1. Multi-tasking OKUMA Multus B300W

2. Multi-tasking Mori-Seiki NT

3. Multi-tasking Mazak Integrex Mark IV

4. Multi-tasking Machine Definition

5. Multi-tasking Axis combinations

6. Multi-tasking Axis combinations

7. Multi-tasking Stock Setup

8. Multi-tasking Tool Setup – Define lathe tools in B=0 position.

9. Multi-tasking Tool Setup – Define lathe tools in B=0 position. Mazak Integrex Okuma Multus Mori Seiki NT

10. Multi-tasking Tool Angle – One tool can be defined to work in any possible configuration using Tool Angle Tool Angle = BA: Angle (Okuma Multus) Tool Orientation on Machine: Indexes a tool to work on Left spindle or Right spindle and for back turning on either spindle (M602 or M603- Okuma Multus)

11. Multi-tasking Tool Orientation on Machine: Indexes a tool to define Position B (Okuma Multus - M602 or M603) N220G97 G95 S=3800 M42 M602 BA=90. TL=011011

12. Multi-tasking Tool Orientation on Machine: Indexes a tool to define Position B (Mori-Seiki NT D1 or D2)

13. Defining Lathe tool output Tool ID Code: MR2 For consistency, the general guidelines below are suggested

14. Multi-tasking Tool Orientation on Machine: Indexes a tool to define Position B (Integrex Mark IV - Matrix) (PROGRAM NAME - MULTI-TASKING DEMO_MJR1 DATE=DD-MM-YY - 22-02-09 TIME=HH:MM - 13:47 ) (POST LICENSE - IN-HOUSE SOLUTIONS INC.) (T11 | CNMG 08 OD R | DIA. - 11 | SUFFIX -.02 | INSERT - CNMG 12 04 08) G21 G69 G80 G40 G18 G90 G94 M205 (UPPER TURRET) G109 L1 (T11 | CNMG 08 OD R | DIA. - 11 | SUFFIX -.02 | INSERT - CNMG 12 04 08) (TOOLPATH GROUP - PREP STOCK ) G21 G10.9 X1 N1 G91 G28 X0. N1 G28 Y0. Z0. M901 M202 T11.02 T11 M06 G91 G28 X0. Z0. G90 M108 G0 G90 G53 B90. M107 G54...

15. Multi-tasking N220G97 G95 S=3800 M42 M602 BA=90. TL=111111 N230 M4

16. Multi-tasking Program: Facing / Drilling / ID Boring

17. Multi-tasking Misc Ops: Stock Flip

18. Multi-tasking Misc Ops: Stock Flip

19. Multi-tasking Face / Drill / ID Bore (rough) / ID Bore undercut finish

20. Multi-tasking ID Bore undercut N220G97 G95 S=2816 M42 M602 BA=-10. TL=330933 N230 M4

21. Multi-tasking OD Rough / Finish / Plunge Cut Parameters

22. Multi-tasking OD Finish Back turning N220G97 G95 S=509 M41 M603 BA=90. TL=004004 N230 M3

23. Multi-tasking Finish ID / Thread OD

24. Multi-tasking Mill slot / Transform toolpath T/Cplane TOP in Mill is C=90. BACK is C=0... N210G94 SB=2000 M241 M63 M9 BA=90. G52 TL=303030 N220 M13 N230 G138 N240 G17 N250 M146 N260 G0 C90. N270 M147 N280 G127 B90. N290 G0 Z155. N300 X37.5 Y0. N310 Z65....

25. Multi-tasking Circle Mill counterbore / Drill / Tap angled holes

26. Multi-tasking Misc Ops: Stock Flip back to OP1 position Geometry exists already. Transfer geometry not required

27. Multi-tasking Stock Flip – Original position

28. Multi-tasking Face – Stock recognition

29. Multi-tasking Rough / Semi-finish ID

30. Multi-tasking Rough OD / Finish OD

31. Multi-tasking Thread

32. Multi-tasking Finish corners