efficiency Compound semiconductors - III-V (e.g. GaN, GaAs), II-VI - direct bandgap, high electric-optics conversion efficiency GaAs, InP - higher mobility than Si, Ge, - energy band gap, Eg: 1.43 (GaAs), 1.35 (InP) - most common substrate, used to grow up compound semiconductors

2. Periodic Table

3. Band structure Band structure: - results of crystal potential that originates from equilibrium arrangement of atoms in lattice - directed from potential model and electron wave equation (Schrodinger equation) time-dependent Schrodinger equation E: electron energy, φ:wave equation, m: electron mass, ħ: Plank constant

4. Electron energy band diagram v.s. wave number

5. Energy bandgap v.s. lattice constant

6. Bonding in solids Van der Waals bonding: formation of dipoles between atoms and their electrons e.g.: inert gas, like Ar Ionic bonding: electron exchange between atoms produces positive and negative ions which attract each other by Coulomb-type interactions e.g. NaCl, KCl covalent bonding sharing of electrons between neighboring atoms e.g.: elemental and compound semiconductors Metallic bonding: valence electrons are shared by many atoms (bonding not directional, electron free or nearly free contributed to conductivity) e.g.: Zn

7. Body-Centered Cubic (BCC) structure http://stokes.byu.edu/bcc.htm e.g. iron, chromium, tungsten, niobium

8. Face-Centered Cubic (FCC) structure http://stokes.byu.edu/fcc.htm e.g.: aluminum, copper, gold, silver

9. Diamond Cubic (FCC) structure http://zh.wikipedia.org/zh-tw/File:Diamond_Cubic-F_lattice_animation.gif

10. Zincblende structure Diamond structure, Zincblende structure e.g.: aluminum, GaAse.g.: Si, Ge

11. Atomic arrangement in different solids

12. Dislocation & strain Dislocation occurs if - epitaxial layer thickness > h c (critical thickness), or - epitaxial layer thickness < h c, but with large mismatch Strain occurs if - epitaxial layer thickness < hc, and with small mismatch

13. Strain semiconductor a) lattice match b) compressive strain c) tensile strain Strain offer flexibility for restriction of lattice mismatch

14. Crystal Growth Bulk growth: - furnace growth - pulling technique Epitaxial growth: - Liquid Phase Epitaxy (LPE) - Vapor Phase Epitaxy (VPE), or termed Chemical Vapor Deposition (CVD) - Molecular Beam Epitaxy (MBE)

15. Epitaxy epi means “above” taxis means “in order manner” epitaxy can be translated to “to arrange upon” with controlled thickness and doping subtract acts as a seed crystal, deposited film takes on a lattice structure and orientation identical to the subtract different from thin film deposition that deposit polycrystalline or amorphous film - homoepitaxy: epi and subtract are with the same material epi layer more pure than subtract and have different doping level - hetroepitaxy: used for - Si-based process for BJT and CMOS, or - compound semiconductors, such as GaAs

16. Epitaxy Material Growth Methods Liquid Phase Epitaxy Vapor Phase Epitaxy (VPE), or termed Chemical Vapor Deposition (CVD) - formation of condensed phase from gas of different chemical composition - distinct from physical vapor deposition (PVD) such as sputtering, e-beam deposition, MBE (condensation occurs without chemical change) - gas stream through a reactor and interact on a heated subtract to grow epi layer Molecular Beam Epitaxy

17. Doping of Semiconductors Intrinsic materials: undoped - Undoped materials by epitaxy technology have more carriers than in intrinsic material. e.g. GaAs: 10 13 /cm 3 (instrinsic carrier concentration: 1.8x10 6 /cm 3 ) - impurity comes from source materials, carrier gases, process equipment, or subtract handle Extrinsic materials: - n-type: III sub-lattice of III-V compound is substituted by V elements: impurity terms “donor” - p-type: V sub-lattice of III-V compound is substituted by III elements: impurity terms “acceptor” http://www.siliconfareast.com/sigegaas.htm

18. Optical fiber - lowest loss at 1.55 um - lowest dispersion” 1.3 um

19. Energy band theory