1. General Approach of Haemostasis
Lecture 3:
Coagulation Time of whole blood

2. Coagulation Time ( Clotting Time) CT.
Clotting Time is the time required for blood to form a clot in vitro.
The basis for the test is that whole blood will form a solid clot when exposed to a foreign surface such as a glass tube.
It is a rough measure of all intrinsic clotting factors in the absence of tissue factors. Variations are wide and the test sensitivity is limited.
As the test is the least effective test in the diagnosis of actual haemostasis failure, it has been replaced by PTT.
Clotting time was used as a screening test to measure all stages in the intrinsic coagulation system and to monitor heparin therapy .
Clotting is the formation of a jelly like substance over the valves of the vessels.

3. It is a complex process involving over 30 substances
It is however, a time-consuming test, has poor reproducibility, is sensitive only extreme factor deficiencies. It is therefore, of limited use in today’s laboratory .
It is a complex process involving over 30 substances
Conditions accompanied by increased Clotting Time:
Factors V, VII, VIII, IX, XI, XII Deficiencies.
Hemorrhagic disease of Newborn
Vitamin K deficiency.
Heparin Therapy.
Presence of Circulating antibodies (inhibitors)
Anemia and leukemia.
Afibinogenemia and Pneumonia.
and heparin.
Reproducibility is the ability of an experiment or study to be accurately reproduced, or replicated, by someone else working independently. It is one of the main principles of the scientific method.
Heparin: Works by markedly enhancing activity of antithrombin, which inhibits activated factors II, IX, X, XI, XII, kallikrein and probably VII, but doesn’t cause a true decrease in factor levels
Vitamin K: prothrombin (factor II), factors VII, IX, X, protein C, protein S, and protein Z

4. Methods:
Capillary Method.
Slide Method.
Tube Method.

5. Tube Method (Lee-White method)
Reagent & equipment
Water bath, 37O C.
Glass test tube (10 x 75 mm)
Stopwatch.
Plastic syringe and 20-gauge needle.
Specimen
Fresh whole blood , 4 ml .
Etymology: Roger I. Lee, American physician, b. 1881; Paul D. White, American physician, ; Gk, meta, beyond, hodos, way
a method of determining the length of time required for a clot to form in a test tube of venous blood. It is not specific for any coagulation disorder but is often used to monitor coagulation during heparin therapy. Because normal values and precise methodology vary, instructions are provided by most laboratories.

6. Procedure
Label 3 glass test tube with patient name and number them, 1, 2, and 3.
Perform a clean, Untraumatic venipucture using a 20-gauge needle and drawn 4 mL of blood.
Remove the needle from the syringe, and fill each of the three tubes with 1 ml blood.
The last 1 ml of blood may be discarded.
Start the stopwatch as soon as the blood enters the syringe.
Place the three test tubes in a 37°C water bath.
At exactly 3 min., Remove the first tube form water bath and tilt gently to a 45° angle to see whether the blood has clotted.
If Blood not clotted return it to the water bath and examine it at 30 second intervals.

7. Normal Range: 5 – 12 Minutes***
After the blood in the first tube has clotted, examine the second tube immediately.
Then examine the 3rd one.
Record the time it took the blood in the 3rd test tube to clot.
Normal Range: 5 – 12 Minutes***
Since agitation and handling speed up coagulation, the clotting time test tube #3 is the reported result.

8. Discussion
Poor venipucture technique, causing hemolysis or tissue thromboplastin to mix with the blood, shortens the clotting time.
Bubbles entering the syringe when the blood sample is being obtained increase the rate of coagulation.
Always tilt the tube in the same direction and at the same angle so that the blood is moving in the same pathway up the side of the tube each time.
Excessive agitation of blood (occur during the transfer of the blood from the syringe to the test tube). The blood should be allowed to flow gently down the inside of the test tube and not forcefully squirted into the test tube.

