1. MICE Fiber Tracker Electronics AFEII for MICE (Front end readout board) Recall: AFEs mount on ether side of the VLPC cass, with fibers going to the VLPCs between them. AFE has 8 identical modules Each module reads 64ch of VLPCs AFEs functions: fast discr (1bit/ch) send to L1 trigger system. If the event looks interesting (to the L1 system!), the AFE can “remember” Q from ~4uS earlier and digitize it for readout Much slower than the discriminators!

2. MICE Fiber Tracker Electronics AFEII for MICE Digital readout vs. Analog readout AFEII two readout paths Digital: Discriminators go over LVDS links More details later Analog: Zero suppressed data from ADCs (addr/data pairs) over a custom parallel link (a.k.a. gray cable) More details later

3. MICE Fiber Tracker Electronics AFEII for MICE AFEII designed for Tevatron not MICE! AFEII two readout paths: L1: 512 discriminator bits/board/132ns L2: (only after an “L1 accept”) reads out ADC 8bits/ch x 512ch (zero supressed) AFEII designed for ~10Khz L1 accept rate at ~5% deadtime => 10uS per event time budget

4. MICE Fiber Tracker Electronics AFEII for MICE Fiber tracker: why analog at all? Better quality data ADCs data can be corrected for common mode ADCs can correct for ch-to-ch variation But watch out for zero supression! For Dzero, can use to improve resolution

5. MICE Fiber Tracker Electronics AFEII for MICE Digital readout details: LVDS here means a specific chip set from TI SN65LVDS95 (running @ 53Mhz) 20 bits + 1 “frame” bit sent over 4 UTP pairs (3 signal + clock) @ 53 * 7 = 371 Mhz Frame bit sent once every 7 * 18.8ns = 132ns 4 LVDS links/board = 1/pair of modules (10bits per module) Data rate = 53Mhz * 20 * 4 = 4.24 Gbps

6. MICE Fiber Tracker Electronics AFEII for MICE Analog readout details: Custom bi-directional parallel link between the Sequencer and the AFE 8 data bits + data valid per AFE Max data rate = 53 * 8 = 424 Mbps Digitization: 2 dual ADCs/64 ch module=16 ch/ADC ADC runs @ max 10Mhz => 16 * 100ns = 1.6uS Tot: ~2us + ~40ns / hit ch= ~21us max

7. MICE Fiber Tracker Electronics Mice beam structure ~600 muons in 850 uS Long enough between pulses =  for DAQ Analog readout: depends on occupancy If FULL readout, can do about ~40 during spill Digital readout: can keep up Still not 100% live time: need resets AFEII for MICE us

8. MICE Fiber Tracker Electronics Mice readout Analog readout for MICE Two options: 1.the full Dzero system -Sequncer (SEQ) and sequencer controller (SEQC) (and crate! 9U custom backplane…) - VME Receiver Buffer (VRB) and VRB controller (VRBC) (and another 9U crate!) - must talk to SEQ/SEQC/VRB/VRBC so need 1553 interface as well AFEII for MICE

9. MICE Fiber Tracker Electronics Mice readout (cont.) Analog readout for MICE Two options: 2.the StandAlone Sequencer (SASeq) +used in the MICE cosmic test -rather slow… AFEII for MICE

10. MICE Fiber Tracker Electronics Analog readout for MICE + tons of experience from Dzero + AFEII designed to work this way + know how to trigger, sync board to board, etc. - need time to digitize! ~ maybe beam structure can be chosen to make this mode work better? 600mu/1ms => 600KHz L1 accept rate! AFEII for MICE

11. MICE Fiber Tracker Electronics Mice readout Digital readout for MICE + fast + very simple - need a receiver… more detail below - no detailed analog info ~ not for use with AFEII-t (not a problem!) AFEII for MICE

12. MICE Fiber Tracker Electronics Digital readout for MICE Need a new board! Receive LVDS, store into FIFO, interface to VME But How to get clock to boards? How to get trigger to board? Can still use the gray cable! (w/SASeq) AFEII for MICE

13. MICE Fiber Tracker Electronics Need new board Very simple 6U VME Should be easy to design and build! Cost=$1K/board 1 board/AFE AFEII for MICE FPGA LVDS VME I/F SRAM

14. MICE Fiber Tracker Electronics Hybrid option On the AFEII, there is a path from FPGA to LVDS Can readout analog information via LVDS Still need the digitize time =~1.6 to 2 us But can readout as fast as digitize AFEII for MICE

15. MICE Fiber Tracker Electronics Analog readout Maybe 40 events/pulse (if 850uS pulse!) Digital readout Trade live time vs. overlaps (2K events/pulse) Min integration window ~50ns, max=anything! Reset time ~40ns Need to design and build a new board! Not really an option for MICE since MICE will use AFE IIt Time stamp for hits – TAC – need analog output Hybrid readout ADC thru LVDS (400 events/pulse) Still need the new board! AFEII for MICE summary

16. MICE Fiber Tracker Electronics AFE II for MICE D0 is starting work on an ADC  LVDS interface board This will likely work for MICE and be the preferred readout Data rates exceeding 600 muons/sec are therefore possible with 3 Hz RF 3 Hz is appears to be doable and for DAQ considerations is preferred over 1 Hz operation