1. Response Spectrum Analysis as per Indian IS: 1893 (Part 1)-2002
Dynamic Analysis
PART 2

2. Methodology Qik = Ak*fik*Pk*Wi
The design lateral shear force at each floor in each mode is computed by STAAD in accordance with the IS: 1893 (Part 1) -2002
(equation c and d.)
User Input
Qik = Ak*fik*Pk*Wi
User Input

3. STAAD utilizes the following procedure to generate the lateral seismic loads.
User provides the value for   𝑍 2 x 𝐼 𝑅 as factors for input spectrum
Program calculates time periods for first six modes or as specified by the user.
Program calculates Sa/g for each mode utilizing time period and damping for each mode.
STAAD utilizes the following procedure to generate the lateral seismic loads.
User provides the value for  as factors for input spectrum
Program calculates time periods for first six modes or as specified by the user.
Program calculates Sa/g for each mode utilizing time period and damping for each mode.
The program calculates design horizontal acceleration spectrum Ak for different modes.
The program then calculates mode participation factor for different modes.
The peak lateral seismic force at each floor in each mode is calculated.
All response quantities for each mode are calculated.
The peak response quantities are then combined as per method (CQC or SRSS or ABS or TEN or CSM) as defined by the user to get the final results.
for

4. The program calculates design horizontal acceleration spectrum Ak for different modes.
The program then calculates mode participation factor for different modes.
The peak lateral seismic force at each floor in each mode is calculated.
All response quantities for each mode are calculated.
The peak response quantities are then combined as per method (CQC or SRSS or ABS or TEN or CSM) as defined by the user to get the final results.

5. The design base shear VB (calculated from the Response Spectrum method) is compared with the base shear Vb (calculated by empirical formula for the fundamental time period).
If VB is less than Vb, all of the response quantities are multiplied by Vb /VB as per Clause
The design base shear VB (calculated from the Response Spectrum method) is compared with the base shear Vb (calculated by empirical formula for the fundamental time period).
If VB is less than Vb, all of the response quantities are multiplied by Vb /VB as per Clause  
To have STAAD compute the empirical base shear Vb, please enter the data described in Section and place that data before the first load case in the STAAD input. STAAD does not calculate the fundamental frequency of the structure needed for the empirical base shear Vb. calculation; so you must enter either the ST parameter or the PX and PZ parameters in the Section DEFINE  1893  LOAD data.

6. How STAAD Calculates of Base Shear in RS Analysis
The base shear, for a given mode for a given direction, reported in the response spectrum analysis is obtained as
VB = X*Y*Z*D
where
X = Mass participation factor for that mode for that direction
Y = Total mass specified for that direction
Z = Spectral acceleration for that mode
D = direction factor specified in that load case

7. BMD for RS Load Case
The member forces are computed correctly only at the 2 ends of the member.
The sign of these forces cannot be determined because the method used to combine the contribution of modes cancels the signs.
Force values do not necessarily occur at the same instant of time.
STAAD plots a straight line joining the max. bending moment values at start and end joints of member, absolute (positive) values.

8. What is the Scale Factor to be provided when specifying a Response Spectra?
Spectrum data consists of pairs of values which are Period vs. Accn. or Period vs. Displacement.
The acceleration or displacement values obtained for that site may have been provided to you as normalized values or un-normalized values.
Normalization means that the values of acceleration or displacement have been divided by a normalization factor.
One of the commonly used normalization factors is 'g', the acceleration due to gravity.

9. If the spectrum data you specified is normalized, provide the NORMALIZATION FACTOR as the SCALE FACTOR.
If your spectrum data is un-normalized, there is no need to provide a scale factor. Default value of one will be used then.
Make sure that the value you provide for the SCALE FACTOR is matching the length units you have specified. So if the scale factor is 'g‘ and length is in meter, provide value 9.81 ~ 10.
STAAD will multiply the spectral acceleration or spectral displacement values by the scale factor.

10. Direction Factor
The Direction factor is value by which the spectral displacement for associated direction is multiplied.
SPECTRUM SRSS X 0.7 Y 0.5 Z 0.65 DISP DAMP 0.05 SCALE 32.2
Period is determined for each mode.
Spectral displacement (Sa/g) for that mode is read by interpolating the response spectrum plot.
Spectral displacement “Sa/g" for each direction is multiplied with associated Direction factor. D

11. The X direction spectral displacement = “Sa/g" * 0.1822
The Y direction spectral displacement = “Sa/g" * 0.5
The Z direction spectral displacement = “Sa/g" * 0.65

12. How to obtain critical value from the design standpoint?
Create 2 load combination cases for every spectrum case. For example, if the dead load case is 1, and the spectrum load case is 2, you could create
LOAD COMB 3
LOAD COMB 4
Use the critical value from amongst these 2 load combination cases for design purposes.
Thus considering a positive effect as well as the negative effect of the spectrum load case.

13. Obtain vertical distribution of the total base shear in a RS analysis, like in Static Procedure.
No direct method to obtain lateral force distribution. Since the values from a RS analysis are absolute quantities.
We may add up the shears in the columns above that level for an approximate estimate.

14. Global Reaction doesnot equals Global Base Shear.
Suppose we have two modes and 4 supports in the x direction & in SRSS combination method the results are computed as follows:

15. Note that SRSS base shear (39
Note that SRSS base shear (39.8) does not equal the sum of the SRSS reactions ( =96.2).
This is due to the fact that the individual maximums would not occur at the same time and not necessarily with the same sign. So the base shear magnitude is usually much less than the sum of the reactions.