1. Review of Relative Density Principles v Relative Density principles apply to compaction of relatively clean, coarse- grained soils. v Relatively clean usually taken to be less 12 % or less finer than the #200 sieve. v Important for compaction study of filters

2. Objectives v Explain basic principles of compacting clean sands and gravels v Understand basic tests to obtain reference densities. v Use 1 point compaction test in design and quality control v Summarize minimum and maximum index density tests v Detail the importance of water content in compacting clean sands and gravels

3. Review of Compaction Principles v Compaction Tests are not commonly performed on soils with 12 % or fewer fines v Small percentage of fines means soils cannot easily hold water to examine range of water and effect on dry density

4. Review of Compaction Principles v Compaction tests performed on clean sands may have this appearance Dr density w %

5. Compacting Clean Sands v Clean sands are compacted most easily at either very dry or very wet water contents v At intermediate water contents, capillary stresses in voids resist compaction v Bulking is term for this phenomenon

6. Compacting Clean Sands v Vibration most effective energy for sands v Use smooth-wheeled vibratory roller

7. Relative Density v Alternative to traditional compaction test is relative density tests v Minimum Index Density v Maximum Index Density v Relative Density

8. Minimum Index Density v Minimum index density of clean sand is that resulting from very loosely filling a steel mold. ASTM Method D4254 Sand dropped no more than 1”

9. Minimum Index Density v After filling the mold, excess soil is carefully screed off. The volume of this mold is 0.1 ft 3. v After filling the mold, excess soil is carefully screed off. The volume of this mold is 0.1 ft 3. Knowing the weight of soil in the mold, the dry density is easily computed

10. Maximum Index Density v Example Minimum dry density = 96 pcf v Maximum index density of clean sand results from vibration at high amplitude on vibratory table for 10 minutes. ASTM D4253 v Example Maximum dry density = 117.5 pcf

11. Maximum Index Density Vibratory table Weight on sample inside sleeve

12. Maximum Index Density Vibratory table Weight on sample inside sleeve

13. Maximum Index Density Sample densified by vibration Measure  height to determine new  d Plate on which weight sits during vibration

14. Void Ratio and Dry Density v The void Ratio is calculated for each state of denseness of sample.  Maximum void ratio occurs at minimum index density - For Example Min.  d = 96.0 pcf  Minimum void ratio occurs at maximum index density For Example Maximum  d = 110.0 pcf

15.  First Calculate void ratio at Minimum  d Minimum and Maximum Void Ratios  Next Calculate void ratio at Maximum  d

16. e max e min e measured  dmax  d min  d measured Diagram below illustrates a relative density of about 40 % increasing density Relative Density Equation

17. v Now, assume that the density of this sand was measured in a compacted fill and it was 102.5 pcf. Calculate a value for relative density of the fill. First, calculate the void ratio of the fill: Calculate Void Ratio of Compacted Sand

18. v Now, use the values of void ratio in the relative density equation: Compute Relative Density

19.  v Relative Density Equation (rewritten in dry density terms) v Solve for Example:

20. Fort Worth Relative Density Study v NRCS lab in Fort Worth studied 28 filter sands and used some published data v Minimum and Maximum Index Densities were performed on each sample v A 1 point dry Standard Proctor energy mold was also prepared for each sample. v Values of 50% and 70% relative density were plotted against the 1 point Proctor value

21. 70 % Relative Density vs. 1 Point Proctor

22. v Conclusion is that the field 1 point Proctor dry test is about equal to 70 % relative density 70 % Relative Density vs. 1 Point Proctor

23. 50 % Relative Density vs. 1 Point Proctor

24. v Conclusion is that the 95 % of the field 1 point Proctor dry test is about equal to 50 % relative density 50 % Relative Density vs. 1 Point Proctor

25.  D 70 = 1.075 x  d 1pt -9.61, for RD 70 and  d 1pt in lb/ft3  D 50 = 1.07 x  d 1pt - 12.5, for RD 50 and  d 1pt in lb/ft 3 Relative Density Estimates from FW SML Study

26. v Example Relative Density Estimates –Given: 1 Point Proctor Test  d = 105.5 pcf –Estimate 70 % and 50% Relative Density –Given that measured  d is 98.7, evaluate state of compaction of sand. Relative Density Estimates from FW SML Study

27. v Class Problem - Relative Density –A soil’s minimum index density is 96.5 pcf and its maximum index density is 111.5 pcf. The Gs value is 2.65 –Calculate the e min and e max –Compute the void ratio and dry density corresponding to a relative density value of 70 % Review of Relative Density

28. v Given: Minimum index density is 96.5 pcf v Maximum index density is 111.5 pcf. Class Problem Solution

29. v Now, substitue a value for RD of 70(%) in the relative density equation Class Problem Solution

30. v Solving and Rearranging the equation: Class Problem Solution

31. v Now, calculate a value for dry density at this void ratio: Class Problem Solution v Summary - The dry density corresponding to 70(%) relative density for this sample is 106.5 pcf

32. Other information on Relative Density

33. Chart is for silty sands (SM) Other information on Relative Density

34. Class Problem v Given that the water content of a silty sand that was obtained from a saturated zone of a channel bank measured 24.5 percent v What is the estimated relative density of the sand?

35. Class Problem Solution v Reading from the chart, the estimated Rd value is about 42 percent.