1. Our mission is to combat the spread of infectious diseases through a family of comprehensive, cost-effective, and environmentally safe solutions. AeroClave, LLC Facility, Vehicle, and Equipment Decontamination Solutions

2. 2003-2006 Decontamination of large aircraft ACER/ECBC validation work (Air Cabin Environmental Research/Edgewood Chemical Biological Center) Harvard viral studies 2006-2007 CAMI 747 and rail car work (Civil Aeronautical Medical Institute) 2007-2011 AFRL/AMC TESTS (Air Force Research Lab/Air Mobility Command) Complete kill of anthrax simulant through entire aircraft with no damage to aircraft Multiple tests – 0 failures Beat time-to-kill estimates by over 50% History of AeroClave

3. History of AeroClave (cont.) 2008-2009 Development of a Portable Asset Decontamination System (PADS) in Winter Park, FL 30’, 60’ or 100’ chamber configuration EMS, fire and law enforcement use this chamber to sterilize their vehicles 2009-2014 Development of Room Decontamination System (RDS) Sterilizes rooms up to 8,000 cubic ft. Simply move from room to room Development of the Hydra System for building integration Development of Ambulance Decontamination System (ADS)

4. AeroClave Process AeroClave solution is evenly applied onto surfaces in two different ways. Hand-applied* – for spot-treating and quick decontamination of high- contact areas Fogging – for total decontamination of desired treatment area Hand-applied method*Fogging method *Use of PPE may be necessary depending on solution being used

5. Pulsed Application Process (Fogging) 1.Injection Phase: In this phase, the decontamination solution is aerosolized and applied evenly to the treatment area. A typical injection phase will last anywhere from 10-30 minutes, depending on the size of the treatment area. 2.Dwell Phase: Once the injection phase has completed, the treatment area is allowed to sit in a dwell period for a minimum of five minutes. The dwell period gives the aerosolized solution an opportunity to evenly distribute throughout the treatment area, ensuring full coverage on all surfaces. 3.Aeration Phase: The aeration phase is when the solution is removed from the treatment area. This can be done in various ways; reenergizing the facility HVAC, providing external ventilation, promoting air circulation, etc. The solution will also naturally break itself over a period of time, if none of these aeration options are available,

6. Room Conditioning Injection Dwell Aeration Injection time is typically 5-30 minutes (depending on size of space) Much faster than most other technologies Dwell cycle time is typically 5-10 minutes Many other technologies must reach micro-condensation before going into dwell Aeration is dependent on HVAC system or exterior ventilation Average Total Cycle Time (start to finish) is about 45 minutes Typical AeroClave Cycle

7. System Information RDS 6110 ADS RDS 3110

8. Room Decontamination System RDS 3110 Rugged and Lightweight – 45 lbs. Can effectively treat spaces up to 600 ft 2 Fast: Average turnaround of a patient room is around 45 minutes Average turnaround of an ambulance inside and out is less than 30 minutes Average turnaround of an ambulance patient compartment is less than 15 minutes Versatile – can be operated in either a fogging or hand-applied method. Simple to use – minimal operator training required Two unit variations: 2 Fixed Heads and 1 Port (Shown) 3 Ports RDS 3110 shown with AeroClave Portable Applicator (APA)

9. 3 Port Variation: Can be used as either a remote head fogger or manually hand- sprayed* *Use of PPE may be necessary depending on solution being used

10. Room Decontamination System RDS 6110 Portable Can effectively treat spaces up to 1,500 ft 2 Fast: Average turnaround of a patient room is around 30 minutes Average turnaround of an operating room is less than 60 minutes 4 fixed spray heads and 2 ports Fully customizable facility programming Facility and asset management tracking software Simple to use – minimal training required Versatile – can be operated in either a fogging or hand-applied method. RDS 6110 shown with AeroClave Portable Applicators (APA)

11. Room Decontamination System RDS 6110

12. RDS 3110 and 6110 Applications Surgical suites, in and out-patient Physician offices and health clinics Patient, diagnostic, and procedural rooms Research facilities Locker rooms and gymnasiums Local, state, and federal assistance offices Educational facilities from pre-school to college Veterinary hospitals and animal shelters Law enforcement offices, jails, and holding cells Food service and preparation areas Cruise ships Hotels

13. Ambulance Decontamination System (ADS) Fully integrated patient-compartment system Fully automated operation Can be operated in-station or on the road Fast – average cycle time 15 minutes Management tracking software

14. Ambulance Decontamination Port (ADP) Can be installed in either rooms or vehicles Eliminates excess manual labor and exposure in contaminated areas Ensures consistent operation and results Allows for one system to decontaminate up to 3 or 6 different rooms or vehicles simultaneously Can be flush mounted (left) or mounted with optional pig tail (above) for access Compatible with all AeroClave systems Cost effective Easy to install

15. Ambulance Decontamination Port (ADP) Ports connect to spray heads that are permanently mounted in the treatment area

16. AeroClave Portable Applicator (APA) Accessory for use with all AeroClave systems 25’ cable with SmartPort connector Allows for both manual hand-application or remote-head fogging Smart switch located in mounting point notifies AeroClave system of intended APA use Hand-application is ideal for: Exterior settings Individual pieces of equipment Quick spot-treatment on high contact surfaces Remote-head fogging is ideal for: Expanding the treatment footprint of AeroClave systems Fogging in small areas Fogging in irregularly-shaped areas

17. The AeroClave Advantage Most cost-effective product line Quickest average cycle times Simple automated operation Comprehensive suite of facility and asset management tools Environmentally-friendly process (“green”) Cost-effective operation per treatment cycle No residues - nothing to wipe down or wipe off Compatible with sensitive electronics Broadest range of materials compatibility Broadest range of product solutions for every industry