Presentation is loading. Please wait.

Presentation is loading. Please wait.

Model 095-096 DISASSEMBLY AND ASSEMBLY 1- Disassembly To replace the spring (11), or clean any of the internal components of the valve, proceed in the.

Published bySamson Gray Modified over 9 years ago

Similar presentations

Presentation on theme: "Model 095-096 DISASSEMBLY AND ASSEMBLY 1- Disassembly To replace the spring (11), or clean any of the internal components of the valve, proceed in the."— Presentation transcript:

1

2 Model 095-096 DISASSEMBLY AND ASSEMBLY 1- Disassembly To replace the spring (11), or clean any of the internal components of the valve, proceed in the following manner: A- Withdraw the clip (20), using a punching tool, and lift the lever (19). B- Unscrew the cap (2) and remove. C- Holding the rod (16) (17) steady, loosen the hollow screw nut (8), until the constructive limit, and the hollow screw (7) until you note a releasing of the spring (11). D- Unscrew the body (1) holding the rod (16) (17) and the seat (13) (14) steady. E- Lift the body (1) and you will have acces to all the components.

3 Model 095-096 2- Assembly A- Enter the body (1) and the joint (15) through the upper part the rod (16) (17). B- Turn the body (1) holding the rod (16) (17) and the seat (13) (14) steady. C- Replace the hollow screw (7) with the hollow secrew nut (8). D- Adjust the set pressure with the hollow screw (7) and fix the adjustment position with the hollow screw nut (8). E- Change the coupling (18) and lightly tighten the cap (2). F- Place the lever (19) and fix it with the clip (20). ADJUSTING THE SET PRESSURE A- Proceed according to DISASSEMBLY A, B, C. B- Proceed according to ASSEMBLY D, E, F.

4

Download ppt "Model 095-096 DISASSEMBLY AND ASSEMBLY 1- Disassembly To replace the spring (11), or clean any of the internal components of the valve, proceed in the."

Similar presentations

Instructions for making plunger fork tool. Drawing for the trigger assembly.

Instructions for making plunger fork tool. Drawing for the trigger assembly.
ZIPP 404 BEARING REPLACMENT GUIDE Tools Needed:

ZIPP 404 BEARING REPLACMENT GUIDE Tools Needed:
Rework Procedure for Wash Motor Pulley Change Model : Rosa & Rosa Plus Part Details & Tools required Sr NoPart DescriptionQtyTool used to replace old artworks.

Rework Procedure for Wash Motor Pulley Change Model : Rosa & Rosa Plus Part Details & Tools required Sr NoPart DescriptionQtyTool used to replace old artworks.
40-200 ¾”-2”. Modification Overview  Production of the 40-200 series began in 1989 and is current.  Early models of ¾”-2” 40-200 series did not always.

¾”-2”. Modification Overview  Production of the series began in 1989 and is current.  Early models of ¾”-2” series did not always.
Model 695AV 1. Dissasembly To replace the spring, or clean any of the internal components of the valve, proceed in the following manner: A.Cut the seal.

Model 695AV 1. Dissasembly To replace the spring, or clean any of the internal components of the valve, proceed in the following manner: A.Cut the seal.
Blackwood Fire Company Stihl Chainsaw Maintenance.

Blackwood Fire Company Stihl Chainsaw Maintenance.
Head jig usage procedure RKC London Office. Set the head jig 2) Put two screws with loose condition 3) Lock the plate 4) Tighten two head jig screws 5)

Head jig usage procedure RKC London Office. Set the head jig 2) Put two screws with loose condition 3) Lock the plate 4) Tighten two head jig screws 5)
Model 495/496 EP Full lift safety valve with spring loading (AIT) model 495/496 - EP. 1. Disassembly and assembly. 1.1 Disassembly. To replace the spring,

Model 495/496 EP Full lift safety valve with spring loading (AIT) model 495/496 - EP. 1. Disassembly and assembly. 1.1 Disassembly. To replace the spring,
860 (LF), 880 ½”- 2” 860 (LF), 880 ½”- 2”. Modification Overview  Production of the ½ - 2” 860 series began in 1997 and is current.  The 880 is an “N”

860 (LF), 880 ½”- 2” 860 (LF), 880 ½”- 2”. Modification Overview  Production of the ½ - 2” 860 series began in 1997 and is current.  The 880 is an “N”
860 21/2”-10”. Modification Overview  Production of the 2½” – 10 sizes began in 1993.  Lead free version (LF860) was introduced in 2011. Parts do not.

860 21/2”-10”. Modification Overview  Production of the 2½” – 10 sizes began in  Lead free version (LF860) was introduced in Parts do not.
Model 995 EP DISSASSEMBLY AND ASSEMBLY 1.Disassembly To replace the spring or clean any internal components of the valve, proceed in the following manner:

Model 995 EP DISSASSEMBLY AND ASSEMBLY 1.Disassembly To replace the spring or clean any internal components of the valve, proceed in the following manner:
Model 895 AP DISSASSEMBLY AND ASSEMBLY 1.Disassembly To replace the spring or clean any internal components of the valve, proceed in the following manner:

Model 895 AP DISSASSEMBLY AND ASSEMBLY 1.Disassembly To replace the spring or clean any internal components of the valve, proceed in the following manner:
994 RPDA 21/2”- 6”. Modification Overview  Production of the 994RPDA began in 1999 and is current.  The 994 RPDA currently utilizes the ¾” 009M3 for.

994 RPDA 21/2”- 6”. Modification Overview  Production of the 994RPDA began in 1999 and is current.  The 994 RPDA currently utilizes the ¾” 009M3 for.
Model 495/496 AP and CP Full lift safety valve with spring loading (AIT) model 495/496 - AP and CP. 1. Disassembly and assembly. 1.1 Disassembly. To replace.

Model 495/496 AP and CP Full lift safety valve with spring loading (AIT) model 495/496 - AP and CP. 1. Disassembly and assembly. 1.1 Disassembly. To replace.
CHAPTER 33 Drum Brake Systems.

CHAPTER 33 Drum Brake Systems.
March 19, 2013 4” Leg Valve Changeout. Required Tools and Materials 3” Wrench 9/16” Wrench 11/16 Wrench Seal Pick Clean hydraulic fluid.

March 19, ” Leg Valve Changeout. Required Tools and Materials 3” Wrench 9/16” Wrench 11/16 Wrench Seal Pick Clean hydraulic fluid.
825, 825Y, 825YD 21/2”-10”. Modification Overview  825- (1975-1988) Cast iron body- Threaded in seats- Internal check parts are epoxy coated iron. Old.

825, 825Y, 825YD 21/2”-10”. Modification Overview  825- ( ) Cast iron body- Threaded in seats- Internal check parts are epoxy coated iron. Old.
975, 975XL ¾”-2” 975, 975XL ¾”-2”. Modification Overview  Production of the original 975 began in 1990. This version had buna-n check discs and did not.

975, 975XL ¾”-2” 975, 975XL ¾”-2”. Modification Overview  Production of the original 975 began in This version had buna-n check discs and did not.
975DA 2½”-10”. Modification Overview  Production of the 975DA began in 1993 and was discontinued in 2004.  The 975DA uses a ¾” 975XL for the bypass.

975DA 2½”-10”. Modification Overview  Production of the 975DA began in 1993 and was discontinued in  The 975DA uses a ¾” 975XL for the bypass.
994 2½ ”- 10”. Modification Overview  Production for the 994 began in 1999 and is current.

994 2½ ”- 10”. Modification Overview  Production for the 994 began in 1999 and is current.

Similar presentations

Ads by Google