9. Dirty Test Tubes will affect the result.
At the completion of the clotting time, one tube should remain in the 37°C water bath to be checked for clot retraction. Also, this same tube may be allowed to remain in the water bath overnight and checked the next day for clot lysis.
Dirty Test Tubes will affect the result.
Coagulation will be retarded by the following:
Temperature Below 35O C.
Temperature above 45O C.
Diameter of the test tube (the smaller the diameter, the more rapid the clot formation is).

10. ACT (Activated clotting Time)
Fresh whole blood is added to a tube containing negatively charged particles and timed for the formation of a clot.
The type of negatively charged particle affects the "normal" length of ACT
Celite = Diatomaceous Earth: normal is seconds
Kaolin: normal is seconds
Glass particles: normal seconds
Type of machine affects normal and therapeutic values
Daily calibration checks are imperativee
Therapeutic Range: seconds.
Diatomaceous Earth also known as diatomite or kieselgur, is a naturally occurring, soft, siliceous sedimentary rock that is easily crumbled into a fine white to off-white powder. The typical chemical composition of oven dried diatomaceous earth is 80 to 90% silica, with 2 to 4% alumina (attributed mostly to clay minerals) and 0.5 to 2% iron oxide.
Kaolin It is a layered silicate mineral, with one tetrahedral sheet linked through oxygen atoms to one octahedral sheet of alumina octahedra.[4] Rocks that are rich in kaolinite are known as china clay, white clay, or kaolin.

11. Hemochron® Tests measured
Heparin monitoring with or without Aprotinin.
Sample and volume requirements
Fresh whole blood- 2mL. Elite: 200µL to fill cuvette well.
Controls
Electronic QC
Liquid quality control- normal and abnormal
Reference Ranges
Normal range- healthy donors
RFTCA 510 tubes: 105 – 167 seconds
FTK-ACT tubes: 91 – 151 seconds
Normal range- cardiopulmonary bypass patients
HRFTCA 510 tubes: seconds
FTK-ACT tubes: seconds
Hemochron : A warmed test tube is rotated inside the machine. As the blood clots, it displaces the magnet within the test tube. The clotting time is determined when the magnet has displaced enough to activate a proximity switch
Medtronic HemoTec: A mechanical plunger is dipped in and out of a kaolin activated blood sample. The machine optically senses the time it takes the plunger to move through the specimen. Clotting is defined by the "drop time" threshold for the plunger
The machines do not correlate with one another but in general the times for the Hemochron are 30% greater than the Medtronic HemoTec

13. Clotting Time - Capillary method
Material
Sterile disposable pricking needle or lancet.
Stop watch
Dry glass capillary tube (narrow diameter top 2 mm, minimum 10 cm long.)
Cotton Swab of absorbent cotton.
Spirit wetted, cotton swab.
70 % v/v ethyl alcohol
Capillary action is the movement of a liquid into a tube based on its surface tension.

14. PROCEDURE
Apply alcoholic 70 % v/v to the clean finger with cotton swab. Allow it to dry naturally.
Prick the finger with usual aseptic precautions. Remove the first drop.
Dip one end of the capillary into blood drop gently without pressure. (use 3-4 capillary tubes)
The Timer is started when the first blood start to enter the first capillary tube.
Allow to fill the capillary with blood by lowering the end of fitted capillary. (Do not suck the blood) around ¾th of its length undipped.
After every 30 seconds, using stopwatch, break a small piece of capillary.
Repeat breaking at regular time intervals, till fibrin thread appears at the broken end of capillary tube. Do not pull away the cut pieces ling apart and bristly.
Record time interval between pricking finger and first appearance of fibrin thread at the broken ends of capillary tube. That is clotting time of blood.
Don't forget to dispose of the broken tube in the SHARPS CONTAINER.

15. Clotting time of whole blood

16. Clotting Time - Slide Method
The surface of the glass tube initiates the clotting process. This test is sensitive to the factors involved in the intrinsic pathway
The expected range for clotting time is 4-10 min.

