1. Frequency response I
As the frequency of the processed signals increases, the effects of parasitic capacitance in (BJT/MOS) transistors start to manifest
The gain of the amplifier circuits is frequency dependent, usually decrease with the frequency increase of the input signals
Computing by hand the exact frequency response of an amplifier circuits is a difficult and time-consuming task, therefore approximate techniques for obtaining the values of critical frequencies is desirable
The exact frequency response can be obtained from computer simulations (e.g SPICE). However, to optimize your circuit for maximum bandwidth and to keep it stable one needs analytical expressions of the circuit parameters or at least know which parameter affects the required specification and how

2. Frequency response II
The transfer function gives us the information about the behavior of a linear-time-invariant (LTI) circuit/system for a sinusoidal excitation with angular frequency
This transfer function is nothing but the ratio between the Fourier transforms of the output and input signals and it is also called the frequency response of the LTI circuit.
represents the gain magnitude of the frequency response of the circuit, whereas is the phase of frequency response. Often, it is more convenient to express gain magnitude in decibels.
To amplify a signal without distortion, the amplifier gain magnitude must be the same for all of the frequency components

3. Frequency response of amplifers
A bode plot shows the the gain magnitude and phase in decibles versus frequency on logarithmic scale
A few prerequisites for bode plot:
Laplace transform and network transfer function
Poles and zeros of transfer function
Break frequencies
Some useful rules for drawing high-order bode plots:
Decompose transfer function into first order terms.
Mark the break frequencies and represent them on the frequency axis the critical values for changes
Make bode plot for each of the first order term
For each first order term, keep the DC to the break frequency constant equal to the gain at DC
After the break frequency, the gain magnitude starts to increase or decrease with a slope of 20db/decade if the term is in the numerator or denominator
For phase plot, each first order term induces a 45 degrees of increase or decrease at the break frequency if the term is in the numerator or denominator
Consider frequencies like one-tenth and ten times the break frequency and approximate the phase by 0 and 90 degrees if the frequency is with the numerator (or 0 and -90 degrees if in the denominator)
Add all the first order terms for magnitude and phase response

4. Frequency response of RLC circuits
E.g. 1
E.g. 2
E.g. 3

5. The MOS Transistor
Polysilicon
Aluminum

6. The Gate Capacitance x L Polysilicon gate Top view Gate-bulk overlapd L
Polysilicon gate
Top view
Gate-bulk
overlap
Source n +
Drain W t ox n +
Cross section view L
Gate oxide

7. Gate Capacitance
Cut-off
Resistive
Saturation

8. Diffusion Capacitance
Channel-stop implant N 1 A
Side wall
Source W N D
Bottom x
Side wall j
Channel L S
Substrate N A

9. Frequency response of common source MOS amplifer
High-frequency MOS Small-signal
equivalent circuit
MOSFET common Source amplifier
Small-signal equivalent circuit for the MOS common source amplifier
Frequency response analysis shows that there are three break frequencies, and mainly the lowest one determines the upper half-power frequency, thus the -3db bandwidth

10. Exact frequency response of amplifiers
Exact frequency analysis of amplifier circuits is possible following the steps:
Draw small-signal equivalent circuit (replace each component in the amplifier with its small-signal circuit)
Write equations using voltage and current laws
Find the voltage gain as a ratio of polynomial of laplace variable s
Factor numerator and denominator of the polynomial to determine break frequencies
Draw bode plot to approximate the frequency response

11. Graphs from Prentice Hall
The Miller Effect
Consider the situation that an impedance is connected between input and output of an amplifier
The same current flows from (out) the top input terminal if an impedance is connected across the input terminals
The same current flows to (in) the top output terminal if an impedance is connected across the output terminal
This is know as Miller Effect
Two important notes to apply Miller Effect:
There should be a common terminal for input and output
The gain in the Miller Effect is the gain after connecting feedback impedance
Graphs from Prentice Hall

12. Application of Miller Effect
If the voltage gain magnitude is large (say larger than 10) compared to unity,
then
we can perform an approximate analysis by assuming is equal to
find the gain including loading effects of
use the gain to find out
Thus, using Miller Effect, gain calculation and frequency response characterization would be much simpler

13. Application of Miller Effect
If the feedback impedance is a capacitor ,then the Miller capacitance reflected across the input terminal is
Therefore, connecting a capacitance from the input to output is equivalent to connecting a capacitance
Due to Miller effect, a small feedback capacitance appears across the input terminals as a much larger equivalent capacitance with a large gain (e.g ). At high frequencies, this large capacitance has a low impedance that tends to short out the input signal

14. The model for low-frequency analysis
BJT small-signal models (for BJT amplifiers)
The model for low-frequency analysis
The model for high-frequency analysis
The base-spreading resistance for the base region (very small)
The dynamic resistance of the base emitter region
The feedback resistance from collector to base (very large)
Account for the upward slope of the output characteristic
The depletion capacitance of the collector-to-base region
The diffusion capacitance of the base-to-emitter junction
Note: in the following analysis of the CE, EF and CB amplifier in the next three slides, we will assume for simplicity (though they still appear in the small signal models).

15. Miller Effect: common emitter amplifier I

16. Miller Effect: common emitter amplifier II
Assume the current flowing through is very small compared to , then the gain will be considering the input terminal of the amplifier at b’ to ground.
Applying the miller effect for the amplifier, the following simplified circuit can be obtained:
Thus, the total capacitance from terminal b’ to ground is given as follows (neglect the miller capacitance from output terminal c to ground):
The break frequency, thus the -3db frequency is set by the RC lowpass filter (other voltage controlled current source, resistance does not contribute to the break frequency) is a main limiting factor for -3db bandwidth.

17. Emitter-follower amplifier
Using Miller Effect, we obtain the above equivalent circuit. If neglecting , It shows that the break frequency is

18. Common base amplifier
What about amplifier that do not have capacitance connected directly from output to the input?
For approximate analysis, we can neglect the simplified equivalent circuit can be shown in (c). Derive the transfer function for this circuit, it shows two break frequencies (with typical values, is approximately -3db bandwidth)

19. Fully-differential amplifierX X
To estimate the 3dB bandwidth of this one, note that the circuit if fully symmetric, so only the half circuit needs to be analyzed. The node voltage at X is 0 in small-signal analysis. Therefore we only need to analyze the right-hand side circuit, which is actually a common-emitter amplifier analyzed before. So the 3dB bandwidth of a common-emitter amplifier applies here.

20. Graphs from Prentice Hall
Cascode amplifier and differential amplifier
The cascode amplifier can be viewed as a common-emitter amplifier with a common-base amplifier.
Due to low input impedance of Q2, the voltage gain of Q1 is small. So, Miller effect on Q1 is small.
The Emitter-coupled differential amplifier can be viewed as a emitter-follower amplifier cascaded with a common-base amplifier (both have wider bandwidth than common-emitter amplifier).
Graphs from Prentice Hall