1. An Introduction to Water Rocketry
Mr. Young
Roberts Elementary School
Science Specials

2. Parts of a Basic Water Rocket

3. Parts of Rocket (cont.) Nose Cone- For aerodynamic effect
Ballast (not always necessary) but adds mass to rocket for increased stability.
Fins- for stability
Pressure vessel- source of rocket propulsion. Must be airtight!

4. When preparing your 2-liter bottle do not use the following items:
Hot/Boiling water Knives/Razors
Sandpaper Chemicals
*These things may compromise the structural integrity of the bottle.
Remember it is pressurized with air!

5. What Do I Need?
One 2-Liter bottle (or more bottles if you want to make a tall rocket)
Materials for Fins
Materials for Nose Cone
Tape/Glue
Scissors
Marker

6. The Rocket Body One bottle is all that is needed for a basic rocket.
If you want to make a taller rocket cut the bottom portion off another two liter bottle.

7. Rocket Body: Ballast
If you want to add some ballast to your rocket you can use items such as: sand, foam peanuts, modeling clay, newspaper, etc.

8. Rocket Body (cont.)
Push bottom half of two liter bottle upside down into top half – to keep ballast in place.
Use small pieces of tape to secure bottom piece inside bottle.

9. Rocket Body (cont.)
Place two liter bottle (pressure vessel) into top half. Try to make bottles straight. Use little pieces of tape to secure bottles. This is not necessary if you are using a single bottle.

10. How Do I Attach Fins & Nose Cone?
I have found these items work best. Also, PL Premium Glue from Home Depot is excellent. The packing tape with strings is my favorite. It holds really well and makes it easier to repair your rocket quickly!

11. Fins are the guidance system for your rocket.
Square/Trapezoidal:
Fins yield MORE stability, but create MORE drag.
Triangular/ Epsilon:
Fins introduce LESS drag, but yield LESS stability.

12. Materials for Fins Milk or Juice bottle Foam trays
Unused election signs (work great & are water proof)
Cardboard
Corrugated Plastic
Plastic Folders
Poster board

13. Fin Templates (or design your own!)

14. Fins
Use a template, a marker and draw fin patterns on the material you have chosen to use.

15. Fins (cont.)
Cut fins out.

16. Measure for Fins
Measure your rocket to make sure the fins are equally placed around bottle.

17. Fins (cont.) Attach fins to rocket using tape or glue.
Use either 3 or 4 fins.
More than four adds unnecessary weight.

18. Materials for Nose Cone
You can use many materials to make a nose cone.
To create a rounded tip you can use an egg carton or a plastic egg shell.
Small Nerf footballs, foam noodles, foam balls, etc. all work well & allow the rocket to make a soft landing!

19. Nose Cone Materials

20. Nose Cone
Roll your material (plastic file folders work great) into a cone.
Use tape to hold material in place.
Place plastic egg shell on the cone as tip. Use tape to fasten tip to cone.

21. Nose Cone (cont.)
Fasten nose cone to the body with tape or glue.

22. Decorating Your Rocket
You may decorate with stickers, paint, wrapping paper, etc.
The bottom of your rocket though must remain clear of any obstructions.
Fins cannot extend past bottom half so that the rocket will fit on the launcher.

23. How Do I Launch My Rocket?

24. Launch Pad

25. Mr. Young’s attempt at creative rocket building!

26. BE AS CREATIVE AS YOU WANT !!
Tips
Lengthening the rocket adds stability
Experiment with different fin shapes
Try different body shapes
Try to make the body smooth (no kinks with tape).
Do not use a hot glue gun, super glue, masking tape, scotch tape, wood or metal on your rocket.
BE AS CREATIVE AS YOU WANT !!
HAVE FUN!!