17. Clot retraction (Obsolete test)
This test measures the amount of time it takes for a blood clot to pull away from the walls of a test tube (Shrinking).
The edges of the blood vessel wall at the point of injury are slowly brought together again to repair the damage.
It is used to evaluate and manage blood platelet disorders, including Glanzmann's thrombasthenia
So Clot retraction depends primarily on the number and activity of the blood platelets.
This test is reliable only when the concentration of fibrinogen within normal limits.
Normally a blood clot will begin to retract from the walls of the tube and express serum within one hour.

18. Glanzmann's thrombasthenia
Is an abnormality of the platelets
It is an extremely rare coagulopathy in which the platelets lack glycoprotein IIb/IIIa.
Reduced glycoprotein IIb/IIIa causes reduced platelet aggregation and clot retraction - no fibrinogen bridging can occur, and bleeding time is significantly prolonged);
Glycoprotein IIb/IIIa is an aggregation receptor expressed by thrombocytes. This receptor is activated when the thrombocyte is stimulated by ADP, epinephrine, collagen and thrombin. The GpIIb/IIIa integrin is essential to the blood coagulation since it has the ability to bind fibrinogen, fibronectin and vitronectin. Glycoprotein Ib enables the platelet to be activated by contact with the collagen-von Willebrand-complex that is exposed when the endothelial blood vessel lining is damaged and then aggregate with other thrombocytes via fibrinogen.
Glanzmann's thrombasthenia can be inherited in an autosomal recessive manner[2] or acquired as an autoimmune disorder.[3]

19. Clot retraction test
This is a measure of platelet function. The test is done in blood to which no anticoagulant has been added and is allowed to clot. Clot retraction is then looked for.
Clot retraction becomes abnormal in conditions like
Fibrinogen deficiency (congenital or acquired)
Thrombocytopenia < 1ooooo
Thrombosthenia
Polycythaemia
Reduced clot formation: Glanzmann thrombasthenia , DIC, hypofibrinogenemia, dysfibrinogenemia (small clot with increased red blood cell “fall-out”)
Disseminated intravascular coagulation (DIC) is a serious disorder in which the proteins that control blood clotting become abnormally active.

20. Procedure
Obtain 2 ml of blood by venipucture. Place one ml in a glass test tube in a 37oC water bath.
Inspect clot at 1, 2, 4 and 24 hours after clotting. Observe for retraction, quality, and lysis of the clot.
Remaining 40-60% consists of serum and red blood cell “fall-out” from clot
A visual examination of the clot is made. Usually the clot retracts and expresses serum within two hours.

21. Interpretation of results
The clot will retract from the walls of the tube until the red cell mass occupies 50% of the total volume of blood in the tube
There is a variable degree of retraction or there is no retraction at all. Grades as follows:
0 : no serum extruded
1+ : 5-10% serum extruded
2+ : 10-20% serum extruded
3+ : 20-35% serum extruded
4+ : 35-50% serum extruded
Results are reported as the length of time it took for the clot to retract
2-4 hrs is reported as normal
After 4 hrs is reported as poor
After 24 hrs is reported as no retraction

22. Clot lysis test
The whole blood clot lysis time is used to detect increase fibrinolysis
This test is only able to detect high increase in fibrinolytic activity
Clot lysis testing is a measure of the presence of the clot after 24 hours (blood fibrinolysis).

23. Procedure
At the completion of the clotting time one tube should remain in the 37 water bath
A second tube is placed in the refrigerator as soon as clotted as a control
The tube is test for the disappearance of clot after 4, 8 and 24 hrs
If the sample becomes fluid in less than 48 hrs , the blood is poured out onto a piece of filter paper to be sure for clot disappearance

24. Interpretation
The disappearance of clot before 48 hrs means increase fibrinolysis
After 48 hrs clot may be
Comment
Refrigerated tube
37 C tube
Low fibrinogen
Disappear
Abnormal fibrinolysis
(No clot lysis after 48 hrs)
Still intact
Nomal fibrinolysis

25. Euglobulin Clot Lysis Time
Activity
What is the test mentioned below and how w we can do it?.
Euglobulin Clot Lysis Time

26. Thank you
Next Lecture: Prothrombin Time (PT)