1. Specification section 3.3
Joining methods (temporary):
knock down fittings
Specification section
3.3

2. 3.3 Joining methods (temporary): Knock down fittings
What you need to learn
The advantages and disadvantages of using the various knock down fittings when joining materials and components.

3. 3.3 Joining methods (temporary): Knock down fittings
What are knock down fittings?
Knock-down fittings are those that can be put together easily, normally using only a screw driver, a drill, a mallet/hammer, Allen key and other basic tools. They are temporary joints although many are used to permanently join together items such as cabinets and other pieces of furniture that are purchased in a flat pack.
They are known as ‘component parts.’

4. 3.3 Joining methods (temporary): Knock down fittings
The different types of fittings
Screws
Hinges
Dowel joint
Barrel nut and bolt
Cam fitting
T nut and bolt
Corner plate
Chipboard fastener
Block connector

5. 3.3 Joining methods (temporary): Knock down fittings
Screws
Countersunk head machine screws, also called set screws.
When using screws, you will need to drill a pilot hole before screwing the screw into the material. This helps to guide the screw into place, but it must not be so big that the thread doesn’t grip to the material.
Set screws are also called machine screws. They have a
thread that goes right up to the head.
Self tapping screws are made of hardened steel and cut their
own thread as they are screwed in. A tapping size hole equal to the
core diameter of the screw should be drilled before the screw is
inserted. They are used for joining thin sheets of metal and plastics.
This shows a screw used as a knock-down fitting.

6. 3.3 Joining methods (temporary): Knock down fittings
Hinges
Hinges are flexible joining fittings and can be made from steel, brass or nylon.
Concealed hinges are strong spring loaded hinges that can be adjusted once the hinge has been fitted. They are often used on wardrobe and kitchen cabinet doors.
Butt hinges are usually let into the edges of doors and frames so that they are almost hidden from view when the door is shut. Cupboard and room doors, lids of small boxes and windows.
Piano hinges are long butt hinges. They allow the screw
holes to be spread along the whole surface of the door to give extra holding power. This is useful when attaching hinges to edges of man made boards. Piano hinges can be cut with a hacksaw to the required length. They can be used on pianos and box and furniture lids.

7. 3.3 Joining methods (temporary): Knock down fittings
Dowel joint
The dowel joint is basically the same as a butt joint except dowels are used to hold the two pieces of wood together instead of screws and nails
It is important that the holes are aligned correctly otherwise the joint will not be square.
You can leave the joints so that they are not glued if you wanted to take them apart or glue will make the joint stronger but also permanent. By using dowels that have indents, it increases the gluing area. They are not a knock-down fitting if you glue it.
If used as a knock down fitting you would also use a screw.

8. 3.3 Joining methods (temporary): Knock down fittings
Barrel nut and bolt
The nut is placed in the wood with the hole in it facing the bolt. The nut has a thread inside it.
When you do up the screw the end of it will find the hole in the nut. You keep the nut in place with a flat-headed screw driver.

9. 3.3 Joining methods (temporary): Knock down fittings
Cam fitting
Use a Philips head screw driver to turn the cam fixture once the plug is in place and the wood has butted together. This will lock the plug in place.
You will need to line the plug with the cam fixture.
These type of fixtures can be undone.

10. 3.3 Joining methods (temporary): Knock down fittings
T nut and bolt
As the bolt is done up, the t nut grips into the wood. As there are three prongs on the nut, it stops the bolt from undoing.
T nut

11. 3.3 Joining methods (temporary): Knock down fittings
Corner plate
Wing nut
Screw
Screw
The two screws connect the plate to the side. The wing nut in the centre allows you to join the plate to the corner and do it up tightly.

12. 3.3 Joining methods (temporary): Knock down fittings
Chipboard fastener
As the screw thread would not be able to grip inside the chipboard, a rawl plug is placed inside the hole. This allows the screw to grip onto something and as the screw is screwed into the plug, it expands and allows the screw to make a strong joint.
Rawl plug
Screw

13. 3.3 Joining methods (temporary): Knock down fittings
Block connector
Screws holding the first block in place.
This is the screw that can be done up and undone when needed.
This fitting allows a piece of furniture to be taken apart without the need to remove all screws. This is particularly important in chipboard constructions as repeated screwing into chipboard will quickly result in stripped threads and reduced holding power.

14. 3.3 Joining methods (temporary): Knock down fittings
Advantages of uses
knock-down fittings
For manufactures
For consumers

15. 3.3 Joining methods (temporary): Knock down fittings
Disadvantages of uses
knock-down fittings
For manufactures
For consumers